View Full Version : 2003 Corsa Lost wheel locking key
justy22
26th May, 2010, 07:26 PM
Hi All
2003 corsa needs cv joints and rear wheel bearing doing can i do these without taking wheels off as the wheel locking key is lost and the locking nuts have the revolving outer on it so i cant hammer a socket onto it to get it off
All help appreciated please
Ashraf6119
26th May, 2010, 07:41 PM
Hi
If they are the original one fitted than you get the replacement key from the Dealer from your Vin Number.
Ash
dafdiagnos
26th May, 2010, 10:07 PM
if not, use a cobalt drill bit & stud extractor
Meat-Head
26th May, 2010, 10:24 PM
YouTube - Locking Wheel Nut Remover - DYNOMEC
M-H-M when we go 'shopping' simply split the 'outer jacket' with an old unloved screwdriver, then use the 'spiral' type nut remover.
Did you jump start this car as well and lost the milage?
cactikid
26th May, 2010, 10:27 PM
yes makes it awkward,dont leave it too late to get a tool to remove the wheel as a flat is looming very close,if not dealer auto shops may know your make and even some dealers have a box of multiple fitments.
cactikid
26th May, 2010, 10:32 PM
MEAT-HEAD-MOTORS WILL BE CLOSED FOR
'STAFF TRAINING' ON FRIDAY 28TH MAY 2010
you buying??lol
Meat-Head
26th May, 2010, 10:35 PM
MEAT-HEAD-MOTORS WILL BE CLOSED FOR
'STAFF TRAINING' ON FRIDAY 28TH MAY 2010
you buying??lol
Sometimes you wish you hadn't started something, you say that.
EVERY BODY around the Meat-Head-Motors area have all said the same thing, along the lines of "Nice knowing you" "Don't get gang ra*ped"
"when you coming back" etc
fahadn
26th May, 2010, 10:49 PM
check on ebay for the unlocking bolt
justy22
27th May, 2010, 02:36 PM
YouTube - Locking Wheel Nut Remover - DYNOMEC (http://www.youtube.com/watch?v=GFXfEhTi8VU)
M-H-M when we go 'shopping' simply split the 'outer jacket' with an old unloved screwdriver, then use the 'spiral' type nut remover.
Did you jump start this car as well and lost the milage?
Ordered one of these look very good
justy22
27th May, 2010, 02:44 PM
Hi
If they are the original one fitted than you get the replacement key from the Dealer from your Vin Number.
Ash
This i s a Myth i'm afraid no data for the locking wheel nut is associated with the vin number, the lockers are put on at the dealers, dealer said i could take a clear pic of the nut and they would forward onto the lock company
justy22
27th May, 2010, 02:58 PM
also like to mention these are tempered steel cannot be drilled or split the outer ring with a hard chisel is near impossible only hope is the dynomec tool or a match from the pic i sent to the dealer
ZIE
27th May, 2010, 05:54 PM
FRANKLIN SECURITY WHEEL LOCK LOCKING NUT REMOVER AFT25 on eBay (end time 05-Jun-10 22:22:16 BST) (http://cgi.ebay.co.uk/FRANKLIN-SECURITY-WHEEL-LOCK-LOCKING-NUT-REMOVER-AFT25-/380237266710?cmd=ViewItem&pt=UK_Measuring_Tools_Levels&hash=item5887e83f16)
This is for a similar tool as the dynomec but made by franklyn, could do the job..
Powered by vBulletin® Version 4.2.5 Copyright © 2024 vBulletin Solutions Inc. All rights reserved.