Can not tune any sats other than 13E and 19.2E

[dazv]

Hi Am new to this forum and the DM800HD. Am using the NabiloSat Blackhole image (latest). When trying to tune I can only see 2 satellites 13e and 19.2e. Q1 is How do I add other sat's? and am going to setup a motor so Q2 how do I tune in using a motor. Cheers in advance.:stupid:

[westkill]

what dish setup you got ,is it a motorised dish ?

[jdunlo]

follow this mate iv taken it from a tutorial with pictures but iv omitted the pictures. i am not the author of the tutorial

guide to setting up your DM800 tuner
Image Used - Blackhole V0.12
If your using DiSEqC 1.2 you will have to set-up the dish positions manually. If your usuing USALS
it should be automatic.
Here's the USALS procedure that I used on mine
First make sure the dish is correctly aligned on a satellite, eg Astra 28.2e
Press Menu
Set Up
Service Searching
Tuner Configuration
Choose Tuner ALPS BSBE2 (DVB-S2) - Press OK
Now for my configuration??..
Configuration Mode: Advanced
Satellite : Astra 2A/2B/2D/Eurobird 1 (28.2e)
Change LNB to LNB 1
Priority : Auto
LOF: Universal LNB
Voltage Mode: Polarization
Increased voltage: yes
Tone Mode: band
DiSEqC Mode: 1.2
Toneburst: None
Committed DiSEqC: None
Fast DiSEqC : no
Sequence repeat : no
Command order : committed toneburst
Uncomitted DiSEqC command : None
DiSEqC repeats : none
Longitude: Set this to the correct Longitude for your area.
To find the correct longitude settings for your area go to the following website
Worldwide map search, route finder and travel directions - powered by Multimap (http://www.multimap.com/)
In the "Find a Map" box at the top left of the page, enter your post code.
Select your country in the drop down box below it and click on the "Find" button.
This will display a map on the screen and below the map at the bottom right you
will see your Latitude information, example below for Postcode district:NE39 1
Lat:54:55:09N (54.91913)
Lon:1:44:55W (-1.74859)
So in this example in the Dreambox menu you'd set
Longitude: 001.748
West
Latitude : 54:550
North
Use USALS for this Sat: Yes
PRESS OK TO SAVE
Once this is set up on one satellite its easy to sort the rest.
Go back into reception settings
Highlight satellite and choose the satellite you want
The example here shows Hellas on 39.0e
Now select LNB and change to LNB 1
This will fill in the configuration with your previously set configuration
PRESS OK TO SAVE
Repeat for the other sats you are looking to pick up

[network-nt]

I think you'll find it was pre-setup. If you run a factory reset, you'll be able to select any satellite you want. Hope this helps!

[kamel22]

follow this mate iv taken it from a tutorial with pictures but iv omitted the pictures. i am not the author of the tutorial

guide to setting up your DM800 tuner
Image Used - Blackhole V0.12
If your using DiSEqC 1.2 you will have to set-up the dish positions manually. If your usuing USALS
it should be automatic.
Here's the USALS procedure that I used on mine
First make sure the dish is correctly aligned on a satellite, eg Astra 28.2e
Press Menu
Set Up
Service Searching
Tuner Configuration
Choose Tuner ALPS BSBE2 (DVB-S2) - Press OK
Now for my configuration??..
Configuration Mode: Advanced
Satellite : Astra 2A/2B/2D/Eurobird 1 (28.2e)
Change LNB to LNB 1
Priority : Auto
LOF: Universal LNB
Voltage Mode: Polarization
Increased voltage: yes
Tone Mode: band
DiSEqC Mode: 1.2
Toneburst: None
Committed DiSEqC: None
Fast DiSEqC : no
Sequence repeat : no
Command order : committed toneburst
Uncomitted DiSEqC command : None
DiSEqC repeats : none
Longitude: Set this to the correct Longitude for your area.
To find the correct longitude settings for your area go to the following website
Worldwide map search, route finder and travel directions - powered by Multimap (http://www.multimap.com/)
In the "Find a Map" box at the top left of the page, enter your post code.
Select your country in the drop down box below it and click on the "Find" button.
This will display a map on the screen and below the map at the bottom right you
will see your Latitude information, example below for Postcode district:NE39 1
Lat:54:55:09N (54.91913)
Lon:1:44:55W (-1.74859)
So in this example in the Dreambox menu you'd set
Longitude: 001.748
West
Latitude : 54:550
North
Use USALS for this Sat: Yes
PRESS OK TO SAVE
Once this is set up on one satellite its easy to sort the rest.
Go back into reception settings
Highlight satellite and choose the satellite you want
The example here shows Hellas on 39.0e
Now select LNB and change to LNB 1
This will fill in the configuration with your previously set configuration
PRESS OK TO SAVE
Repeat for the other sats you are looking to pick up

Im new to Usals settings. what happens after pressing ok to save.will the dish scans automatically or i need to do something. thanks in advance.