honda civic 1.4 esi Imm*

[el_futte]

have a problem whit a honda from year 96 the customer have lost he key and only got one but no transponder hey in it

so its blinking in the cluster for key ..

the ecu is a 37820-p3y-g01

when i read the 93c46 there is no data on it do any body knogs 2 handle this one ??

[VOLUMAX]

What you want to do ? Immo off or repair ?

[el_futte]

sorry ;O)

im*o off

[VOLUMAX]

Inside the ecu has a little board with OKI M851G . Remove it and the engine will started !

[el_futte]

oaky done its only the serial eprom i need 2 remove ??

[VOLUMAX]

Remove little board with OKI ! No only OKI !

[VOLUMAX]

Here is it

[Meat-Head]

Seem to think, the word on the street is the MIL will be on.

[VOLUMAX]

Seem to think, the word on the street is the MIL will be on.


Yes it is true ! The MIL will be ON !
But i don't know other way :stupid:

[Meat-Head]

Yes it is true ! The MIL will be ON !
But i don't know other way :stupid:

Honda - IMMO (http://www.codecard.lt/immo/honda/cat_30.html) but this is was 96 think it was at top of page

[VOLUMAX]

Honda - im*o (http://www.codecard.lt/im*o/honda/cat_30.html) but this is was 96 think it was at top of page


I know about that, but I wanted to suggest something for free :)

[el_futte]

i have know desolder the hole one you have marked whit red.. and when i try 2 start the car the starter do not do anything ??

[mariusssmache]

I can help you with immo code if you give me the vin of the car.

[VOLUMAX]

i have know desolder the hole one you have marked whit red.. and when i try 2 start the car the starter do not do anything ??

Yes the immo box blocked starter motor relay .
You must to solve this problem too !

[ADEL.KSHLAF]

hi all :listen:

Honda cars year 1995-1998 (Civic, Accord and others). Inside immo board looks
like in picture. On this board is small 44pins processor and OKI M851G EEPROM
(you can read/write it like 93C46). Most common problem with this type
immobilizer is IMMO-ECU synchronization lost (this happens when ignition are
switched ON with red key). To solve this problem just erase OKI M851G
EEPROM to FF...FF.

To disable immobilizer just remove immobilizer board (marked in red on photo)
from motor ECU. Honda immo emulator is no needed for this kind of ECU. :captain:

[Meat-Head]

the last post in this is nearly a year out of date


funny though was in a eleator rin block of flats last nite in there was ambulance crew on way to a breakdown bloke was saying about a company called autolec on the isle of white can emulate the later honds

but then he ran off

[ssemmedo]

how to solve this problem i have exactly the same problem. i remove the board and the car didn?t crank. now i remove the 9346 inside the immo box. i have the black key with data and i need to write the key data to the 93C46 chip. If some one can tell me how to write it.

[Meat-Head]

feeling of dejau vous just had a thread like that

yeah must get roud to writing up what i did with the other one i had.

[ssemmedo]

i couln?t understand you. any way thanks a lot. But i still need help to write the key data to the immo dump.

[Meat-Head]

But i still need help to write the key data to the immo dump.

YES PLEASE that would be aswesome if you can figure it out thanks.

[ssemmedo]

I?m trying to solve this situation. i take out the small board inside the ecu the car did not start; i read the 93C46 eeprom inside the immo box and i post it here in DK; i read the M851G eeprom on the immo pcb and i posted it here in DK; e have the zedbull clone with one i read the Black key data. Now i wanted to know if there are some one to help me writing the key data inside the immo box eeprom 93C46. I?d apretiate and i can pay by paypal if the help solves my problem.
Best regards.

[ssemmedo]

The immo box in this case don?t let the starter work. in this case try to locate the relay under the steering wheel and shorter it. the car will crank and start if you are locky.

[Meat-Head]

Ok so how did you fix the immo,(?

[TR0UBLESH00TER]

Or put a jumper wire in immo box connector from pin 3 to 8 so starter will work .Also jumper from pin 5 to 6 on 10 pin connector so you can do diagnostic .