MB Sprinter 315CDI DPF Remove EDC16CP31

[sstuning]

Hi
I need quick help with remove particular filter in MB Sprinter 315 CDI.
ECU BOSCH EDC16CP31
BOSCH NR: 0 281 014 344

I work on this car in customer company.
Please help

In attach ori file.

ECU Safe cracked didn't work :/

Thanks in advance

[mercis]

Hi
I need quick help with remove particular filter in MB Sprinter 315 CDI.
ECU BOSCH EDC16CP31
BOSCH NR: 0 281 014 344

I work on this car in customer company.
Please help

In attach ori file.

ECU Safe cracked didn't work :/

Thanks in advance
send results

[Roma]

ECUSAFE not work this car

[sstuning]

Hi
With file from mercis car after repro rides good, but have two errors (read with KTS) - 3151 and 3152.

Today car go to error mode, but don't display MIL light on dash.

[szogun0]

Is this Sprinter from Krosno. :burnout:
Don,t answer. hehe.
I know, it's from Krosno.

[Roma]

That will get rid of the filter it is necessary actual codes of errors?
And then program ECUSAFE?

[soundnavigator]

Hi
I need quick help with remove particular filter in MB Sprinter 315 CDI.
ECU BOSCH EDC16CP31
BOSCH NR: 0 281 014 344

I work on this car in customer company.
Please help

In attach ori file.

ECU Safe cracked didn't work :/

Thanks in advance


Hi, try with this two files and report me.

Best regards.

[sstuning]

mercis - on file from You is ok - I disconnect particular pressure sensor, and all done.
shogun - yes it's from Krosno
soundnavigator - I near time propably i Have identical 315CDI to remove DPF, and I test You file.

Best regards and thanks for help for all
SS Tuning

[szogun0]

So you finally done this sprinter.

[mercis]

mercis - on file from You is ok - I disconnect particular pressure sensor, and all done.
shogun - yes it's from Krosno
soundnavigator - I near time propably i Have identical 315CDI to remove DPF, and I test You file.

Best regards and thanks for help for all
SS Tuning
what tool you use to read ecu?

[szogun0]

I think, that was a BDM.

[sstuning]

Yes, I do this ecu with BDM

[mercis]

you know VAG CAN PRO?
polish interface,verry good product
i want know,with this interface possible read ecu
on Spinter W906 and Crafter
ecu open to BDM hard job(you can make damage)
easy over obd read

[szogun0]

VCP (Vag Can Pro) can't read flash.
It, sometimes read eeprom, but i don't read from ECu until now. Only some Comfort unit and old Instruments from audi.
Can flash ECU's in VAG group, but is very, very unstable (flashing with VAS files .sgo).
I broke ECU in 2.0 TFSI when I update.
I'd never tested on Sprinter, on Crafter works with ECU and Immo. But there are some bugs to correct.
When I tested, it can't do injectors coding.

[mercis]

i bougth now BDM from russian factory,china clone
riskant for me

[mcgustoo]

hi you have all data read from ecu? mpc read, eeprom read and flash?..... you will have program with BDM this flash and click checksum to calculate 100% works... regards!

[2muchtecnology]

Hi, I also removed DPF from 2007 Sprinter EDC16CP31 using ECUsafe and took a full read with EVC BDM 100. After the vehicle had travelled over 350KM 2 fault codes appeared and it goes into limp mode. 1 code relates to a build up of ash inside the particulate filter. ( the filter has been removed) and the second code is for a high pressure pump fault. has anyone had any similar faults?

[fane_81]

Hello. Please remove DFP from Sprinter 318 CDI EDC16CP31 2007

Thanks in advance .

[Kuba_KMS]

try and report

more info I have sent to you on PM.

best regards

Kuba

[macxlulu]

please remove dpf .ecusafe not work

[Roma]

fame_81 The report?

[vwpassat]

Maybe it works and he forgot us.

fame_81 The report?

[monitel_service]

try this file

[monitel_service]

try this files

[benyse]

Hy please remove the DPF from file. ECUsafe not works . Thanks

[mariooo]

Hy please remove the DPF from file. ECUsafe not works . Thanks
hello try this file and after write if it is okay. hello

[benyse]

hello try this file and after write if it is okay. hello

Thanks writing and tested work fine

[benyse]

hello try this file and after write if it is okay. hello
Hello please help me the same problame again . Remove the 2 files the dpf

[autochampion1]

Please remove DPF/ Ecusafe not working (((

[andrze]

Hi I need help with DPF remove from Sprinter 315CDI, EcuSafe doesn't work with it ( no dtc but car in limp mode )
BIG thanks in advance

[LaraVAG]

Try this file, It will be drive ok:) pass in pm

[carsinlet]

Hi i have trued to remove the DPF using ECUsafe on a vw crafter 07 EDC16 but the glow plug light is flashing and the ecu is recording eprom error, i have trued this on two vans and both have same fault. i used a bdm100 the ecusafe program shows the pdf has been removed, i have posted one of the original files from one of the ecus could someone please dpf and egr off, thank you.

