help in 406 remote

[spider2004]

i have a problem with peugeot 406 2004 remote
after reprogramming key remote has dead
i tried programming the remote manually but did not work
disconnected battery for a few minutes
but no way ............
pls help
thanks:damnmate:

[ExPro]

Not enough info. Replace battery.

[spider2004]

Not enough info. Replace battery.

i replaced battery---disconnect old battery for a minute and replace it with new one...............but no way

[ExPro]

That's what I mean about not enough information, you didn't mention you replaced the battery.

How did you program the key? How did you manually program the remote?

Do you have access to Peugeot diagnostic machine?

[spider2004]

That's what I mean about not enough information, you didn't mention you replaced the battery.

How did you program the key? How did you manually program the remote?

Do you have access to Peugeot diagnostic machine?


thanks ExPro
i have not Peugeot diagnostic machine
but i reprogram remote manually by this steps:
1. Turn the Ignition switch ON.
2. Press the large Plip key button (Primary Plip)
3. Within 10 seconds, press the large Plip key button (Secondary Plip)
4. If there is one remote, press the Primary plip button twice.
5. Turn ignition OFF.
6. Test Plip?s for correct operation.

[immokill]

hello

try it


406, Xsara and Xantia Deadlocking (2 button PLIP)


Unlock all doors using a working key.

Depress and hold the large PLIP button for 20 seconds while the LED is flashing.

While still holding down the large PLIP button, press the smaller deadlocking button once. The
LED will stop flashing at this point.

Release, and press the large PLIP button once and the LED will extinguish.

Insert the key in the ignition barrel and switch to the ON position, wait 10 seconds then switch to
OFF



406 and 605 Deadlocking (1 button PLIP)
These vehicles are supplied new with a Primary and a Secondary PLIP. There are labelled inside
PRIM or SEC.

Insert the key in the ignition barrel and switch the ignition to ON

Press the large PLIP button for the Primary PLIP.

Repeat for the Secondary PLIP within 10 seconds.

Switch the ignition to OFF.

Regards

[spider2004]

hello

try it


406, Xsara and Xantia Deadlocking (2 button PLIP)


Unlock all doors using a working key.

Depress and hold the large PLIP button for 20 seconds while the LED is flashing.

While still holding down the large PLIP button, press the smaller deadlocking button once. The
LED will stop flashing at this point.

Release, and press the large PLIP button once and the LED will extinguish.

Insert the key in the ignition barrel and switch to the ON position, wait 10 seconds then switch to
OFF



406 and 605 Deadlocking (1 button PLIP)
These vehicles are supplied new with a Primary and a Secondary PLIP. There are labelled inside
PRIM or SEC.

Insert the key in the ignition barrel and switch the ignition to ON

Press the large PLIP button for the Primary PLIP.

Repeat for the Secondary PLIP within 10 seconds.

Switch the ignition to OFF.

Regards

thanks im*okill
3 days ago i tried steps nearly than yours.... steps are:

Procedure
1. Press and hold large button and then press and hold the small button for 20
seconds.
1. Release both buttons, the indicator light on the plip will illuminate.
2. Press the large button once and the light will go out.
3. Switch the ignition ?ON? for 3 to 5 seconds.
4. Switch the ignition ?OFF? and remove the key.
5. Lock and Unlock the vehicle with the remote to test.

[ExPro]

Seems like you've followed the correct procedure - are you sure the remote plip is actually working? Have you examined the circuit board under magnification for broken tracks or connections?

Do you know anyone with Peugeot diagnostic?

[spider2004]

Seems like you've followed the correct procedure - are you sure the remote plip is actually working? Have you examined the circuit board under magnification for broken tracks or connections?

Do you know anyone with Peugeot diagnostic?

thanks EXPRO
a dont know anyone with Peugeot diagnostic

but remote was actually working before reprogramming key with
key programmer......
so i dont think if there is proken connectors or anything els

[ExPro]

I have the diagnostic machine, where are you located? Otherwise...

I am not sure (I have bad recall) but I think in a similar post/problem the advice was to remove key, lock doors manually, disconnect the battery for a short while to reset the ECU, then the programming would work? Worth a try?

[spider2004]

I have the diagnostic machine, where are you located? Otherwise...

I am not sure (I have bad recall) but I think in a similar post/problem the advice was to remove key, lock doors manually, disconnect the battery for a short while to reset the ECU, then the programming would work? Worth a try?

thanks ExPro for great help i am in egypt
i want to ask what battery that should be disconnected is it car battery or remote battery

thanks

[ExPro]

Sorry, yes I meant the car battery to (hopefully) reset the relevant ECU to accept programming. It's just a wild guess but I'm at a loss for what to suggest next.

I nearly forgot, you might need to input the radio code after battery disconnection. Hopefully you have the code?

[bonus2010]

hello

try it


406, Xsara and Xantia Deadlocking (2 button PLIP)


Unlock all doors using a working key.

Depress and hold the large PLIP button for 20 seconds while the LED is flashing.

While still holding down the large PLIP button, press the smaller deadlocking button once. The
LED will stop flashing at this point.

Release, and press the large PLIP button once and the LED will extinguish.

Insert the key in the ignition barrel and switch to the ON position, wait 10 seconds then switch to
OFF



406 and 605 Deadlocking (1 button PLIP)
These vehicles are supplied new with a Primary and a Secondary PLIP. There are labelled inside
PRIM or SEC.

Insert the key in the ignition barrel and switch the ignition to ON

Press the large PLIP button for the Primary PLIP.

Repeat for the Secondary PLIP within 10 seconds.

Switch the ignition to OFF.

Regards


Just wanted to say a BIG THANK YOU for your extremely useful post. I programed a 2 button plip key for a Peugeot 406 today. Unfortunately afterwards, I couldn't get the remote plip to work, despite following the instructions given in the manual for the key programmer (similar to instructions posted earlier in the thread.)

YOUR instructions worked 100% - so if anyone else has the same problem with a 406 year 2000 - we now know the right method - thanks to you.
Cheers.

[Ashraf6119]

Hi,

Sorry, But, can you just double check the Battery in your Remote Fob if you have not inserted wrong way.

There for there are NO signal from the remote.

Hope This Helps.

Ash


PS: Bonus2010 Thanks for giving feedback.....................