Outlander MN141 500 DPB mem dump

[juzek]

I'm looking for valid memory dump for Mitsubishi Outlander (2006 Year/US Spec) MN141 500 DPB W2T62771. Memory s93c56. I Someone could help me with dump for this one it will be great (without crash data will be super, but also with crash data stored will be fine). I can't communicate with srs ecu in this car - i suspect that eeprom was damaged/wrong programed before car was driven to me. Thank You.
Regards

[juozas10]

I'm looking for valid memory dump for Mitsubishi Outlander (2006 Year/US Spec) MN141 500 DPB W2T62771. Memory s93c56. I Someone could help me with dump for this one it will be great (without crash data will be super, but also with crash data stored will be fine). I can't communicate with srs ecu in this car - i suspect that eeprom was damaged/wrong programed before car was driven to me. Thank You.
Regards


Hi.
Try this...
But is better fix the original dump then it will works.

Best regards.:wink:

[juzek]

Hi.
Try this...
But is better fix the original dump then it will works.

Best regards.:wink:
Thanks juozas10, today is sunny SUNday ;) but on start of the week I will try with dump that You gave me (offcourse now I compared with dump that I made from suspicius ecu - there are lot differecies with bytes structures - at now I for susre that my ecu have invalid eeprom data inside. Once again thanks for Your help.
Regards

[juozas10]

Thanks juozas10, today is sunny SUNday ;) but on start of the week I will try with dump that You gave me (offcourse now I compared with dump that I made from suspicius ecu - there are lot differecies with bytes structures - at now I for susre that my ecu have invalid eeprom data inside. Once again thanks for Your help.
Regards

Hi.
Can you send in post these invalid dump.

Best regards.:top:

[juzek]

Yes, I can. c56 reading from ecu attached below.
Have a nice day juozas10 and all of DK members and viewers.

[juozas10]

Yes, I can. c56 reading from ecu attached below.
Have a nice day juozas10 and all of DK members and viewers.

Please read your corrupted dump again by 8 bit. and post here please.

Best Regards.:top:

[juzek]

Unfortunatelly, it is not possible (memory has been already programmed by me..). You think, that it is my fault by unproper reading (wrong choice of memory structure)? Dump that You gave me must be programmed as 8bit?

[juozas10]

Unfortunatelly, it is not possible (memory has been already programmed by me..). You think, that it is my fault by unproper reading (wrong choice of memory structure)? Dump that You gave me must be programmed as 8bit?

Hi.
Yes I think that is your fault. It's better to not hurry doing jobs like this.

Best Regards.:top:

[Andrey_san]

Hi.
Try this...
But is better fix the original dump then it will works.

Best regards.:wink:

Hello,

Does this works for all MN141500 control modules or just for 2006 year?
I'm asking because I wanna try this dump for Outlander 2003 with the same control module.

Thanks and best regards,
Andrey

[juozas10]

Hello,

Does this works for all MN141500 control modules or just for 2006 year?
I'm asking because I wanna try this dump for Outlander 2003 with the same control module.

Thanks and best regards,
Andrey

Hi.
Try if the car have the same airbag it mite work but mostly there are different.
That's why I'm always telling that you need to fix the original dump.
GOOD LUCK.:bounce:
Best Regards.

[Andrey_san]

Hi.
Try if the car have the same airbag it mite work but mostly there are different.
That's why I'm always telling that you need to fix the original dump.
GOOD LUCK.:bounce:
Best Regards.

juozas10,
I will very appreciate if you help me with fixing my dump.
It is attached.

[juozas10]

juozas10,
I will very appreciate if you help me with fixing my dump.
It is attached.

Hi.
Check again.
Dump is read wrong.
Read again.

Best Regards.

[Andrey_san]

Hi.
Check again.
Dump is read wrong.
Read again.

Best Regards.

Unfortunately, I can't do another initial dump because I've tried to load some other dumps :(
Is it possible to do somethig with this?

Thank you.

[juozas10]

Unfortunately, I can't do another initial dump because I've tried to load some other dumps :(
Is it possible to do somethig with this?

Thank you.

If I understood well, original damp you no longer have.
Try this...
Best Regards.:wink:

[Andrey_san]

If I understood well, original damp you no longer have.
Try this...
Best Regards.:wink:
Thanks a lot. I will try this tomorrow.
Just a quick question:
Driver and Passenger airbags that I have installed are different to original ones (they are from European Outlander 2005 with 4 airbags and my car was made in 2003 for USA with 2 airbags).

May it be a problem?

[Andrey_san]

If I understood well, original damp you no longer have.
Try this...
Best Regards.:wink:
This one works!!!!! :bounce:

juozas10, thanks a lot for your help. Good luck.