[mazilus007]

Hi I need help with DPF remove from Sprinter 311CDI, EcuSafe doesn't work with it
BIG thanks in advance

[niemcow]

Hi

I posted it twice I hope you don't mind.

I have got problem with my friend's W220 3.2 CDI. After remove 3 catalysts there is a problem with EGR. Air mass sensor now has got wrong walue. Air mass is too reach. After few seconds smooth runing engine there is an error of functioning of EGR and every component of this system is checked and works normally also Air Mass Sensor.

In Star Diag Sys there is a function to correct EGR value but it is locked by connection to server.

I can't find such function as EGR remove in EcuSafe. It is EDC15 and there is only EGR function for EDC16. Can somebody help me with this problem.

80204

Thanks in advance.

[delio78]

I have problem with sprinter 315 cdi 2008y
after dpf off, not the possible diagnostic for fault code
car in service mode,i send file tomorow

best regards

[bobolin4o]

What was the error before you remove the DPF?

[delio78]

I read car before writing new file, but no fault code


best regards

[mercis]

I have problem with sprinter 315 cdi 2008y
after dpf off, not the possible diagnostic for fault code
car in service mode,i send file tomorow

best regards
ecusafe disable errorcode

[delio78]

My kts 570 no found ecu engine EDC16CP31.
This file not changed with ecu safe.
I buy file from company.

Best regards

[poki123]

Hi
I need help with DPF remove from MB Sprinter 906

A 646 150 76 91
BOSCH 0 281 014 007

I know that ECUSafe doesn't work with this car.
After patching by ECUSafe there is EGR error and no power at all.

Thanks for advice.

[delio78]

What was the error before you remove the DPF?

throttle valve confused adaptation
this is error code before and after dpf off
throttle valve change with new and error not removed
I have done adaptation, but no change



best regards

[bold36]

please help me to disable DPF on MB Sprinter 315 2007 edc 16

[q-zar]

MB sprinter w906.635 .ecu edc16 mc3-ms9 need help remove dfp.ecu safe 19 not work .ecu safe 20 blocking error code.After ecusafe 19 there is an error to th low pressure turbocharger. At the maximum capacity . files attached

[Roader]

Hello,need remove DPF on sprinter 315cdi,ecusafe not work,no light on but car is in limp mode...

[Mulatre]

You need people who have Swiftec or can do it manualy.

[Youneselm]

try volta sensor mate

[soundnavigator]

Hello,need remove DPF on sprinter 315cdi,ecusafe not work,no light on but car is in limp mode...

You need to do it manually and not unplugged the differential sensor.

Best regards.

[Roader]

ok,if the differential sensor is broken?

[saledjordjevic]

Hi,
please remove the DPF from file. ECUsafe not works.

In attachment is my original file.
Mercedes Sprinter 315CDI
Bosh No. 0 281 014 344

Thanks

[fif]

Anyone know how to remove the DPF Sprinter?

[giorgi2002]

please need hellp to remove dpf
sprinter 906 EDC16CP31-8.20 after ecusafe engine not started

have original file

tanks

[Mulatre]

please need hellp to remove dpf
sprinter 906 EDC16CP31-8.20 after ecusafe engine not started

have original file

tanks

Have you tried to return original back?

[giorgi2002]

Have you tried to return original back?

yes and started

[levisdj]

@ giorgi2002 you should also check if checksum is correct!

[albdiag]

please need hellp to remove dpf
sprinter 906 EDC16CP31-8.20 after ecusafe engine not started

have original file

tanks

ecusafe will not work with this ecu

but to make it start after you write new file than must make checksum. becouse data are changed so need checksum and will start

[albdiag]

w209 edc16cp31

i need dpf off
volta and ecusafe not work

thx

[bemax]

HI PLEASE I NEED YOUR HELP TO REMOVE THE DPF ON SPRINTER W906 ECU BOSCH EDC16CP31 0281015053 THANKS ROLAND BEST REGARDS

[pelot]

Try and report. Pass pm

[didi_du_93000]

Hello Please i need a FULL MPC dump for this ecu:

0281015053
A6461506372


It's very urgent please...

Thanks in advance...

[makura]

Need help as well,posted in the wrong forum.
http://www.digital-kaos.co.uk/forums/f175/sprinter-311cdi-dpf-removal-please-449656/

[alounaha]

Hi!
Please ; I need dpf off Mercedes sprinter 0281015053 BOSCH EDC16CP31
Thanks;