Mercedes E W207 tacho dump

[yannick1800]

Hi everybody,

Can some one give me a dump of the 24C128 chip from the tacho?

I need it urgently...

Please help me.

Thanks

[markony79]

Hi
I have it from 320cdi with 169000km
try this and press THANKS button, I need it

[yannick1800]

Hi
I have it from 320cdi with 169000km
try this and press THANKS button, I need it

are you sure it is from tacho of W207 2009-2010???
because there is no W207 E320...

thanks for your help

[markony79]

No, I think it from w204 c klass, but you must change the VIN NR in dump, then will be the w207

[markony79]

What is with yours, sent me to make a calcul

[yannick1800]

my friend broke my chip before i could get a dump...

do you know location of vin in dump?

[markony79]

try to found with self with winhex
and change it,hack it, not have calcul for this

[yannick1800]

I still need a w207 dump, nobody have one??? Please

[yannick1800]

Please help me :(

[Speedosoft]

Yannick1800,
I just saw your post. I will send you one tomorrow. The file is slightly different than W204 but you need to know that even if you change the VIN to yours it will never display the mileage but only dashes ------. Before someone says that you could roll the KM value close to zero and recode (SCN coding), I wanna go ahead and tell you that it still will not work. These new instrument clusters are an additional drive authorization: FBS. And since you never got to read the file I can't give you that code.
I think the DP3 can take care of that. It's in the following software release:


04.10.2010
Software for programming new MB C-klass (W204), E (W212) and CLK (W207):
- KM - programming kilometers in the odometer by OBDII
- ASSYST - reading service history of the car by OBDII
- SERVICE - servicing, two choices: SERVICE A or SERVICE B by OBDII
- ERASE LAST Ser. - erasing last service entry by OBDII
- ERASE DTC's - erasing history of faults (DTC's) in all car modules by OBDII
- LEARN - used odometer adaptation to the FBS system - by OBDII
- READ EEPROM - reading full memory KI and Assyst (available only to clients who bought data editing, option 802) by OBDII
- WRITE EEPROM - writing full memory KI and Assyst (available only to clients who bought data editing, option 802) by OBDII
Other requirements - not requirent


Speedosoft

[yannick1800]

Can i do it with Xentry???

If DP3 can do it, it must be possible with Xentry?

Thanks for your help!!!

[Speedosoft]

You don't seem to undertsand. You can do it with Xentry if your cluster is brand new. So through the regaular Xentry I don't think it's possible to relearn a used cluster. Maybe you can do it via the developper version. You can always give it a try...

Speedosoft

[Speedosoft]

Here is the file.

[yannick1800]

OK, so it need to be virginized :)

Can you do it? :)

[Speedosoft]

All you need is a 4 byte code located from 0x040 to 0x043 out of a brand new cluster. That way you can "virginize" it and SCN code it from a-z successfully.

[ANIS AKARI]

24c128 W207 CLASIC 143000KM.rar (http://www.digital-kaos.co.uk/forums/attachment.php?attachmentid=40838&stc=1&d=1291068458)