read/write ISUZU ECU D-MAX

[niwat_spp]

Hi guys,

Everyone I want to read/write ECU ISUZU D-MAX and FORD RANGER TDCI . I have tool. CMD V1255 , CMD FLASH CAN V1251 , and EDC16 flaher all tool clone from chaina.:joyman:
thank a lot

[risalelettronic]

only bdm, read write and chsum tool calculated with delphi adapter

[aidyk]

isuzu d-max can write with galleto i have done them before and they normally have same ecu number.
i had to desolder psop44 to read ori file.
i have ori if you need it :) 3.0 model of course.?

ford tdci i use powergate normally cmd clone wont do it far as im aware.

[niwat_spp]

isuzu d-max can write with galleto i have done them before and they normally have same ecu number.
i had to desolder psop44 to read ori file.
i have ori if you need it :) 3.0 model of course.?

ford tdci i use powergate normally cmd clone wont do it far as im aware.
Oh good.I have galleto v1260 Please send me ori file and software for read/write
thank a lot
:joyman:

[risalelettronic]

isuzu d-max can write with galleto i have done them before and they normally have same ecu number.
i had to desolder psop44 to read ori file.
i have ori if you need it :) 3.0 model of course.?

ford tdci i use powergate normally cmd clone wont do it far as im aware.
3.0 ecus is delphi and is this
and bdm only

[tomtom0785]

not the newer ones - from Year 2007 on they have a transtron ECU with a Hitachi Processor - and it's not possible to do with BDM!!
only the Delphi ECU's

[niwat_spp]

not the newer ones - from Year 2007 on they have a transtron ECU with a Hitachi Processor - and it's not possible to do with BDM!!
only the Delphi ECU's
thank freind i will try with delphi

[niwat_spp]

thank freind i will try with delphi
http://i905.photobucket.com/albums/ac258/niwat1257/link2.jpg
I don't know my BDM ok or not
Please tell me .How to read write with BDM
regards

[autotuning]

check the position of pin 1 on BDM and make your power connections like this,
BTW delphi ecu was only fitted to 2.5 D-max the transtron was on the first 3.0 D-max and later 2.5>2007 (piasinni and V-Spire does these)
early rodeo (not D-Max) 3.0 is bosch edc15 under pass seat desolder psop44 not many files for these just auto and manual
early ford ranger is Mazda piasinni tool later is edc16+ most tools

[weltune]

check the position of pin 1 on BDM and make your power connections like this,
BTW delphi ecu was only fitted to 2.5 D-max the transtron was on the first 3.0 D-max and later 2.5>2007 (piasinni and V-Spire does these)
early rodeo (not D-Max) 3.0 is bosch edc15 under pass seat desolder psop44 not many files for these just auto and manual
early ford ranger is Mazda piasinni tool later is edc16+ most tools

hello
do you know which ic i should read & program if i can loan a car, reset by tech 2 than read it ?attached is some of the photo of the ic i have taken. please advise,
regards
alex

[shay31]

Hi

I need too

I someone know where is ic ??

Thanks
shay

[autotuning]

v-spire and piasini are the only tools i know that work with this ecu with hitachi processor maybe now K-TAG also look on alientech website.

[S.W.A.M.I]

does anyone know if kess or any tool do dmax transtron ecu OBD?

[niwat_spp]

kess v2 can do isuzu transtron via obd and fgtech original

[S.W.A.M.I]

kess v2 china clone can do via obd..

[FritzP]

does anyone know if kess or any tool do dmax transtron ecu OBD?

KessV2 (original tool of course) can read/write the Transtron ecu. I have done a few of these, no problem.

[S.W.A.M.I]

has anyone used k-tag on the delphi ecu to read/write ?

[PierreTheron]

I think on Delphi i used eeprom programmer and BDM

[S.W.A.M.I]

I think on Delphi i used eeprom programmer and BDM

which eeprom programmer and bdm tool did you use?

i only have windows 7

[CLK1201]

KTAG clone can read and write delphi isuzu ,test work 100%

[jtbf]

Hello,
For the isuzu dmax Delphi ecu, did you have to change any of the connectionson the Ktag clone??
Thank you.
jtbf

[jtbf]

Yes,

Ktag V2.10 (clone) works great on Delphi ecu via BDM (Isuzu dmax 2.5 2007).

[carapauxxx]

i know i know its a very old Thread, but anyone know how to read and if its safe to write via obd an Isuzu Rodeo ecu Bosch EDC15M via obd?

[PierreTheron]

ktag should do .
But more info is required m8
1 line seems like no info to me m8.
So i am not going to waste my time to search for you on google with this little info .
All said i waisted a lot off time typing this ...

[Boras]

3.0 ecus is delphi and is this
and bdm only

Hi,
have somenone pinout for read write on bench this ECU? CAN bus?
Regards,
Boras