UPA-USB,... reading MC68HC08AZ32(0J66D)

[Alex_G]

Hello,

Can anyone explain how to read HC08AZ32 (mask 0J66D) with upa, i think i try all, but no success,... lift pins,... all but always low volatge :(

i see someone succed (http://www.digital-kaos.co.uk/forums/f155/x-prog-upa-help-159014/), but for me i never found solution for that hc08az32 with mask 0J66D.

Thanks!!!
Alex_G

[mlulic]

Etl programer

[Alex_G]

So that's it?

No way to make this mask with UPA?

Or maybe Xprog or Xprog-M?

Regards,
Alex_G

[dimitar]

Hello,

Can anyone explain how to read HC08AZ32 (mask 0J66D) with upa, i think i try all, but no success,... lift pins,... all but always low volatge :(

i see someone succed (http://www.digital-kaos.co.uk/forums/f155/x-prog-upa-help-159014/), but for me i never found solution for that hc08az32 with mask 0J66D.

Thanks!!!
Alex_G


select HC08AZ32A in the menu

[Alex_G]

trust me that i try that,.... i don't knwo what else to try,... i always get LOW IRQ (4,64,...) no way to make it work.

Regards,
Alex_G

[Bishop c4]

Hi, Alex
maybe this help you,
http://www.digital-kaos.co.uk/forums/f177/mc68hc908az32-nightmare-read-189107/ (read all thread)

Regards

[dimitar]

trust me that i try that,.... i don't knwo what else to try,... i always get LOW IRQ (4,64,...) no way to make it work.

Regards,
Alex_G


If you get low irq try to lift pin off board and check if there is 9v

[Alex_G]

I did try that also, and i get LOW IRQ alsow :(

Thanks fot advice anyway. I realy don't know what else to try. :(

Regards,
Alex_G

[BATLER]

this chip is usually secured.there is an autobaude rate button and some security bytes to write !!what exactly devise you try to fix?

[Alex_G]

it's airbag module with HC08. No way to read with UPA-USB,... Now i have one on side that can wait and i want to find solution.

Regards,
Alex_G

[Twist]

it's airbag module with HC08. No way to read with UPA-USB,... Now i have one on side that can wait and i want to find solution.

Regards,
Alex_G

i have same problem with air bagmodule VW

but others airbags from (for example) corsa c opel i done it very easy.
look at voltage where is red that leg lift and click on auto baud rate and write this in security bites BE 07 BD 57 BD 57 BD 54

try and send report.

[Twist]

i have same problem with air bagmodule VW

but others airbags from (for example) corsa c opel i done it very easy.
look at voltage where is red that leg lift and click on auto baud rate and write this in security bites BE 07 BD 57 BD 57 BD 54

try and send report.


yes i forgot, and when your volts are green and irq is still bad smoler than 9V then lift rst leg number #3

[johnnts200]

Hi friends!!!.....i have the same problem with a 0J66D mask (opel meriva airbag) and i try a few times "on the board" ...but nothing....
So i desolder the chip and i solder to a pcb only for that with a 8Mhz crystal( it is from a "datasmart" programmer )...and i read/write o.k with upa......(as you see there is a short between pin 55 and 44 )

[johnnts200]

Hi friends!!!.....i have the same problem with a 0J66D mask (opel meriva airbag) and i try a few times "on the board" ...but nothing....
So i desolder the chip and i solder to a pcb only for that with a 8Mhz crystal( it is from a "datasmart" programmer )...and i read/write o.k with upa......(as you see there is a short between pin 55 and 44 )


sorry !!...here is the photo..

Regards!!!

[PierreTheron]

yes i forgot, and when your volts are green and irq is still bad smoler than 9V then lift rst leg number #3


Thanks M8

This info helped me to read airbag ecu for opel corsa with upa..

Many beers to you:beer::beer::beer:

[aaruncee]

Hi friends!!!.....i have the same problem with a 0J66D mask (opel meriva airbag) and i try a few times "on the board" ...but nothing....
So i desolder the chip and i solder to a pcb only for that with a 8Mhz crystal( it is from a "datasmart" programmer )...and i read/write o.k with upa......(as you see there is a short between pin 55 and 44 )


Can you give more info about how to read mc68hc08az32 with upa-usb?

i trying to read opel meriva control module.

thanks

[emanuel2010]

Linft IRQ and RST.
connect pin 61 and pin63 to GND
connect pin 60 to VCC via 1K resistor
i so read corsa c airbag temic.

[crx1616]

i never have problems reading mcu on board dont even lift pin s at all make sure you selet auto baud very important oj66d is not masked if you want i can upload full list of sec byte for this style of mcu aswell !

[brchip]

i never have problems reading mcu on board dont even lift pin s at all make sure you selet auto baud very important oj66d is not masked if you want i can upload full list of sec byte for this style of mcu aswell !

Yes, please do!

[jamerson]

um presente para todos : Bounce:: Bounce:: Bounce:: Bounce:: Bounce:: Bounce:97460

97461

[jamerson]

pesente pra voces amigos estes estao ok, cabo para upa: Bounce: Bounce:

[mariusf11]

Hi .Did you solde only 5 wires ? Do you have original UPA or clone one ? Can you upload a high resolution pic ? Did you power up UPA with external 12 V ? Thanks in advance.

[lati]

You Need 12v for irq, must be 10v

[MNADIR]

With UPA I read MC68HC0?Z32(0J66D)

To unsolder pine 22 and pine 63



To change baud into 14400

[mondis]

Here is my problem that was solved. Mask is not the same but the MCU is. I don't have any problems after this. Here is my post:

http://www.digital-kaos.co.uk/forums/f170/x-prog-mc68hc08az32a-mask-4l52h-251662/

[rocodou]

There is usually no problem to connect and this way I'm reading a very good

[cole_mcs]

Hello,

Can anyone explain how to read HC08AZ32 (mask 0J66D) with upa, i think i try all, but no success,... lift pins,... all but always low volatge :(

i see someone succed (http://www.digital-kaos.co.uk/forums/f155/x-prog-upa-help-159014/), but for me i never found solution for that hc08az32 with mask 0J66D.

Thanks!!!
Alex_G
put auxiliary upa supply 12v and work guaranted

[cleevesy]

Read Chrysler Skim , connected as upa manual , connected power supply , read perfect happy days!!!

[scary]

try use upa whit 12v and 2 amp just dont forget swhic jump should work

[agc]

Hi I have the same problem UPA Motorola 0j66d, reset error.
Everything connected fine.
Can know what the problem is?

[mercis]

put first aut.baud rata

[thiburco]

sorry !!...here is the photo..

Regards!!!

where I buy only these adapters?

Thanks!

[sasaran]

pls start error red all memory upa