Volvo V70 Dashboard problems/questions

[3ndvi3h]

Hello,

someone here who knews how to power up the following
Volvo dashboard?
The following numbers I can find on the backside:
0839463
8637993
8602471
2248
69294-620T

14 Pin green connector

Pin1: +12V
Pin14: Gnd

Pin1 + Pin14 are for voltage supply, but I think
it must be wake up by CAN.
Which messages must be send?
Someone have a CAN-Logfile off these car?

Thanks in advance

[z786]

have u tried this?

[3ndvi3h]

Hi,

yes this iss the power supply and I tried it.
But in this state its waiting for the right CAN messages...
(I think it needs Kl.15 over CAN).
But I dont know what I should send...

If you only connect power supply, the current is 40mA and
no light is flashing...

Can someone send me a logfile from that car?

[3ndvi3h]

No one can help me :idea:

[matarelec]

i think that 40 mA current is not enough,please try to use a 12 voltes power supply with current 3A at least.I use 5A

[tachonow]

Without Can wakeup the dash dont light even with 10A current power source. Maybe using Can analyzer some results must rise.

[3ndvi3h]

Hi,

I'am using a power supply with 10A...thats not the problem.
I got Canaylizer too, but I don't know what I must send.

Volvo uses 29Bit Identifier with 125kBit/s.

[gizmo666]

did you resolve this? I have same problem my self, i like to wake up dash on the bench..

[cater50]

Hi !!

I'm too trying to power up a dashboard on VOLVO v70 but nothing.

After powering up the 12V, the dashboard sends some Can Frames during 2 or 3 seconds ; and after nothing.
I Think it's waiting for Start Frame (Can messsage).

Is there anybody succeeding in ?

A way should be to take frames on the physical car with obd plug and a can analyser. And after, isolate the right message.
But I don't have the car close to me.

Help should be nice ! ;-)

[dc2sirg]

what year v70?

[cater50]

Hi DC2Sirg ,

That's a V70 of 2001

[garageozcar]

hi
i have also try to but no succes
how to repair this dashboard ??,

[gizmo666]

I wonder if someone have try to trace can messages with upa-can analyzer? is it possible??

[gizmo666]

i am sure at here is someone who knows;)

[Nicko_d]

No need power up it on table...
I always did it in car.....
.

[cater50]

Last time agp, i did it in blind mode, without powering up on table.

Sure, u need to copy for example can frames on a Volvo v70 to power up it.

gizmo666 (http://www.digital-kaos.co.uk/forums/members/97315-gizmo666/) : U're coming from sweden/finland, so, common car no? Easy to find it & copy can datas on obd ?

[soxten]

You ned Canbus connections + power, ex Canbus****yzer
Record from car and then you can do bench testing.

Volvo has diffrent canbus signals and I think 99-01, 01-02, 03-04,05-06,07-08
notice 2001 has 2 diffrent on same year.

[ghauman]

340194



Try This with uucan

Downloaded it a while ago from DK, never tried it.
If it works please share connections to dash..


Regards.

[gljuk]

Sorry please. Does somebody have CAN BUS wake or keep alive message dumps? Need to power up XC90 audio module on the board.
Thank you!

[simensi]

http://www.codecard.lt/carprog/software/emulators/s3-1-volvo-instrument-cluster-can-bus-emulator-for-dash-testing-on-the-table/prod_1032.html

[gljuk]

That was a good point. I have already an alternative tool. It supports 2002...2003 DIM units only. It would not be a good spending of money due to Wife factor. Any advices would be very appreciated. I could also pay for information. Just need to get ICM working on the board. Years: 2004...2005.

Thank you!

[killer85]

CHECK MY TOOLS :)

[Johnner]

Killler, c'mon mate,you know the rules....Post them without the phone numbers in there....

Thank you...

[killer85]

codecard all advertiseand I can not recommend my tool :/

[Johnner]

You can recommend your tools,WITHOUT the phone numbers in your face as you watch these videos...