ford fusion 2006 dash

[pinky1970]

hi there just open up the cluster and can find the 24co8 chip, there are 2, 8 pin chips. the first is 6250g0626 and the second is tja1040 tried to connect to both each time getting gernall reading fault. help any ideas, tacho ask 24c08 or 912, i only have guide for 24c08, uni Tacho 2008.

can anyone help please:egg:

[tachonow]

hi there just open up the cluster and can find the 24co8 chip, there are 2, 8 pin chips. the first is 6250g0626 and the second is tja1040 tried to connect to both each time getting gernall reading fault. help any ideas, tacho ask 24c08 or 912, i only have guide for 24c08, uni Tacho 2008.

can anyone help please:egg:


Try to look up for 912 mcu.

[pinky1970]

how do i do that, i do have a mc9s12 big prosseser chip on the board.

[pinky1970]

when reading the other 8 pin chip, it comes up with reading error, when i press stop it show 94500 km, when the car is 84000 km

[lupu_sandu]

Car type: Ford Fusion - MC9S12H256 - 2006 year
Forget about Tachouniversal. UPA or XprogM will save u

[Ding-Dong]

Car type: Ford Fusion - MC9S12H256 - 2006 year
Forget about Tachouniversal. UPA or XprogM will save u


we can also use the the TACHO to do this type also
done many ...........
but it will not let u save the DUMP from the Processor
the safest way to do is to use the Elrasoft's upa-usb

regards
:rock:

[tim688]

It would be very advisable to read up carefully any manuals you might have about your diga before having a go at this type of processor. If you were trying to read other devices on the board that happen to look like 8 pin eeproms you can consider yourself very lucky not to have corrupted them or completely blown them.
And another big difference is - the vehicle immobiliser data is in this cluster and if that data is lost or corrupted, it's a very expensive trip to the Ford garage on a breakdown truck
All these Ford Focus/Fiesta/C-max type clusters made by VISTEON changed to 9s12 around 2005 and don't store the mileage on eeproms. Good luck!

[diga1]

i have done focus and fusion vith diga 9s12 procesor it vorks 100%
but you have to have 912 dongle that vorks

[pinky1970]

i have a 912 dongle that works, but i have no idea where to connect to, do you have a picture and guide where to connect 912 dongle to the cluster board.

[drpeter]

i have a 912 dongle that works, but i have no idea where to connect to, do you have a picture and guide where to connect 912 dongle to the cluster board.


Let me help you..

COnnect 912 dongle like picture, if you can't read right value with diga, save dump with 912 tools and post dump with actual mileage here.

[pinky1970]

Many thanks Drpeter, you are a life saver. i have three questions first on my uni Tacho under ford fusion its shown 9s12 do i connect 912 cable or the Dongle 912 ?. second do i need to bridge the Quartz ? third being if it showns the right value, can i then ajust new km or do i have to save dump then reload, can you tell me the process please.

[Ding-Dong]

Many thanks Drpeter, you are a life saver. i have three questions first on my uni Tacho under ford fusion its shown 9s12 do i connect 912 cable or the Dongle 912 ?. second do i need to bridge the Quartz ? third being if it showns the right value, can i then ajust new km or do i have to save dump then reload, can you tell me the process please.

with diga or tacho
u wont be able to save the dump from the 9s12 processor
so be very careful ......

regards

[pinky1970]

ok so which do i use dongle 912 or 912 cable ?

[drpeter]

Many thanks Drpeter, you are a life saver. i have three questions first on my uni Tacho under ford fusion its shown 9s12 do i connect 912 cable or the Dongle 912 ?. second do i need to bridge the Quartz ? third being if it showns the right value, can i then ajust new km or do i have to save dump then reload, can you tell me the process please.

You have to connect the 912 dongle, the nubers on the picture are dongle numbers. If it reads the right value then you can program, you can save also the dump with diga no problem.

don't bridge the quartz.

[pinky1970]

sorry to be a pain, but do i have to save the dump to reprogram or if it reads correct value can i just click on ajust km and enter new value.

[drpeter]

sorry to be a pain, but do i have to save the dump to reprogram or if it reads correct value can i just click on ajust km and enter new value.

If it reads the correct value program and job done. If not save with 9s12 tools then post dump here.

[almeida]

hello
don?t be in panic.
if you read the right value you can adjust for the new value.

[pinky1970]

Let me help you..

COnnect 912 dongle like picture, if you can't read right value with diga, save dump with 912 tools and post dump with actual mileage here.

Ok, what do I do with the red wire from 912 dongle. Do I connect that anywhere . Or do I just leave the red alone.

[pinky1970]

Thanks, one last thing, on the dongle 912, its has a red wire do I connect that anywhere or leave it alone.

[pinky1970]

If it reads the correct value program and job done. If not save with 9s12 tools then post dump here.

Ok on the dongle 912 it also has a red cable what do I do with that connect it anywhere or leave it alone this time. Thanks for all your help on this

[almeida]

my friend,
if at pdf you don?t see the red wire connect anywhere, leave the red wire at you pocket and not toucht the red wire anywhere.......
:thrasher:

[pinky1970]

Thanks everyone, Fusion is now done.

[diga1]

thanks good it is done (ha ha ha)

[88diablo]

Hi, I saw the photo for wiring to the 9s12 on an earlier post and I know this is for a fusion but does anyone know if this is the same for a 2008 "57" fiesta visteon and if not does any one have a similar photo of where to connect the 912 dongle for fiesta.

Thanks in advance

[wurz]

Hope this helps

[sejoo]

These is bester forum on the world Thx