BMW E39 sw13 hw14

[branimirj]

I need to recalibrate this dash,original is 226185
I need 126185.regards

[markony79]

Is this 93s66????

[ipejasinovic]

Yes, It's 93s66...

[branimirj]

Yes 93s66,no way to calculate km?

[markony79]

You must use 2 conector cables blue and white to back side in cluster, and wait to finish, the needles for kilometers will go to 240km , it will be normal, and wait

[branimirj]

What tool you use?

[markony79]

Try this, but I found the original 231xxx not 226xxx
Now I change 126185km

[branimirj]

I try this dump whith licznik.Not working 956xxx :)

[almeida]

us far us i know you could calculate , with diga.
but diga show you a bad reading but you could change and programe.......
but is better if you could programme at a new 93c66 and keep the old 93s66, in case you make mess
:congrats:

[markony79]

Probaj opet u Lizcnik ali izaberi sw12,13
Sa cime si procitao Original Km????

[branimirj]

Bee prog,probano sa licznikom ali ne ide

[markony79]

Car type: BMW E38/E39 High - 93c66 - SW 12, SW 13
The mileage is stored in the next lines:
0040: 25 1C 4C 14 7D 0E 25 1C 4C 14 7D 0E xx xx xx xx
where the next bytes:
25 1C 4C 14 7D 0E - is a mileage

126185km = 2281DC13E09E

To je 126185 km

[branimirj]

Solved,problem is swaped bytes 93s66 only read 16bit organization.Hvala markoni.pozdrav

[carstar24]

Hi guys,

i have the same problem with the same type of car (93s66,SW13). I have readed the EEPROM with bmw scanner 1.36. But licznik can't calculate the original?! (E38/E39 High SW 12,13 93c66). Byte swapping doesn't work.

Whats the problem? Do i have to remove the dash and read with programmer?

best regards,

carstar24

[carstar24]

no idea?

sorry, but i do not understand whats the solution? bmw scanner 1.36 doesn't work?

Do i have to remove the dash and read the 93c66 with 16 bit mode?

[T72]

no idea?

sorry, but i do not understand whats the solution? bmw scanner 1.36 doesn't work?

Do i have to remove the dash and read the 93c66 with 16 bit mode?
yes, please read in 16bit mode and pu dump here. Do not forget its 93s66 so you must conect all 8 legs.
regards

[carstar24]

thx, i will try in a few days ;)

[carstar24]

I found this, it is the connection from the tacho universal:

http://img11.imageshack.us/img11/1048/connectionsw13.jpg

Is this the same connection order as usual in programmers like this?

http://img51.imageshack.us/img51/3356/93s66.jpg

[carstar24]

I'm sorry, I think i have my question wrongly worded.

I have posted before the connection diagram for the tacho universal. But i doesn't have a tacho universal, i have a xprog-m.

My question is...can i use the same connection order of the tacho universal for my xprog-m? :hmmmm2:

[T72]

I'm sorry, I think i have my question wrongly worded.

I have posted before the connection diagram for the tacho universal. But i doesn't have a tacho universal, i have a xprog-m.

My question is...can i use the same connection order of the tacho universal for my xprog-m? :hmmmm2:
connection diagram is good for all ICP programmers! What about xprog-m, I do not think that its good for microwire ICP programing :hello:

[carstar24]

thanks mate for your help...:( why its not good? I have only a xprog-m and a willem 3b.

What do you recommend for this jobs?

I'm not a professional and i have no workshop, i do max. 2 cars in a month.

I'm a truck driver, playing with cars is only my hobby :D

[T72]

thanks mate for your help...:( why its not good? I have only a xprog-m and a willem 3b.

What do you recommend for this jobs?

I'm not a professional and i have no workshop, i do max. 2 cars in a month.

I'm a truck driver, playing with cars is only my hobby :D
willem is shit

in circuit codyprog or carprog

[Nicko_d]

I have the same problem

SW13 with 92S66 in 16bit mode

I changed 40-line...
No right calc for this dash


Please correct damp for 187000.
Original posted there