Audi A4 2002 Auto/Manual gear exchanging

[Alex789]

Hello.

I have Audi A4 2002 2.0 where auto transmission was exchanged with manual one.



- Using VCDS i recoded CAN in instrument cluster (adaption channel 60 - value 1031 (auto) was altered to 1029

(manual)).

Address 17: Instruments Labels: 8E0-920-9xx-8E2.lbl
Control Module Part Number: 8E0 920 900 HX
Component and/or Version: KOMBI+WEGFAHRS. RB4 D28
Software Coding: 00001
Work Shop Code: WSC 37600
Additional Info: WAUZZZ8E32A079773 AUZ6Z0A0193028
VCID: 810366E7A161
2 Faults Found:

01315 - Transmission Control Module
49-00 - No Communications
01316 - ABS Control Module
49-10 - No Communications - Intermittent

-----------------------------------------------------

- In ABS coding was changed from 04279 to 04275

Address 03: ABS Brakes Labels: 8E0-614-517.lbl
Control Module Part Number: 8E0 614 517
Component and/or Version: ABS/ESP front 1726
Software Coding: 04275
Work Shop Code: WSC 00333
VCID: E5CB52775509

18055 - Check Coding of ECUs on Powertrain Data Bus
P1647 - 35-00 - -
18034 - Powertrain Data Bus: Missing Message from TCU
P1626 - 35-00 - -

----------------------------------------------------

- ECU i recoded manually with progger from 11581 to 11501

Address 01: Engine Labels: None
Control Module Part Number: 8E0 909 557 A HW: 8E0 909 057
Component and/or Version: 2.0L R4/5VS 0003
Software Coding: 0011581
Work Shop Code: WSC 00333 935 176729
VCID: 31637627D141
2 Faults Found:

18034 - Powertrain Data Bus: Missing Message from TCU
P1626 - 004 - No Signal/Communication
18057 - Powertrain Data Bus: Missing Message from ABS Controller
P1649 - 008 - Implausible Signal - Intermittent

-----------------------------------------------------

There are no errors in ECU and dash now. In ABS remains fault 18034 only.


Does anybody know where problem remain?

[impolis]

ecu coding not helps, you need flash from ecu, from car with same engine but without automatic transmition. find in etka what ecu code you need and post here. Maybe i or others have from this ecu flash and eeprom and if hardware whill be same like yours ecu its works withaut faults

[Alex789]

ecu coding not helps, you need flash from ecu, from car with same engine but without automatic transmition. find in etka what ecu code you need and post here. Maybe i or others have from this ecu flash and eeprom and if hardware whill be same like yours ecu its works withaut faults

Thanks for info.
My ECU 8E0 909 557A (0 261 207 286) ME 7.5 0003 for auto transmission based on hardware 8E0 909 057.

================ Device N: 1 ================
8E0909557A <- VAG number
PROGRAMMABLE
Program status 0, data status 03
Coding :11581
Part number : 176729
Importeur's number :935
Supplier number : 333
System description : 2.0L R4/5VS


==== SW/HW version
SW version of module 1 : P0000
SW version of module 2 : A4.0.3
Hardware number : 8E0909057


==== Extended identification
--- Flash
Programming succefull - ready for driving.
Programming attempts : 0
Succesful programming attempts : 0
Status of conditions for programming : 0

============================================
18034 Powertrain Data Bus: Missing Message from TCU
Status : Permanent error
missing signal / communication
missing signal / communication
============================================

According to ETKA i need following ECU (manual) - 8E0 909 557 F(X)

[Alex789]

I found flash for VINs from ...8E-2-000001 to ...8E-2-400000 for this engine with manual gear "Audi A4 2.0 ME7.5 130hp ALT 8E0909557 0261207285 sw362543".
My VIN WAUZZZ8E32A079XXX.
I think it's not suitable for me.
If someone has correct flash, pls post here.

[kojoantwi]

:celticparty:

[kojoantwi]

can any body helps me with Basic settings codes for VW,AUDI SEAT AND SKODA Please?

