Alex789
15th June, 2010, 11:22 PM
I moved this post here as structure of forum was being changed.
Hello.
Toyota Prado 2003 3RZ-FE. All keys are lost.
I performed immo reset with Toyota commander and immo lamp in dash is constantly on with ignition off (programming mode). I try to adapt single chip ID-67. When ignition is switched on, immo lamp remains on 5 seconds and then starts to flash evenly (transponder is correct). A waiting in such state for 30 mins with following 5 times ignition switching on/off during 5 sec (end of procedure) doesn't help. Short link between 4 and 13 pins of OBDII with 30 mins waiting and ignition on doesn't solve problem also.
I took off immo box and ECU and found in immo dump that data of old keys still presented excluding page 2 which was exchanged with value "AC" for all 3 keys. I put 2 new master keys, which i read with Tango programmer, and sub key (extracted from other (internet) dump) in immo dump. Comparing my immo dump with another one (downloaded from internet) for such 2003 3RZ Prado vehicle, i found differences in last five rows. In ECU dump these keys should be presented in other form.
Can any body check my corrected immo file and explaing how to put new keys in ECU dumps. I understand that if immo will be correct then 4/13 procedure can be applied, but want to complete this job on the table.
Files are enclosed.
Thanks and regards.
Read with Tango two ID-67 locked chips (masters according page 1).
**********************************************
Key 1 (master)
Page 1 - 32
Page 2 - 4A
Page 3 - B26045 14
Data stream - 7E 32 4A 14 45 60 B2 06 3B 35
Key 2 (master)
Page 1 - 32
Page 2 - 4A
Page 3 - B25925 14
Data stream - 7E 32 4A 14 25 59 B2 06 6F B6
Last 5 rows of another dump of Prado 2003 3RZ-FE.
0x1B0 FFFFFFFFFFFFFCEF FCEFFCEFFCEFFCEF
0x1C0 FEFEFEFEFEFE0303 0303030323352335
0x1D0 233523352335FFFF FFFFFFFFFFFFFFFF
0x1E0 FFFFFFFFFFFFFFFF FFFFFFFF78787878
0x1F0 FFFF00FFFFFFFFFF FFFFFFFFFFFFFFFF
Hello.
Toyota Prado 2003 3RZ-FE. All keys are lost.
I performed immo reset with Toyota commander and immo lamp in dash is constantly on with ignition off (programming mode). I try to adapt single chip ID-67. When ignition is switched on, immo lamp remains on 5 seconds and then starts to flash evenly (transponder is correct). A waiting in such state for 30 mins with following 5 times ignition switching on/off during 5 sec (end of procedure) doesn't help. Short link between 4 and 13 pins of OBDII with 30 mins waiting and ignition on doesn't solve problem also.
I took off immo box and ECU and found in immo dump that data of old keys still presented excluding page 2 which was exchanged with value "AC" for all 3 keys. I put 2 new master keys, which i read with Tango programmer, and sub key (extracted from other (internet) dump) in immo dump. Comparing my immo dump with another one (downloaded from internet) for such 2003 3RZ Prado vehicle, i found differences in last five rows. In ECU dump these keys should be presented in other form.
Can any body check my corrected immo file and explaing how to put new keys in ECU dumps. I understand that if immo will be correct then 4/13 procedure can be applied, but want to complete this job on the table.
Files are enclosed.
Thanks and regards.
Read with Tango two ID-67 locked chips (masters according page 1).
**********************************************
Key 1 (master)
Page 1 - 32
Page 2 - 4A
Page 3 - B26045 14
Data stream - 7E 32 4A 14 45 60 B2 06 3B 35
Key 2 (master)
Page 1 - 32
Page 2 - 4A
Page 3 - B25925 14
Data stream - 7E 32 4A 14 25 59 B2 06 6F B6
Last 5 rows of another dump of Prado 2003 3RZ-FE.
0x1B0 FFFFFFFFFFFFFCEF FCEFFCEFFCEFFCEF
0x1C0 FEFEFEFEFEFE0303 0303030323352335
0x1D0 233523352335FFFF FFFFFFFFFFFFFFFF
0x1E0 FFFFFFFFFFFFFFFF FFFFFFFF78787878
0x1F0 FFFF00FFFFFFFFFF FFFFFFFFFFFFFFFF