View Full Version : Vito immo and start error problem
clauberty
4th November, 2010, 02:06 PM
i will go mad :motz:this is my firs one but it drive me crazy
first i red immo with digimaster mask 0J66D loaded the eerpm in start error v1.3
Amount off prog key 148 is displayed :hmmmm2: something is not right
al the dumps that i found max 2 key are active
buy ETL -> read and if i save has bin from addres 0x0000 til 7FF all on FF
from address 800 to 9FF value is available ok from this addres begin the eeprm address
ok save has bin load in to start error v1.3 the same value for key
37513
if i save has EEF :hmmmm2: i do not understand
Please help me with a Immo dump and ecu dump
after this i have resynk with DAS? if yes it is a problem for me because i do not know German at all
it is possible to have that all ready synchronized
thank you
knok
5th November, 2010, 09:43 AM
i will go mad :motz:this is my firs one but it drive me crazy
first i red immo with digimaster mask 0J66D loaded the eerpm in start error v1.3
Amount off prog key 148 is displayed :hmmmm2: something is not right
al the dumps that i found max 2 key are active
buy ETL -> read and if i save has bin from addres 0x0000 til 7FF all on FF
from address 800 to 9FF value is available ok from this addres begin the eeprm address
ok save has bin load in to start error v1.3 the same value for key
37513
if i save has EEF :hmmmm2: i do not understand
Please help me with a Immo dump and ecu dump
after this i have resynk with DAS? if yes it is a problem for me because i do not know German at all
it is possible to have that all ready synchronized
thank you
your file looks like bad reading .... try to use programmer onto other PC
Artjom
10th November, 2010, 11:10 PM
or i can just give you workinh pair so you can make it work .. if need just tell...
vanos batam
11th November, 2010, 03:10 AM
i will go mad :motz:this is my firs one but it drive me crazy
first i red immo with digimaster mask 0J66D loaded the eerpm in start error v1.3
Amount off prog key 148 is displayed :hmmmm2: something is not right
al the dumps that i found max 2 key are active
buy ETL -> read and if i save has bin from addres 0x0000 til 7FF all on FF
from address 800 to 9FF value is available ok from this addres begin the eeprm address
ok save has bin load in to start error v1.3 the same value for key
37513
if i save has EEF :hmmmm2: i do not understand
Please help me with a Immo dump and ecu dump
after this i have resynk with DAS? if yes it is a problem for me because i do not know German at all
it is possible to have that all ready synchronized
thank you
need ecu dump then post here..
try this dump..
locks85
23rd May, 2011, 08:47 PM
Dear Sir,i have vito with 24c04 and 08az32.
Error start on cluster.
I have software v 1.3 buti used it last week on a sprinter and it didnt work .
Do you have a pair of ecu immo files for the vito please ? Will they work on any engine but with 24c04 and 08az32 ?
Regards
locks85
clauberty
10th June, 2011, 03:41 AM
Hello
Based on diag what should i do
it is possible to unlock just engine ecu with start error software ?
but from whre do i know what to choise Unlock ECU Sprinter SP08C3 v1 or Unlock ECU Sprinter SP08C3 v2
if not possible to do just engine ecu must do immo to :stoned: car have remote door lock will it work after ?
how do i find ecu part nr form EPC for coding
thank you
Powered by vBulletin® Version 4.2.5 Copyright © 2024 vBulletin Solutions Inc. All rights reserved.