Kia, Suzuki & LandRover Discovery im*os

[cristi_onofrei]

I still need help for this cars:

Kia Sportage 2L petrol 1999
ECU Bosch 0261204941
im*o Texton 93c46

Suzuki Jimny 1998
ECU DENSO with eeprom 93c56
im*o Mitsubishi with eeprom 24c01

LandRover Discovery 1995
ECU 0 281 001 352
eprom 2 x 27c256
eeprom 2 x 93c46

I need im*o off solutions or good peers

[cristi_onofrei]

no news for this cars?

[teerak2uk]

What is the problem with the discovery why do you need immo off

[cristi_onofrei]

remote work, but I can't sync ECM with alarm module

I can't input EKA code

[cristi_onofrei]

Suzuki Jimny solved

[teerak2uk]

have you checked spider module they are prone to dry solder joints

[cristi_onofrei]

Thank you, but what is spider module?
receiver for remote look good

[teerak2uk]

Take out the heater controls...

http://img.photobucket.com/albums/v120/sclfk/Spider/Dash4.jpg

...take out the clock & hazard light switches, and the switch blanks from underneath...

http://img.photobucket.com/albums/v120/sclfk/Spider/Dash6.jpg

...take out the coin tray and ashtray (note one of the screws in behind the coin tray, this holds the whole centre console panel in)...

http://img.photobucket.com/albums/v120/sclfk/Spider/Dash7.jpg

...out with the radio etc, and then the drinks holder from underneath...

http://img.photobucket.com/albums/v120/sclfk/Spider/Dash8.jpg

...then once you have found all the screws, pull out the whole main plastic centre console panel so it looks like this...

http://img.photobucket.com/albums/v120/sclfk/Spider/Dash12.jpg

Now you can see the spider (arrowed)

http://img.photobucket.com/albums/v120/sclfk/Spider/Dash13.jpg

[teerak2uk]

Unscrew the two screws holding it in, pull it out, then unplug it...

http://img.photobucket.com/albums/v120/sclfk/Spider/Dash14.jpg

...and here it is, the little *&*&%$^ Resist the temptation to stamp on it, as you can't buy them any more!

http://img.photobucket.com/albums/v120/sclfk/Spider/Dash19.jpg

Carefully lever out the end plate with a flat bladed screwdriver and the circuit board will slide out...

http://img.photobucket.com/albums/v120/sclfk/Spider/Dash20.jpg

See the problem?

http://img.photobucket.com/albums/v120/sclfk/Spider/Dash21.jpg

If not, look a little closer at the arrowed joints, particularly the top left one....

http://img.photobucket.com/albums/v120/sclfk/Spider/Dash21a.jpg

[teerak2uk]

A less than perfect bit of soldering http://forums.lr4x4.com/public/style_emoticons/default/mad.gif While you are in there, re-solder all the pins going onto the multiplug in the end, and all the pins going onto the 2 relays on the board, as any of them can go and I don't suppose you want to take it out again! The re-soldered article ready to go back together:

http://img.photobucket.com/albums/v120/sclfk/Spider/Dash22.jpg

It can be much worse and more obvious than this, in extreme cases the tracks can be burnt away and you have to re-build the tracks joining the pins, which I do with fine solid-core wire, but even one that is only just starting to go is not hard to spot when you know where to look

[cristi_onofrei]

WOOWW!!!
Thank you very much for detailed description
I will check tomorrow
Thank you again!

[teerak2uk]

Your welcome i hope it helps you

[nutloose]

FYI
as they are no longer available the dealers will now supply a spider bypass loom instead to do away with it.

Oh and some diagnostic tools(T4) refer to the spider module even when they weren't fitted!

[johannstamos]

Suzuki Jimny solved
can help me for the jimny?

[cristi_onofrei]

give me original dumps

[cristi_onofrei]

Hi teerak2uk (http://www.digital-kaos.co.uk/forums/members/48778-teerak2uk/)!
I get out heater control, clock and all around nut I can't find spider
maybe in other place?

[teerak2uk]

may need to look around as maybe someone has already repaired it and placed it somewhere easier to reach for next time try to look around steering column area

[cristi_onofrei]

in my car I have only a big box from air blower and don't exist space for spider module. this car is right hand. can be any difference or maybe don't have this module ?

[twardy12345]

hello all:)

cristi_onofrei - can you may help me with jimny?? what tool do you use if its not very topsecret :)

[cristi_onofrei]

tech2 with suzuki card

[kugglefischer]

give me original dumps
hi
ive got one question about this suzuki jimny ...do you do an immo off? or just make it virgin, so you can code new keys to immo box?

a few lines would be helpful...thanks!

K:giveup:

[cristi_onofrei]

no immo off

resync ECU with immo and after that program keys

That's all !