PDA

View Full Version : E39 520D Bosch 0281010205 bad flash



sl4ck
19th April, 2010, 07:34 PM
M8's need help please, i went to a bad flash with BMW E39 520D 136HP.

First i was able to recover original file with galletto, and i flashed with another one not compatible, i didn?t know, now i'm trying to flash with original one but it gives INIT ERROR.

With a more extensive search i was able to find out that it uses two files?! HI and LO ?!

Has far has i know ECU files from 136HP e46(320d) and e39(520d) are the same, i have them both(HI and LO), but how can i flash it?

Should i use my original i read from my ECU, but it's not HI neither LO or use this ones, and how can i flash them both?!

Regards

bmw320d
19th April, 2010, 07:48 PM
You can write it directly with a programmer plcc32, or modify the two dump into one, in this case you can upload in the ecu with galletto

sl4ck
19th April, 2010, 09:16 PM
When we use galletto to read original dump from this ECU it reads the two files buy into one?

What's the difference between HI and LO ?

How can i modify the two files into one ?

How can i upload it with galletto if it has INIT -1 ERROR ??

Sorry but i?m really mad, because it's my daily car.

Thanks

VOLUMAX
19th April, 2010, 09:32 PM
Now I think that there have only one method for recovery . Desolder the two plcc32 chips and write them on the programmer !

sl4ck
19th April, 2010, 09:35 PM
Are there two chips?

How do i know wich one is HI and LO ?

Can i split my galletto file into one, or galletto only reads one chip?

VOLUMAX
19th April, 2010, 09:44 PM
Yes there are two chips inside the ECU !
Galleto join the two files in one while reading them !

2 X 128 kB = 1 X 256 kB

sl4ck
19th April, 2010, 09:59 PM
can you help me identifying the chips ?

HI and LO


:wink:

VOLUMAX
19th April, 2010, 10:07 PM
Here is it

sl4ck
19th April, 2010, 10:18 PM
What's chip's identification to use in programmer?

Both have stickers with numbers on top like:

351343010205110161

and

351344010205110161

and i don?t whant to remove them.

Thanks again

VOLUMAX
19th April, 2010, 10:29 PM
There are Flash PLCC 32 29F010

The first 6 digits are a SW ! X XXX 351 343 is Lo bite chip and X XXX 351 344 is Hi bite !

The second 6 digits are HW of ECU X XXX 010 205

Maybe you don't want but have :)

sl4ck
20th April, 2010, 12:39 AM
After i flash both HI and LO chip's with PLCC32 adapter and a programmer with files posted on first post (downloaded from another forum) car didn?t start again, but galletto INIT error stopped and i was able to flash it again with galletto my original flash i had saved with galletto.

Can someone explain why car didn?t start with files posted on first post?

Thanks

bmw320d
20th April, 2010, 09:19 AM
After i flash both HI and LO chip's with PLCC32 adapter and a programmer with files posted on first post (downloaded from another forum) car didn?t start again, but galletto INIT error stopped and i was able to flash it again with galletto my original flash i had saved with galletto.

Can someone explain why car didn?t start with files posted on first post?

Thanks

You use socket plcc32? or the eprom are directly on pcb? after having upload the file in the eprom with the programmer you has verified if the dump are the same? the file upload in eprom has the correct checksum?

sl4ck
20th April, 2010, 10:25 AM
I have desoldered the two chips and programmed with the PLCC32 to DIP adapter.

Dunno if the checksum was the same, but after i flashed the two desoldered chips with the programmer i was able to program ECU with galletto and with my galletto saved file (256kb) i had done before

Maybe it doesn?t start with the two first files because immo? Where is Immo in this ECU?

Is there any way to split my original galletto saved file in two (HI and LO) ?

bmw320d
20th April, 2010, 11:13 AM
I have desoldered the two chips and programmed with the PLCC32 to DIP adapter.

Dunno if the checksum was the same, but after i flashed the two desoldered chips with the programmer i was able to program ECU with galletto and with my galletto saved file (256kb) i had done before

Maybe it doesn?t start with the two first files because im*o? Where is im*o in this ECU?