[Alex789]

can any body helps me with Basic settings codes for VW,AUDI SEAT AND SKODA Please?

Which codes do you need? Maybe for DPF filter regenerating, for example, or something else?

[Alex789]

Try this
Ross-Tech Wiki (http://wiki.ross-tech.com/wiki/index.php/Main_Page)

[xoom]

maybe little bit Off topic but can you explain shortly about
Maybe for DPF filter regenerating, for example, or something else?

Thank you

[Alex789]

maybe little bit Off topic but can you explain shortly about

Thank you

I, mean, for example, particle filter emergency regeneration for diesel engine Audi/VW 3.0 TDi which will start under certain conditions and entering login in "[Coding-II - 11]" field in VCDS.

Quote
Particle Filter Emergency Regeneration

Prerequisites:
Ignition ON
Engine ON (Idle)
Oil Temperature above 70 ?C (see MVB 007.2)
Particle Filter Load below 68g (see MVB 104.3)
If the Particle Filter Load is above 68g the Particle Filter needs to be replaced since the car may burn down when regenerating.
Engine Hood CLOSED
Parking Brake ENGAGED
Transmission in (P)ARK
Temperatures at the Exhaust System may rise up to 300 ?C!!!
No Fault Codes Stored
Power Consumers ON (Light, Seat Heating, Front/Rear Window Heater, Climate Control)

The Regeneration may take up to 40 minutes, the engine speed automatically increases to about 1500 RPM.

[Select]
[01 - Engine]

[Coding-II - 11]
Start Regeneration by Entering 10016.

[Do It!]
Quote

Such info you can find at Ross-Tech site.

[branimirj]

I work this car and i read flash dump from a6 2.0 alt engine.regards

[Alex789]

I work this car and i read flash dump from a6 2.0 alt engine.regards

OK. Can you post this dump here with eeprom?

[aaruncee]

Hello.

I have Audi A4 2002 2.0 where auto transmission was exchanged with manual one.



- Using VCDS i recoded CAN in instrument cluster (adaption channel 60 - value 1031 (auto) was altered to 1029

(manual)).

Address 17: Instruments Labels: 8E0-920-9xx-8E2.lbl
Control Module Part Number: 8E0 920 900 HX
Component and/or Version: KOMBI+WEGFAHRS. RB4 D28
Software Coding: 00001
Work Shop Code: WSC 37600
Additional Info: WAUZZZ8E32A079773 AUZ6Z0A0193028
VCID: 810366E7A161
2 Faults Found:

01315 - Transmission Control Module
49-00 - No Communications
01316 - ABS Control Module
49-10 - No Communications - Intermittent

-----------------------------------------------------

- In ABS coding was changed from 04279 to 04275

Address 03: ABS Brakes Labels: 8E0-614-517.lbl
Control Module Part Number: 8E0 614 517
Component and/or Version: ABS/ESP front 1726
Software Coding: 04275
Work Shop Code: WSC 00333
VCID: E5CB52775509

18055 - Check Coding of ECUs on Powertrain Data Bus
P1647 - 35-00 - -
18034 - Powertrain Data Bus: Missing Message from TCU
P1626 - 35-00 - -

----------------------------------------------------

- ECU i recoded manually with progger from 11581 to 11501

Address 01: Engine Labels: None
Control Module Part Number: 8E0 909 557 A HW: 8E0 909 057
Component and/or Version: 2.0L R4/5VS 0003
Software Coding: 0011581
Work Shop Code: WSC 00333 935 176729
VCID: 31637627D141
2 Faults Found:

18034 - Powertrain Data Bus: Missing Message from TCU
P1626 - 004 - No Signal/Communication
18057 - Powertrain Data Bus: Missing Message from ABS Controller
P1649 - 008 - Implausible Signal - Intermittent

-----------------------------------------------------

There are no errors in ECU and dash now. In ABS remains fault 18034 only.


Does anybody know where problem remain?

How you ECU recoded manually with progger from 11581 to 11501 ?