hilux d4d odometer gone bad.

[jebo]

hi all,

i was working on a hilux d4d dash w/ 93c56.
trying to change odo to 61k (old value was 156k).

the change was successful, it displays 61234k when i turn the car on.

but odometer wont run aymore. it stays at 61234k.

i hope someone out there have any ideas about this.

need help.


thanks !!!

[toniz]

What about speedo needle? Does it work?
check your soldering, or look for a good dump, there are few on the forum.
Or let me know and i'll send you one.

Good luck

[jkschen]

what programmer you using? i had been adjust few hilux , but doesn't matter with this issue. i'm used tacho universal 2008.. maybe u used wrong model.. post ur dump , thanks.

[jebo]

What about speedo needle? Does it work?
check your soldering, or look for a good dump, there are few on the forum.
Or let me know and i'll send you one.

Good luck

toniz,

attached is an image of my dash. pins are numbered where i attached my tacho uni 93c56 wires. i think i dont have probs with soldering. i only opened the back cover of the dash.

yes, all are working well including speedo. its only the odometer thats not moving or counting. i tried to change km again to 65k and it displays 65k when installed to the car. but stays 65k. it doesnt move. trip meter works well (trip a&b)

i think new dump would be helpful.


thanks again guys!

[jebo]

what programmer you using? i had been adjust few hilux , but doesn't matter with this issue. i'm used tacho universal 2008.. maybe u used wrong model.. post ur dump , thanks.


im using same as yours.

attached is my dump.


thanks!

[jkschen]

ur dumps is wrong .Hilux is 95c56si eeprom. did your power on the meter?

[jebo]

ur dumps is wrong .Hilux is 95c56si eeprom. did your power on the meter?

ohhh my.....
yup i powered on the car after re-installing the dash.

is that 95C56???

[jkschen]

jebo, dont worry. very simple . did you save the old dump?
if yes, just write all back. i can help u to adjust the meter. because this is asean car, is different model with europen model. the board and chip supplier is different. but need to dismantle out the needle... i done a lot with this model

[jebo]

jebo, dont worry. very simple . did you save the old dump?
if yes, just write all back. i can help u to adjust the meter. because this is asean car, is different model with europen model. the board and chip supplier is different. but need to dismantle out the needle... i done a lot with this model

jkschhen,

:stoned:no i did'nt save the original dump...:stoned:
hmmm i was trying to dismantle out the needle but did not continue.... i was afraid i might break it. its to tight!
is there a way to safely remove it? do you have a dump for this car?

[n599fbm]

Hi !!

Try with this, It is ok dump !!

Rgds,

C.

[jkschen]

good luck to u jebo. if u have succeful,pls let me know also. but i dont think so.. because begining i also met this problem...thanks for brother n599fbm

[n599fbm]

Hi Guys,

The problem was solved ???


C.

[jebo]

Hi !!

Try with this, It is ok dump !!

Rgds,

C.

thank you very much n599fbm, i'll try this dump as soon as the car gets back. its on a trip now.

i'll let you know asap of the rsult.

jebo

[jebo]

good luck to u jebo. if u have succeful,pls let me know also. but i dont think so.. because begining i also met this problem...thanks for brother n599fbm

thanks too jkschen, i will let you know asap.

[jebo]

Hi Guys,

The problem was solved ???


C.

n599fbm,

i have just finished working on the D4D, and test drive it.
YES IT WORKED!!!
THANK YOU VERY MUCH for the assistance my friends!!!

Jebo...

[jebo]

good luck to u jebo. if u have succeful,pls let me know also. but i dont think so.. because begining i also met this problem...thanks for brother n599fbm



i have just finished working on the D4D, and test drive it.
YES IT WORKED!!!
THANK YOU VERY MUCH for the assistance my friends!!!

Jebo...