citroen c4 picasso 2008 years

[javilette]

hi i have a problem whith this car , i have 116876km in dash and bsi i try to change the miliage but when i put the news dump the car show 00000km all the car works ok but have 0km i try to put bsi reset whith tachosoft 20.x c4 2007 years and the dash is not the same of tachosoft but nyo4 have this version and i put 52xxx. i try to put the 52xxx km in the bsi but it show to me 0km too. somebody can i help me. i put the original dump and the bsi reset and dash whitc 52000.

regars

[Ramzai]

Try this dump BSI. In dash 52123km.

[marcio1758]

hi i have a problem whith this car , i have 116876km in dash and bsi i try to change the miliage but when i put the news dump the car show 00000km all the car works ok but have 0km i try to put bsi reset whith tachosoft 20.x c4 2007 years and the dash is not the same of tachosoft but nyo4 have this version and i put 52xxx. i try to put the 52xxx km in the bsi but it show to me 0km too. somebody can i help me. i put the original dump and the bsi reset and dash whitc 52000.

regars

dear brother of DK, when you install and appear 0 km, leave about 10 minutes with the switch on for the new km may appear, sometimes it takes a while for the panel to communicate well with bsi!
:ciao:

[tachonow]

If the correction algorithm is good km will be shown instantly.
This bsi has crypted checksum on km and doesent work with zero.

[drpeter]

If the correction algorithm is good km will be shown instantly.
This bsi has crypted checksum on km and doesent work with zero.

only if you put 2103 behind the 000000 :-)

[Eight]

just a good calculation solves the problem.

[javilette]

dont work this dump. a peculiar thing, in the menu of change of single language appears French only, you cannot change language.the car is imported of France.

[markony79]

hi i have a problem whith this car , i have 116876km in dash and bsi i try to change the miliage but when i put the news dump the car show 00000km all the car works ok but have 0km i try to put bsi reset whith tachosoft 20.x c4 2007 years and the dash is not the same of tachosoft but nyo4 have this version and i put 52xxx. i try to put the 52xxx km in the bsi but it show to me 0km too. somebody can i help me. i put the original dump and the bsi reset and dash whitc 52000.

regars

Here is dash dump
in Bsi put zero,
must work,
this is good calcul I chech again
your is not OK, becouse of that is come km from Bsi--000000km

put this and you will see, you no need now bsi change

[javilette]

i will try tomorow but if you see the hex data where you see
40
40
in the original you see
79
78
i think that if it is good should have other value.

[markony79]

i will try tomorow but if you see the hex data where you see
40
40
in the original you see
79
78
i think that if it is good should have other value.

Bsi 0km version 4
put this and must work

[javilette]

this file dont have any write in line 00007f0 to 0003ff0

[markony79]

this file dont have any write in line 00007f0 to 0003ff0

I use calculator from DP3, I not trust Tachosoft
I found original value and make on 0km,
must work

[javilette]

sometimes the dp3 dont have the version, you can see the original data put the new and dont work in car , i had this problem whith citroen c2 ,c4 peugeot 307 .i have dp3 too but i dont have here .

[markony79]

sometimes the dp3 dont have the version, you can see the original data put the new and dont work in car , i had this problem whith citroen c2 ,c4 peugeot 307 .i have dp3 too but i dont have here .

Ok, but did you try this?
And Tachosoft 21.5 work only on cars to 2008