PDA

View Full Version : HELP with BDM 100


levisdj
25th February, 2011, 06:00 PM
I made a mess, I accidently erased the BDM memory with this program : MProg 3.5 . I'm asking whoever has another program to reflash this tool, and the entire BDM chip content, I would be more then gratefull.I've also uploaded the MProg 3.5
levisdj
26th February, 2011, 12:43 PM
Noone?? The chip inside the BDM says : MC68HC11E1CFN3 . Please help!
mexanico1971
26th February, 2011, 02:38 PM
maybe you have to use xprog ! got to seach !
levisdj
26th February, 2011, 05:32 PM
Yo're saying that I need the Xprog device, or only the software ?
levisdj
1st March, 2011, 10:07 AM
Does anyone atleast know if the MC68 can be reprogrammed trough the BDM interface? or do I need the XprogM ?
exe123
1st March, 2011, 10:18 AM
With Mprog you can erase the 93C46 eeprom only. the 68hc is still ok. you just need to get the ept-file from a working bdm and rewrite it with mprog.

for programming the 68hc you will need xprog, upa or some other programmer.
Novik_UA
1st March, 2011, 07:40 PM
Try mine eeprom from BDM100 CMD1255 clone .
levisdj
2nd March, 2011, 08:47 AM
Ok, so I managed to write the ept file... but DimSport still says: no device found.In the list of the USB Devices it's installed as : "Map3D OBD II Interface" . I've uploaded three pics... One has the FT232BL that says : BLANK DEVICE ??
So, what next ?
levisdj
2nd March, 2011, 08:49 AM
Here : the three atachements
alfy
2nd March, 2011, 08:49 AM
You need the FT232 file, to reupload with mprog...
I don't have it.
levisdj
2nd March, 2011, 04:20 PM
Here's the FT Programmer, if someone could make a copy of his FT232BL file and upload it here please....Open the software, connect the device, press : "Scan and Parse" then save the file.The file must be in *.xml format in order for me to be able to re-write the FT....
levisdj
4th March, 2011, 01:18 PM
No xml file ? it only takes two minutes guys ...
Samaelson
4th March, 2011, 01:34 PM
Hi,

you haven't erased the Motorola chip but the eeprom of the FTDI chip in your device! You need the reprogramm either using FT_Programmer oder MProg, doesn't matter!

Search the forum for BDM1255! The file for the eeprom ist still there!

Best regards!

Sam
levisdj
7th March, 2011, 03:32 PM
Yes... but I need the XML file to reprogram the FTDI... because it says : BLANK DEVICE
levisdj
8th March, 2011, 03:40 PM
So, I've done all above... this still doesn't work.I reprogrammed it with Mprog... no use.What next ?
levisdj
10th March, 2011, 04:29 PM
Doesn't anyone have an answer ???
levisdj
22nd March, 2011, 11:04 AM
Still noone ? I'm sure I'm not the first one with this experience... could someone point the mistake ? Thanks guys..
levisdj
22nd April, 2011, 11:12 AM
I guess noone had experience with this problem ?
redful
5th August, 2012, 04:58 PM
HI ALL

THIS IS A 100P100 WORK FILE PROGRAMME IT

WITH A EEPROM PROGRAMMER
tagar
13th August, 2012, 04:22 PM
I'm checking my chinese BDM100 which is no longer working. I have doubt on the MC74HC14AD chip. I plug the BDM to the USB port of laptop. pins 5(DSCK) and 7(DSDI) when measured to ground (pin6) with DMM is showing 5V (flat cable not connected to ECU). Very much appreciated if anyone here can verify this is correct or wrong.
AGS
13th August, 2012, 05:04 PM
I'm checking my chinese BDM100 which is no longer working. I have doubt on the MC74HC14AD chip. I plug the BDM to the USB port of laptop. pins 5(DSCK) and 7(DSDI) when measured to ground (pin6) with DMM is showing 5V (flat cable not connected to ECU). Very much appreciated if anyone here can verify this is correct or wrong.
I have sum problem with pcb,check solder near motorola socket,and if motorola dead,no +5v,try unplug motorola from socket and check voltages