Puegeot Partner Dash Lights Coming On On Their Own

[dik]

The dash lights (stop mileage & handbrake light) come back on a few minutes after switching engine off, if you then lock or open the door they go out for a few minutes then come back on. Other than being french anyone know what's wrong

[Albanais]

Open the BSI and check for traces of water, it happened to me many times.
Cheers mate

[Meat-Head]

Agree with the above, but was going to say check for pig piss.

Have a mooch round the daashboard section, see if you can find the pin outs for the plugs.

work out the ignition feed, then put a SMALL load on it, say 5 KILO-watt sidelight bulbb to make it draw more power

OR

Find the ignition feed, cut this, run to ignition switch via a fuse and stand bak

[dik]

Open the BSI and check for traces of water, it happened to me many times.
Cheers mate Where do I find the BSI and what does it look like

[Albanais]

You can find it underneath the steering column for the left hand drivers, I mean does not mater it is on the left of the car.
Here you have a link for the BSI image http://www.google.com/imgres?imgurl=http://www.metsan.net/cars/bsi/bsi1.jpg&imgrefurl=http://www.metsan.net/cars/car.htm&usg=__e4rM9F0ISG4ewMzaq8O-iK5-ZeM=&h=329&w=273&sz=18&hl=fr&start=0&zoom=1&tbnid=0hrACFj3sN37OM:&tbnh=162&tbnw=143&prev=/images%3Fq%3Dbsi%26um%3D1%26hl%3Dfr%26sa%3DN%26biw %3D1280%26bih%3D838%26tbs%3Disch:1&um=1&itbs=1&iact=hc&vpx=138&vpy=106&dur=6172&hovh=247&hovw=204&tx=152&ty=122&ei=Sey_TMmQJML88AaTjLWMBQ&oei=Sey_TMmQJML88AaTjLWMBQ&esq=1&page=1&ndsp=20&ved=1t:429,r:0,s:0

[dik]

Found this on the web, looks like BSI may be corrupted

Peugeot BSi reboot procedure

Peugeot BSi reboot procedure
Some of you will have already come across a strange problem when programming
keys on 2002 onwards Bsi equipped Peugeot. This usually presents
itself as a complete instrument cluster failure after the keys have
been programmed when the customer comes to collect the car.
BSI Unit
The BSI unit is basically a computer which
handles a multitude of functions such as
odometer value, central locking, lights and
immobiliser. Some later Bsi units are liable
to corrupt their own software program if
not “woken up” in a specific way after
programming keys or battery disconnection.
The details of this are explored
thoroughly in a Peugeot TSB but I will
summarise for you briefly.
Procedure for Initialising the BSI after key learning
1. Disconnect the diagnostic tool.
2. Put the driver’s window down, lift the bonnet and ensure all
equipment is switched off.
3. Ensure all doors are closed and remove key from the
ignition.
4. Wait for 3 minutes, disconnect the vehicle battery and wait
15 seconds.
5. Reconnect the vehicle battery, wait a further 10 seconds (do
not open doors.)
6. Switch on the side lights through the driver's window.
7. Switch on the ignition and check system’s functionality.
8. Hold lock button on key down for 10 seconds.
9.remove key open & close door test c entral locking system
10. Start the engine and complete the system’s check.
Failure to follow this procedure could result in incorrect operation of many
BSI related items.
It did take three attempts following this procedure before it worked.


This is a shorter version of the TSB given to me regarding battery dis-connects on Peugeot Citroen BSi units:
PROCEDURE FOR BATTERY DIS-CONNECTION (The 3 Minute Rule)
Whenever a vehicle battery has to be dis-connected, switch off all equipment, interior lights etc, close the doors leaving the drivers window open.
Switch off the ignition and remove the key and any DIAG equipment.
Wait a full 3 minutes before disconnecting the battery.
The BSi must be allowed to go to SLEEP ie into "power save mode". Do not operate any equipment on the vehicle during this time. Remember, even opening the bonnet will wake the BSi on a vehicle fitted with alarm.
If the battery is under the bonnet, open the bonnet first and leave it up. 807 batteries can be dis-connected through the drivers window, remove floor cover first.
ALWAYS disconnect any DIAG equipment and do not operate any plips from other vehicles during the 3 minute waiting period.
PROCEDURE FOR BATTERY RECONNECTION
Unless otherwise instructed by Peugeot or Product Service, you must always carry out the following procedure, often referred to as a "soft re-boot", to minimise the possibility of the BSi corrupting its own software when reconnecting the vehicles battery supply.
Ensure the procedure for battery disconnection has been adhered to and importantly all BSi functions were switched off with the drivers window left down.
1 Close all doors
2 Remove ignition key if left in ignition
3 Reconnect battery. DO NOT open any doors
4 Wait 10 seconds
5 Switch on healights through the drivers window (you will hear a "bong")
6 Switch on ignition then start the vehicle and check system functions

NOTE: Upon reconnection, if any vehicle function controlled by the BSi i.e . interior light is switched on,the internal operation of the BSi has the potential to spike or corrupt its configuration and software program......


I will try a re boot and see if that fixes it
EDIT didn't fix it