View Full Version : Problem drivers cmd 1251 clone
psico
30th June, 2010, 12:06 PM
hello, can help with installation and configuration of my cmd 1251?
when I install the drivers map3dob recognize me, but I go wrong "usb serial port", and tells me he can not find the drivers, other drivers needed to run the cmd 1251 obd?
thanks
carsolution
6th July, 2010, 08:19 PM
Hi friend.
I can give you the update for the 1255.
Please, give a call and I can do it to you using remote control, Team Viewer if you have it.
Regards,
Nuno
oep
22nd November, 2010, 01:15 AM
Sorry for bringing this thread alive..
I got one from china, and it not working.. usb-to-serial.
I flashed .ept ft232Rl, but even when i put +12 and gnd to interface and use un_mpcprog_can_1251nokiller
it does not shows even power/battery status.
Glued all over, anybody knows is 68hc11 erased or just ept? or solution?
gagula
22nd November, 2010, 01:20 AM
who can help me register MpcProg 1251 protected?
thx
oep
22nd November, 2010, 01:24 AM
who can help me register MpcProg 1251 protected?
thx
If its chines, don't use other software or you will write exact same as i did in post above!
THis goes to all other members.
Chines 1251, not working with:
BDM v1251.exe file size: 6.29Mb.
gagula
22nd November, 2010, 02:08 AM
mine is around 2.5 MB
oep
23rd November, 2010, 07:33 PM
Did anybody did this:
Edc16 u34 on bench with this CMD obd2?
Diagnostics on vcds works ok, k1, k2, can ok.
On CMD soft, battery ok, but its saying to connect k-line (its already connected), but it doesn't connect...
Maybe interface is not ok?
Phhh? :|
cammy25
25th November, 2010, 08:31 AM
Ask Mr Wang:thefinger:
if you use CMD CAN clone its only CAN!!
if you use CMD EDC16 FLASHER clone its only K-line.
CAN on table is only possible with GAteway attached and KL15C ON.
oep
25th November, 2010, 02:11 PM
I got the point, this is CMD CAN Flasher V1251 obd2 - so i guess only can line exists..
But anyway diag via can should work also, and its not.
Vagdashcan also doesn't work on bench.
ps. mr.wang is pussy :)
thanks cammy
danielm
20th March, 2011, 11:24 PM
Hi,
Someone has written with CMD1251 CAN OBD a file BDM in CDTI EDC16 C9 +??
BR
dougydoug
28th March, 2011, 07:45 PM
Ask Mr Wang:thefinger:
CAN on table is only possible with GAteway attached and KL15C ON.
hi; what do you meanby using this sentence? Could you do a tuto please in order to help? many thanks;
znoki
22nd March, 2012, 02:05 PM
Ask Mr Wang:thefinger:
if you use CMD CAN clone its only CAN!!
if you use CMD EDC16 FLASHER clone its only K-line.
CAN on table is only possible with GAteway attached and KL15C ON.
Hi,
Where can I get CMD EDC16 FLASHER K-line clone cable?
I found only CMD CAN everywhere. :(
Thx!
znoki
24th March, 2012, 10:30 AM
If somebody has ept and eeprom files for EDC16 Flasher, it's also helpful, can't find on forum.
tagar
26th July, 2012, 12:19 PM
looking also for CMD flasher k-line ept... anyone? i already have the can bus and working good.
carradio2001
27th July, 2021, 05:15 PM
It is that possible to make CMD 1251 CAN <--> USB to work on k-line ?
BR,
Carradio2001.
Powered by vBulletin® Version 4.2.5 Copyright © 2024 vBulletin Solutions Inc. All rights reserved.