read micronas with x prog

[almeida]

hello,
with xprog, how many wires we need to connect?
do i need to lift some pins?
the job is safe to do with the clone xprog?
thanks

[martin292009]

picture conections... regads:ridinghorse:

[z786]

i know of a few people on here that have read micronas with the clone

[almeida]

hello,
this picture clarify me a lot.
i need a tool to read the micronas.
what you think about the carprog to read micronas by obd?
this works?
some one have experience with that.
cheers

[T72]

hello,
this picture clarify me a lot.
i need a tool to read the micronas.
what you think about the carprog to read micronas by obd?
this works?
some one have experience with that.
cheers
first question, what for you want to read Micronas?

[almeida]

to change the milleage at the vag group......2006 until 2008 +-

[pasonjayne]

to change the milleage at the vag group......2006 until 2008 +-

Buy a ROSFAR R250 clone, Smelecom one works 100% not sure of others though.

[T72]

to change the milleage at the vag group......2006 until 2008 +-
its verry old way to change the milage by soldering, and not safe! This job can do R250(or clone), Xprog-m(clones damaging sometimes).
There are OBD softs on carprog, vagprog, dp3, enigma....its safe and quick way.

regards

[edgarelpro]

HI how I can see the picture I can?t download because my privilage are low

[chriskross]

its verry old way to change the milage by soldering, and not safe! This job can do R250(or clone), Xprog-m(clones damaging sometimes).
There are OBD softs on carprog, vagprog, dp3, enigma....its safe and quick way.

regards

Hello!

i want to change dash from golf v 2008, i have already pin from the old dash read by can+ K com.
can these tools read pin from new dash without have working key?

regards chris

[T72]

Hello!

i want to change dash from golf v 2008, i have already pin from the old dash read by can+ K com.
can these tools read pin from new dash without have working key?

regards chris
no! when immo is activated(no working key) there is no way by OBD, sorry
I think best way is xprog

[chriskross]

what are you thinking about this

you can read but must modify eeprom manualy to work without key
read and save original dump
erase dump block 0x810 0x91f now you will see def on display but key not required
load original dump and write it via diag to dash now
when original restored use read immp to get pin :bounce:

[waldi1979]

24C32 or Micronas EEP???

[autofan1965]

External 24c32 memory, you can write just dump from another dash.

[waldi1979]

I have Smok X-can.
I write dump from another dash. I have DEF on display, i write ori EEP but acces error....

[Mario3]

I have Smok X-can.
I write dump from another dash. I have DEF on display, i write ori EEP but acces error....
you probably have non paired key in ignition while trying to make anything thats why you get the errors. There are some versions that CAN be done even if immo active, and there are some where is no way to make anything via OBD while false key in ignition. Tried with XCAN, and digiprog3 and Super Vag 2.0

when working on madeable version all 3 are working, same when trying on version that can not be done

regards

[autofan1965]

I have Smok X-can.
I write dump from another dash. I have DEF on display, i write ori EEP but acces error....

Read original, write from another dash, press change km, put any value, wait until it will be flashed then use write eeprom button and write orignal content. From this point you have full access to dash.