Renault Kangoo 1,5Dci Delphi Dcm1.2 HELP

[Anmed]

Hi all!
Please help me to work with Delphi. There is no way to write. At the end of write cycle - a mistake, the content does not change.
Need full ST10F280 and how to write.
The archive photo of the block and the memory contents. If I understand correctly, this is only the calibration table. But even this dump is not written MPPS. Please help.

[ominimicu]

you ll have to use BDM 100

[Anmed]

BDM100? I think you're wrong. How to connect BDM100 in this plate? May be ST10Flasher, but I do not know the connection points...

[Anmed]

Can anybody help me?

[powertdi]

I heard thats processor need boot by two resistors . Can anybody confirm this? TNX

[Anmed]

Yes, so invites MPPS, but it is unknown where on-board pins p0.4 and p0.5.

[ominimicu]

BDM100 has a delphi adapter

[Anmed]

BDM100 has a delphi adapter
Yes, but the ECU has no BDM-port. As far as I know, BDM100 works only with Motorola MPC5xx, is not it?
Problem solved. ST10F280 transferred to the boot mode. MPPS read 512kb, must now collect the dump.
Very desirable like a full dump 512kb for comparison.

[carmelasse]

How to you read this ECU?
Hardware , software, pins?
I need clone this ECU to other.

[alfy]

Please provide more info about the car (Hp, year,...).

[carmelasse]

Renault Modus 1.5 dci year 2006
ECU:
Delphi DCM 1.2 R0410B031B (81117C)
8200399038
8200430215

[alfy]

I have a file from R Kangoo 1.5 DCI 85hp EURO4, year 2007 if someone need. It's a 480kb file read in OBD.

[pablo1971]

i have the same problem with a megane,was there a resolution to this problem.....im stuck and need some help with this

[javiercj]

Yes, but the ECU has no BDM-port. As far as I know, BDM100 works only with Motorola MPC5xx, is not it?
Problem solved. ST10F280 transferred to the boot mode. MPPS read 512kb, must now collect the dump.
Very desirable like a full dump 512kb for comparison.

Hello

I have the same unit delphi.
but I need to connect to read the micro st10f280-b3 (991de) of ecu delphi

the switchboard is a Renault kangoo 1500 dci year 2007

the switchboard is delphi ref: 8200513076 - 8200582518

have tried to load cartography in the flash of the micro for obd and have blocked the ecu.

this ecu stores and save the flash and the eeprom in the micro

I have No car, so I can not do so by OBD and I need to load a new cartography through the micro.

the micro is not motorolla but ST reference: st10f280-b3 and mask 991de

in the micro can read the flash and the eeprom with programmer xprog - m

to make sure the connections and pinear in the right place and not annoy the micro. I've taken the micro data sheet and it does not coincide me.

as you've connected to read this micro and be able to read with the programmer xprog-m and make sure that forms the connections?

I hope your help

many thanks

[ecutuners]

Mpps kills this ecu it cannot make checksum correctly, put ecu in to boot mode and read by mpps generic the full st read, post here with the part read from mpps and I will rebuild the file for you

[javiercj]

Mpps kills this ecu it cannot make checksum correctly, put ecu in to boot mode and read by mpps generic the full st read, post here with the part read from mpps and I will rebuild the file for you


Hello

thank you for answering.

when trying to load a new flash blocks the calculator.

As I put this ecu mode boot mode?' that connection I have to use to put the switchboard at boot-mode.?

and making reading in boot-mode the mpps makes complete reading?

and you reconstructs it for my? and reload with mpps...

To menu I have to use to make reading of mpps generico? can be used mpps6?

you can do reading of this micro with the programmer xprog-m and make reading this? but is connection points them have no clear with the programmer?

may become so, because I don't have the car now?

hope your answer thank you very much

[rabie_m]

bdm??? hhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh hhhhhhhhh

[javiercj]

bdm??? hhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh hhhhhhhhh

i have not port bdm of ecu

[albertros]

Hi,
just a few thoughts that may be wrong but .......

I bought 4 new injectors for a Kangoo 1.5 2002. In the box cam an ecu reprog disc.
When I tried to use the disc on clip the ecu was upto date and the button greyed out.
My piont, will clip do it? you will need the reprog code but a few on here have ad600.

Next DDT2000. I am trying to getmy head round this and played with a kangoo over the week end agian 2002 1.5. I did a search and it found 2 computors one was the ecu, so DDT2000 will prob do it. Not that I can use the program.

I may be confusing mcu with eeprom content butjust my twopenny worth.

Best of luck.

Just spotted this

http://www.digital-kaos.co.uk/forums/f175/dcm1-2-conections-help-208963/

[cavignac]

,
bdm??? hhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhhh hhhhhhhhh
HELLO further explanation please