Suzuki Swift 07 Clear Please

[chaoren]

Hi guys,
I am really new at this but I have been reading heaps.

I have purchased UPA-USB, removed 95160 from 38910-62J02-000 module, read contents and posted here for your help.

Can someone please provide clear code ASAP?

I have heaps more questions but this is a start.

cheers

[juozas10]

Hi guys,
I am really new at this but I have been reading heaps.

I have purchased UPA-USB, removed 95160 from 38910-62J02-000 module, read contents and posted here for your help.

Can someone please provide clear code ASAP?

I have heaps more questions but this is a start.

cheers

Hi.
Try...
Dump cleared.
Please report.
Password is in your pm.
Best regards.:wink:

[chaoren]

Thanks heaps. Your are a legend.
My soldering ability sucks though. Programmed chip OK but broke pin off when trying to put back on module. I created a solder leg but airbag light would not go out in car.
Is there another way to program? Can I solder wires from chip on module to UPA?

I have another module 38910-62J00-000. Would your clear code work on this as well so I can try again.

Thanks

[chaoren]

I have also found a 38910-62J01-000 also from Swift. Will clear work on this also.

[chaoren]

So far I have stuffed 4 eeproms from 4 modules. Lucky my local wrecker has another 5 I can play with.
I have ordered 25 new 95160's from Farnell so I hope I will get something working soon.

Can anyone please confirm if the clear.bin for the 62J02 will work with the 62J00 and 62J01? I can provide more info if required but not dumps as I stuffed the chips.

Thanks

[juozas10]

Can anyone please confirm if the clear.bin for the 62J02 will work with the 62J00 and 62J01? I can provide more info if required but not dumps as I stuffed the chips.

Thanks

Hi.
Try...should work.

Best regards.:thrasher:

[chaoren]

OK. After much learning (especially soldering), I don't think the clear code is working.
I found it too difficult to remove chip from module, solder to UPA, remove from UPA and solder back to module so I purchased new eeproms.
I also purchased a new UPA because the first one seemed faulty.
Now eeproms program and verify OK. Soldering also seems fine but airbag light remains on.

Can anyone help with another Clear code or am I doing something wrong???

[daviee]

Please c lear this file.
I try several methode,but no luck :-(

thank you

[churry]

Hi.
Try...
Dump cleared.
Please report.
Password is in your pm.
Best regards.:wink:

hello juozas10.

i have the sam unit airbag to clean

you give the password file to test the clean file

thanks

[churry]

OK. After much learning (especially soldering), I don't think the clear code is working.
I found it too difficult to remove chip from module, solder to UPA, remove from UPA and solder back to module so I purchased new eeproms.
I also purchased a new UPA because the first one seemed faulty.
Now eeproms program and verify OK. Soldering also seems fine but airbag light remains on.

Can anyone help with another Clear code or am I doing something wrong???


hello chaoren

several things can happen,

although you have soldered the pins are well desoldered check it and look through the magnifying glass.

are not valid reading from one unit to another, unless you have the machine dianostico brand of car.

or there is no communication with the drive of the car.

note:

have resolved the airbag unit 38910 switf suzuki-62j02-000
(5wk43538)
and I need the clean file

if you clean the file of the airbag unit can send by private message or email (javiercj@hotmail.com) thanks

if you need anything alerts

[cseko]

HI
please help me this dump
Suzuki 38910-62j02-000
siemens 5wk4 3538 inside 95160.
thanks
cseko