PDA

View Full Version : kwp2000 no ecu found problem



magnacin
20th July, 2010, 11:51 PM
Hi,
I just got this KWP2000 plus. i nstalled it and try to read 206 1.6 Bosch 7.4.4 ecu and it starts ok but when i get the point to read ECU I press info and after a while the programs sends a message ECU not found.
Can someone please help me finding the solution to my problem so I can read ECU?
Thanks

rsibiza
24th July, 2010, 01:54 AM
Hi,
I just got this KWP2000 plus. i nstalled it and try to read 206 1.6 Bosch 7.4.4 ecu and it starts ok but when i get the point to read ECU I press info and after a while the programs sends a message ECU not found.
Can someone please help me finding the solution to my problem so I can read ECU?
Thanks


Maybee you ecu cannot be read by KWP or cant be read serial.

There are also some interfaces,they can read some more car,then another interface...first check if you car is in carlist from KWP and then see what to do

gixerke
30th August, 2010, 09:31 PM
Hi.

I try read the audi a6 2.5tdi ecu with kwp2000+, but read the ecu info, but not read the ecu flash (Ecu not founf)! Which is the fuse i take out?
I'm sorry, my english is not good!

gixerke
30th August, 2010, 09:51 PM
Hi.

I tryed flashing the audi a6 2.5tdi 2001, but not read the flash! I trying for kwp2000+, read the ecu data, but not flashing! (Ecu not found)
Which is the fuse take out?

Thanks



Gixerke

I'm Sorry for to the two message!

gixerke
25th September, 2010, 07:47 PM
HI.


I tried read the audi a6 2.5tdi v6 ecu, get ecu info, but not read the flash! I tried with galetto and kwp2000+!

aidyk
26th September, 2010, 01:29 AM
2.5tdi uses a 29f800 chip and apparently this is why it cant read/write etc
i had same problem with both tools few years back on 2.5tdi audi..! best to remove from ecu and read/write in programmer..

good luck

rsibiza
26th September, 2010, 05:11 AM
2.5tdi uses a 29f800 chip and apparently this is why it cant read/write etc
i had same problem with both tools few years back on 2.5tdi audi..! best to remove from ecu and read/write in programmer..

good luck


I never had problems reading or writing 29F800:sleep:

gixerke
26th September, 2010, 09:54 AM
This is a 2001 audi a6 I think is should work!
Which box read this ecu, because i did not to want remove the ecu?!
One of the fuse needs to remove? I remove the 5,15 fuse but not read!

rsibiza
26th September, 2010, 10:12 AM
This is a 2001 audi a6 I think is should work!
Which box read this ecu, because i did not to want remove the ecu?!
One of the fuse needs to remove? I remove the 5,15 fuse but not read!


Fuse 11 should do it.

MPPS reads also without removing Fuse

gixerke
26th September, 2010, 02:00 PM
11 fuse is not include this fuse box! I don't remove this fuse :)

Then i soldering this flash and programinng with willem.

Thanks

aidyk
26th September, 2010, 02:57 PM
I never had problems reading or writing 29F800:sleep:
with kwp and galleto on 2.5tdi..?
i dont have problem either while i have desktop programmer :motz:

gixerke
26th September, 2010, 03:21 PM
with kwp and galleto on 2.5tdi..?
i dont have problem either while i have desktop programmer :motz:


My friend does not want it that take out!

Yes! With kwp and galleto on 2.5tdi!

sjonv
26th September, 2010, 07:42 PM
try reading on bench, this worked for me with a few times..

hotcoding
9th June, 2012, 11:53 AM
what to do if no fuse nr 11

bobolin4o
9th June, 2012, 12:15 PM
Maybe is a 150Hp engine in this case... with 2x27c010 :)

bobolin4o
9th June, 2012, 12:18 PM
Hi.

I try read the audi a6 2.5tdi ecu with kwp2000+, but read the ecu info, but not read the ecu flash (Ecu not founf)! Which is the fuse i take out?
I'm sorry, my english is not good!
Maybe is a 150Hp engine in this case... with 2x27c010 :)

pablo1971
9th June, 2012, 05:06 PM
YES,i agree,either use mpps with correct settins-i think there is a AUDI-ALLROAD protocol that lists both 29f400/29f800,so you cant go wrong,also if it does fail on the write with a wrong protocol,then with mpps you can recover this ecu easily on the bench....

AGS
10th June, 2012, 06:03 AM
Maybe is a 150Hp engine in this case... with 2x27c010 :)
if with 2x27c010 better use good programmer and compare with with a similar file on the same ECU!

gzk
10th June, 2012, 12:34 PM
Hi,
I just got this KWP2000 plus. i nstalled it and try to read 206 1.6 Bosch 7.4.4 ecu and it starts ok but when i get the point to read ECU I press info and after a while the programs sends a message ECU not found.
Can someone please help me finding the solution to my problem so I can read ECU?
Thanks

M7.4.4 cannot be done via obd only ME 7.4.4
have tryed on a lot of car and discover this diffrence
me = electronic trhottle