Airbag Logan 8201002828

[vyktorio]

Hi, please somebody can erase crash data from these unit?

TEMIC 8201002828
Dacia Logan

Here is dump from unit

Thanks very much

[juzek]

here is cleared dump for Your Logan, if in car there are everything ok (airbags, pretensioners, etc.) then srs indicator goes off after few seconds when ACC+.
Regards

[amir_82013]

Hi, can somebody erase crash data from these unit?
what program i can use for this?

TEMIC 8200817784
Dacia Logan x90

[vyktorio]

Thanks, i will go try it, after i will write result.

Many thanks

[amir_82013]

Hi, can somebody erase crash data from these unit?
what program i can use for this?

TEMIC 8200817784
Dacia Logan x90

[morfej]

amir_82013: you airbag ECU have sam eeprom 95160 and it you don't know to read such a simple eeprom, you better not do the job at all :)

[aditzi29]

here is cleared dump for Your Logan, if in car there are everything ok (airbags, pretensioners, etc.) then srs indicator goes off after few seconds when ACC+.
Regards

Hi,

If after crush airbags haven't explode just airbag indicator vent on and was cleared with diagnostic tool it's needed to clear eprom from airbag unit ?

[morfej]

If you still have DTC (and you can not clear it) I am afraid that you have to.

[aditzi29]

If you still have DTC I am afraid that you have to.

No DTC was found after clearing with Autel 70x and light is off.
The conclusion: if its an crush and airbag don't explode, DTC from airbag sistem ared cleared and light airbag is off no need to clear eprom from crash data ?

[mad79]

no, if airbag it's ok then you can erase DTC.

[kari11]

Hello Guys:)

My problem is a control unit. I can not find it original dump. I did it, but it does not work.
Please anyone who can help.

[gtservice1]

Hi everybody. I'd like to know what is the best airbag eraser software. What U advice me to use

[drivergabriel]

hey!!! if you have crash data on a renault clio, dacia logan with temic ecu (black box) you can erase it by obd with kkl interface and ddt (witha a pass key). if you need i can put a tutorial.

for this solution you must say thanks also to lupu_sandu

[aditzi29]

It wiil be nice to have a tutorial ! If is more than a simply clear airbag codes with a tool...

Thanks

[hunterirc]

hey!!! if you have crash data on a renault clio, dacia logan with temic ecu (black box) you can erase it by obd with kkl interface and ddt (witha a pass key). if you need i can put a tutorial.

for this solution you must say thanks also to lupu_sandu

It would be very nice to have that tutorial ! Thanks !

[georgegt]

How to obtain the pass key for ddt ?

[isak2009]

Hi dump for Juzek work fine thanks Juzek

[joubliss]

file from Juzek works fine, no need to adaptation just turn to ACC+ and the light goes OFF

thanks

[alex_SW]

hi...what resistance value for driver airbag is needed??
tnx

[hafido1983]

for renault logan
color:red+red+yellow(as gold) and tolerance yellow

[mad79]

It would be very nice to have that tutorial ! Thanks !

[trevormaharaj]

could some please help me remove crash data logan airbag unit 8201 00 28 28 temic

[alfabit]

hi...what resistance value for driver airbag is needed??
tnx

It is written in the service manual, for who wants to read it .

( 2.2 ohm by the way. )

[mimodiag]

hello help my cleare airbag logan 2010 ref: 82 01 00 28 28 temic .

thanks

[ChVlad]

Hi
Try this
Please report
Pass PM

[mimodiag]

no it does not work thank you

[trevormaharaj]

need to change km on 2010 jeep wrangler from 57396 to 34000km please eprom 93rl76

[morfej]

maate ... wrong section.