cas3 programer

[simon77]

i have got a cas3 programmer cas/9s12x bdm with rosfar software(chineese clone)
i asked for a red one and got a blue one .
i can read ezs for mercedes 209 and 211 and cas 1,2 providing it has MC9S12
if i try to read hc12 it wont connect to board just trie linking 6 times and out.
i need to read a dash for a 2003 mini and i cannot.
is there any one out there that can help out in fixing the cas programmer or do i have to buya new one. cant send this one back as i have had it for a while using it for cas only.
or is there away to power up the board so that i can read it
regards

[hcip]

update the FDTI driver for the newest one

[atesbocusu]

i have got a cas3 programmer cas/9s12x bdm with rosfar software(chineese clone)
i asked for a red one and got a blue one .
i can read ezs for mercedes 209 and 211 and cas 1,2 providing it has MC9S12
if i try to read hc12 it wont connect to board just trie linking 6 times and out.
i need to read a dash for a 2003 mini and i cannot.
is there any one out there that can help out in fixing the cas programmer or do i have to buya new one. cant send this one back as i have had it for a while using it for cas only.
or is there away to power up the board so that i can read it
regards



i have this cas3 programmer and i wanna make cas3 but when time reading program say decoding and my pc frozen.. and know this problem ?

[deffc0n]

Check diffrent PC :)

[leon.79]

Hi
i have the same problem but i have a red chinese clone
cant read normal cas 2 and 3 only cas3 x .
where can i find the newdriver?

thanks

[motorsport]

Hi
i have the same problem but i have a red chinese clone
cant read normal cas 2 and 3 only cas3 x .
where can i find the newdriver?

thanks

hi have red case where have you buy your i have same probleme i have make great cas3XDP512 but cas3 9S12DG256 sofware go at licking 1 2 3..6 and say me securised and dont read !!!!

[simon77]

powered up clocks with external power done the job
thanks all for your help
regards

[leon.79]

Hi

thanks but can you explain a little more
what is power up clocks with external power.


thanks

[DON SRK]

I would like to know too


Thanks mate

[leon.79]

found out about the external power but still no linking
anyone got more ideas?

thanks

[leon.79]

found the problem
for cas2 reading

swith the black and whit cable of the coax on the crystal
reads and write without a problem

hopes works also for you let me know

[whiskymk]

Maybe someone have dump from atmega for cas3 programmer?

[motorsport]

found the problem
for cas2 reading

swith the black and whit cable of the coax on the crystal
reads and write without a problem

hopes works also for you let me know

hi my friend can you give me more detail i dont understand swit black whith coax cable if you can post picture your modification thanks so mutch :stupid:

[leon.79]

there are 2 wires on your cable
1 is with 5 colors
2 is with one black and one white(coax cable)

inthe manual it says where to solder the cables
now solder the 5 colors on the places as in the manual
then you have 2 wires left , one black , one white (coax)
solder the white cable on the place of the black and the black on the place of the white.

Let me know or it also works for you

[motorsport]

there are 2 wires on your cable
1 is with 5 colors
2 is with one black and one white(coax cable)

inthe manual it says where to solder the cables
now solder the 5 colors on the places as in the manual
then you have 2 wires left , one black , one white (coax)
solder the white cable on the place of the black and the black on the place of the white.

Let me know or it also works for you

strangely it need reverse black and white coax wire right?
because on the cas3XDP512 i have make correctly coax cable same in picture manual and work fine software go on decoding but cas3 BLACK 9S12DS256 with same picture manuel go on likcking

[leon.79]

yes exactly try it

[didi_du_93000]

Hello,

I have the same problem as you.
I have Blue cas3 programmer.
When i try to read a CAS3 (black) of my BMW 330D 2007 year. The software say me: securised
and it don't read the MCU.
Have you found a solution?
The problem is it the supply?
Can you explain me please?
Thanks a lot?