Alfa Romeo 145 Airbag TRW 60625180

[gujasa]

Hi, Does anyone have a virgin DUMP for TRW 60625180 Alfa Romeo 145?. I cant found nothing in the web. Thanks in advance!

[euroscan]

- only exist 60625181, GTV alfa romeo



Alfa Romeo
43055365 68HC908AS20
46409123 68HC11E9
46538798 68HC11KS2
46813473 68HC908AS60
46813473 68HC08AS32
60625180 68HC11E9
60625181 68HC11E9
60631206 68HC11E9
60651568 68HC11KS2
60655033 04 305536 08AB32
60656767 68HC11E9
60658009 04 305536 08AB32
60663040 04 308087 08AB32
60663943 04 311020 08AS20
60664500 68HC11KA4
60664962 04 305536 08AS20
60665492 04 312040 08AB32
60668390 68HC908AS20
60669249 08AS20
60669250 04 313049 08AS20
60675876 04-320290 08AS20
60675876 04-320290 908AS60
60675880 04 320291 08AB32

[brchip]

Hi guys,

I have this airbag ECU from Alfa Romeo Spider 1996 and I cannot communicate with it.

I'm using this pinout but it's not responding:

9- K line
14- earth
15- +12v

Is the above correct?

Any ideas about what could be wrong? What components should I check?

[euroscan]

- tell us number of this sensor, maybe TRW 60655032.

[brchip]

- tell us number of this sensor, maybe TRW 60655032.

Thank you, euroscan.

The sensor number is 60625181, TRW.

[redtop]

Check out this page for a tool to reset the 60625181 airbag ECU:

Trw2scan - RepairWiki (http://peter-feil.eu/mediawiki/index.php/Trw2scan)

[brchip]

Check out this page for a tool to reset the 60625181 airbag ECU:

Trw2scan - RepairWiki (http://peter-feil.eu/mediawiki/index.php/Trw2scan)

Thanks for sharing that!

I got "Crash data present" and "Pretensioner burst". I could not clear the faults, so does it mean my ECU needs a reset? The car did not crash.

[redtop]

Crash data cannot be reset with this SW. Only error codes.
You need to reprogram the memory by soldering a few wires on the microcontroller.

Sent from my MB525 using Tapatalk

[joe1953]

Hello,
i have the same ecu. I have write clear file but i got the same error.
Is it possible to repair this ecu??

Thanks

[alclot]

Hi everybody! I tried to open software trw2scan with Windows xp and 7 but always it gives me error and close. I installed this driver (http://www.ftdichip.com/Drivers/VCP.htm) to KKL interface. Can anybody help me?
My nightmare!! heheh
Thanks in advance ;)

[brchip]

Hi everybody! I tried to open software trw2scan with Windows xp and 7 but always it gives me error and close. I installed this driver (http://www.ftdichip.com/Drivers/VCP.htm) to KKL interface. Can anybody help me?
My nightmare!! heheh
Thanks in advance ;)

You need to run the trw2scan from a DOS window:

Click start and then type cmd.exe and enter.
Navigate to the correct folder (type CD.. to go up one level and type CD name_of_foler to go inside a folder)

When you get to the trw2scan folder, run trw2scan by typing trw2scan trw2.obd

[alclot]

Hi brchip. Now software works. Thank you. I put wire to ecu but soft gives me error "ECU response time out". Consumption of airbag is 0,02A. is Pinout correct?

[brchip]

Hi brchip. Now software works. Thank you. I put wire to ecu but soft gives me error "ECU response time out". Consumption of airbag is 0,02A. is Pinout correct?

I think it's not correct. It should be more, around 0,150.

PINOUT:

1 and 2 driver airbag (use resistor)
3 and 4 passenger airbag (use resistor)
6 and 7 passenger pretensioer (use resistor)
9 Kline (connect to pin 7 of the diagnostic interface - I use VAG FTDI)
10 and 11 driver pretensioner (use resistor)
13 fault light (use a small 12v lamp) and connect the other side of lamp to +12v
14 earth
15 ignition (+12v)