FLASH PROGRAMING PROCEDURE IN CAT ET

[hercamp]

ELECTRONIC TECHNICIAN (ET) TROUBLESHOOTING - Continued
SYMPTOM

Flash Programming
This is a method of programming or updating the flash file in an engine's Electronic Control Module (ECM). Use
this procedure if original ECM flash files are missing or not available. To update configuration files, Caterpillar Electronic Technician (ET) is used to flash program a file into the memory of the
engine's ECM. If you do not have the flash file, it must be obtained from your Caterpillar dealer.
MALFUNCTION
Personality Module Mismatch. ECM has an incorrect or outdated Flash File.
CORRECTIVE ACTION
STEP 1.
On EMCP, set ENGINE CONTROL switch to OFF/RESET. Set Battery
Disconnect Switch to OFF. Set DEAD CRANK SWITCH to OFF.
STEP 2.
Connect the Cat ET to connector CDC-P7
STEP 3.
Set Battery Disconnect Switch to ON. Set DEAD CRANK SWITCH to NORMAL.
On EMCP set ENGINE CONTROL switch to COOL DOWN/STOP.
STEP 4.
Establish communication between Cat ET and the engine's ECM.
STEP 5.
Select WinFlash from the Utilities menu on Cat ET.
NOTE
If WinFlash will not communicate with the ECM, refer to Troubleshooting, Electronic Service Tool
Will Not Communicate with ECM.
STEP 6.
Program the flash file into the ECM.
a. Select the engine ECM under the Detected ECMs.
b. Press the Browse button in order to select the name of the flash file that will
be programmed into the ECM.
NOTE
The Flash Files are located on a CD provided with the Cat ET software.
c.
When the correct flash file is selected, press the Open button.
d. Verify that the File Values match the application. If the File Values do not
match the application, obtain the correct flash file.
e. When the correct flash file is selected, press the Begin Flash button.
f.
Cat ET will indicate when flash programming has been successfully
completed.
STEP 7.
Turn the ENGINE CONTROL switch to MANUAL START. Check for proper
operation. Repair any active diagnostic or event codes.
WinFlash Error Messages
If you receive any error messages during flash programming, click on the Cancel button in order to stop the
process. Access the information about the ECM Summary under the Information menu. Make sure that you are
flashing the correct file for your engine.


I HOPE THAT HELP YOU

if not just lost time reading:reddy:

[joeseph666]

ELECTRONIC TECHNICIAN (ET) TROUBLESHOOTING - Continued
SYMPTOM
{...}
If WinFlash will not communicate with the ECM, refer to Troubleshooting, Electronic Service Tool
Will Not Communicate with ECM.


Ok... so that has happened... winflash can't see the ecm anymore... what now?

[hercamp]

if cant connect after downloading error. close ignition twice and try to program from new ecm option.

if not will need to see if exist a bench with extra conection data .

[lituzz]

flash file for EMCP3.2??

[lituzz]

Greetings, I have an EMCP3.2 controller on a genset, and I need to flash it. It has the following info:

Part No.: 3007646-01
S/N: 1648B059TA
Software Part No.: 3222198-00
Software Date: NOV2007
Software Description: L1 6_0 Standard -- Spanish, 2.2 Prod, 7Nov2007

Does this mean that the flash file I need is 3222198-00? If so, Can anybody share it? I have on my flash files: 3222197.FLS and 3222199.FLS

Thank you all in advance.

[salwan]

help me i need
eng numb 191-4479
power train numb 175-1171
i need flash file

[salwan]

ECM Part Number 1547443-05
ECM Serial Number 0484D522ED
Software Group Part Number 2456589-00
Software Group Release Date JAN04
Mon Sys Harness Code 23

i need latest flash file of
2456589
please

[amriaali]

thkkkkkkkkkkkkkkkkkkkkk

[jdawg]

when u try to reflash with different flash file in win flash and it wont accept the file, change the interlock code to start with. Put passwords in and then reflas to the file you want then put in passwordsagain and thereyou go

[khadang]

hello all. please help me ho to flash for this ecm.
ecm is blank
thank so much advance!

[jackalfa]

After flashing a 70 pins I get message "Unable to communicate with an ECM!
It doesn't want to connect to either to et or winflash, please any more ideas or some other tricks to revive it?

please help...

[jackalfa]

I connect the the ECM to a cat comm adapter II using CDL protocol and it worked. Problem solved.

[peko]

hi,

can you explain what is CDL protocol ?

thanks ;)