VW Polo 2008 dump for Magneti Marelli

[Flooodi]

Hi friends,
I need full dump (flash+eeprom) for a dash Magneti Marelli 6Q0920823T. The car is a Vw Polo 2008 1.2 BME. Inside I have a motorola HC9S12H256 which now is broken. I've already ordered HC9S12H256 but I need full dump.
Thank you very much!

[Tetris]

Hi friends,
I need full dump (flash+eeprom) for a dash Magneti Marelli 6Q0920823T. The car is a Vw Polo 2008 1.2 BME. Inside I have a motorola HC9S12H256 which now is broken. I've already ordered HC9S12H256 but I need full dump.
Thank you very much!

Yesterday I received a dump of its panel ( Polo Magneti MC9S12H256 ) device UPA-USB, I magician send it to you, I need a pin out of this panel can help me with this. At least say what program I can see the pin

[Flooodi]

In the attachement you have the pinout for reading motorola. It is not secured and it would be best to read flash and eeprom it with ETL . If you don't have ETL you can use UPA but you have to set oscilator to 6000.

orange=+5V
white=reset
black=gnd
violet=BKGD/BDM

Best regards!

[Tetris]

In the attachement you have the pinout for reading motorola. It is not secured and it would be best to read flash and eeprom it with ETL . If you don't have ETL you can use UPA but you have to set oscilator to 6000.

orange=+5V
white=reset
black=gnd
violet=BKGD/BDM

Best regards!

At me 3 panels from Polo 2007 Marelli, 2 -2006 years and one end 2007. With UPA at me it has turned out to read through the panel of 2007, I spread here it damp.
But two other panels (identical with this MC9S12H256CVF) UPA does not read, writes mistakes are not present but also data are not present everywhere FF.
Can you know in what business, I do all as with this and that it is impossible
I am necessary to me pin im*o for damp which has laid out you can tell to me it?

[Flooodi]

Unfortunately the content of the eeprom is incomplete and the flash is missing. Can you try to get a full reading of the processor with something else than UPA?

[Tetris]

Unfortunately the content of the eeprom is incomplete and the flash is missing. Can you try to get a full reading of the processor with something else than UPA?

i have programmer 1,54 (chinese clone) but with it i cannot do anything. are there some tricks to read it? the file i get with the programmer is about 265 kb, but it is something complete different from the data i've sent yo? (upa).

can you please help me to find the immo pin from the data i've sent you?

is it possible that upa doesn't read other panals because they are closed? and can I open them with the programmer 1,54?

[Flooodi]

Try to read the eeprom again with upa and from the line 800 to FF0 you will have to see FF not 00.

[Tetris]

Try to read the eeprom again with upa and from the line 800 to FF0 you will have to see FF not 00.

its 23 oclock now here so i will try it tomorrow and write you

[Tetris]

Try to read the eeprom again with upa and from the line 800 to FF0 you will have to see FF not 00.

Damp from 800 bis FFF0

[Flooodi]

I've found an complete eeprom for my cluster, now I need a good flash. Thank you!

[polat]

NO UPO ELRASOFT
(*) IS READING WRONG

ETL READ SMOOTH DAY IS READING

(REMOVE RESET)

[polat]

NO UPO ELRASOFT
(*) IS READING WRONG

ETL READ SMOOTH DAY IS READING

(REMOVE RESET)

OK KM

[Flooodi]

Thank you for the dumps but you forgot to activare the flash reading so I've found only the eeprom in those files. Can you read the entire content? Best Regards!

PS the dump is from 6Q0920804J ;) but the flash should be the same with the one that I need.

[Flooodi]

I've found the dumps but unfortunately the eeprom from 6Q0920823T it's from a car with ABS (my car doesn't have ABS) so my speed indicator it's on 0km/h all the time and also my steering pump it's not working well because it's not reading the speed of the vehicle.
In conclusion I'm still looking for a 6Q0920823T eeprom from a car without ABS or, if anyone knows, which is the value that I must modify in the dump to run well.
Thank you very much!

[aminebot]

deleted.....

[potatodog]

This is wrong! The CAN-gateway (19) is integrated into the Cent. Elect. (9).
He could try a dump of the dash with an automatic transmission. This get the speed-signal not from ABS

[aminebot]

deleted.....

[potatodog]

to be sure , disconnect dash and try to connect to gateway (19)

is available... and now?:devil:
sorry but I know what I'm writing

[aminebot]

is available... and now?:devil:
sorry but I know what I'm writing

Sorry i mad mistake , yes gateway module is into Central electric for this model.