Is there any way to split my original galletto saved file in two (HI and LO) ?

the immo is in the two eprom and in the e2prom 24c02, upload here your full dump 256kb from galletto, so I can split it in Hi e Lo

sl4ck
20th April, 2010, 11:36 AM
I'll do when i be at home.

So, the car could not start because of the immo in the files in first post aren?t from my car and immo info is not the same, could be because of this?

VOLUMAX
20th April, 2010, 11:54 AM
Now you can to write original file who you read from your ECU with Galleto !
After that if the car don't want to start you must to do
EWS - DDE synchronization

bmw320d
20th April, 2010, 12:08 PM
I'll do when i be at home.

So, the car could not start because of the im*o in the files in first post aren?t from my car and im*o info is not the same, could be because of this?

yes, you cann't upload a full dump of another bmw because the car not run for error in ews, but you must tuning your map? I can to do it

sl4ck
20th April, 2010, 01:17 PM
Now you can to write original file who you read from your ECU with Galleto !
After that if the car don't want to start you must to do
EWS - DDE synchronization

Yes, that's what i did, and it start fine.



yes, you cann't upload a full dump of another bmw because the car not run for error in ews, but you must tuning your map? I can to do it

Yes, i want to tune my map, if you can do it will be gratefull, when i arrive home i post my dump.

Is there any way can start my car with with another car full dump?

Thanks again you all, have been very helpfull

sl4ck
20th April, 2010, 01:37 PM
Here is my original file:

:wink:

bmw320d
20th April, 2010, 01:45 PM
try to reprogram the eprom L and H and test if car run

sl4ck
20th April, 2010, 02:38 PM
Car already runs with the 256kb file i posted.

Is it the tunned file?

Could you please post it in one 256kb file instead 2x 128kb, so i don?t have to desolder chips again and can reprogram it with galletto?

Thanks

bmw320d
20th April, 2010, 07:09 PM
Car already runs with the 256kb file i posted.

Is it the tunned file?

Could you please post it in one 256kb file instead 2x 128kb, so i don?t have to desolder chips again and can reprogram it with galletto?

Thanks

.....a moment please! but if the car run with your file of 256kb, why you have need of split this file in Hi e Lo?
the dump not is tuned is original

sl4ck
20th April, 2010, 07:49 PM
Sorry by miss understand, maybe my english made this, but has i said in previous posts, after i desoldered chips flashed with files in first post(i download from another forum) and soldered chips again in ECU, the car didn?t start, BUT after that, INIT -1 ERROR stopped in galletto, and i was able to program ECU again with Galletto and my original backup file, and then the car starts!!

Then, i asked if there's a way to JOIN the 2x 128kb files (HI and LO) in the 256kb file or SPLIT the 256kb file in 2x 128kb (HI and LO) for knowloedge, and to know how to do it even with my car running.

I thought you have understanded before, and i post my original backup file (256kb) because you said you can tune it, it was not for you to split it.

Thanks again, and sorry for my bad english

bmw320d
20th April, 2010, 10:36 PM
Sorry by miss understand, maybe my english made this, but has i said in previous posts, after i desoldered chips flashed with files in first post(i download from another forum) and soldered chips again in ECU, the car didn?t start, BUT after that, INIT -1 ERROR stopped in galletto, and i was able to program ECU again with Galletto and my original backup file, and then the car starts!!

Then, i asked if there's a way to JOIN the 2x 128kb files (HI and LO) in the 256kb file or SPLIT the 256kb file in 2x 128kb (HI and LO) for knowloedge, and to know how to do it even with my car running.

I thought you have understanded before, and i post my original backup file (256kb) because you said you can tune it, it was not for you to split it.

Thanks again, and sorry for my bad english

ok, now I can modify your original dump, you must have a little of patience

bmw320d
21st April, 2010, 01:40 PM
Hi, in attach map mod of your map
try and report it

richisup
21st April, 2010, 02:25 PM
Hi all, Im looking for a tuned map for my BMW E91 320d 2006 model. I believe it has the edc16 ecu - any help on this would me much apreciated.

thanks :)

sl4ck
21st April, 2010, 03:29 PM
Thanks m8!

bmw320d
21st April, 2010, 10:42 PM
Thanks m8!

Try it :top: