Citroen Saxo M7.4 immo

[i_shot_the_sheriff]

Hey m8tes,

I just received an ecu from a Citroen Saxo with Bosch ecu (0261206246)!
I want to get the immo off but i can't recognice the eprom...
i mean... i've found 8pin eprom in the ecu (95080) but all the programs for immo i got don't have that 95080.. they suggest the 95160!!

Is the eprom the 95080 chip? And if yeah... can you get the immo off (cause i can't :P)?


Thanks in advance

[i_shot_the_sheriff]

Here is the file i've read from the 95080!

Also.. i've noticed there is an 29F400BB on the ecu... is that the flash? Do i need to do something to the flash?

[BATLER]

otocheck use 95080ep for this ecu m8

[i_shot_the_sheriff]

Actually the immo tool worked! But i've tried it on the Peugeot 106!! I think it's the same!

[i_shot_the_sheriff]

Another Saxo with the same number came to my store today!
I've tried the same solution (with Ottocheck) but it won't start! (the immo light is beeping)

What to do? :O

[i_shot_the_sheriff]

Also i've tried the old immo off solution (from the old Saxo) and it wont start again!

[gadroulll]

i think that you have 29f400 and 95080 immo off
bosch 7.4.4 has 95160 memory

[i_shot_the_sheriff]

Yes, on the ecu there is a 95080 and a AM29F400BB!!
Should i read both? What should i do?

[busaman]

try this it works are you sure it m7.4.4 and not ma7 or me7

[i_shot_the_sheriff]

I've tried the file you gave me!
The immobilizer light is still blinking and the car won't start!

Yes i'm sure it's m7.4.4 (it's written on the ecu too)!

You know, i've noticed that the check engine light was off! With the file you gave me the check engine light was on while i open the ignition!

[i_shot_the_sheriff]

Do i have to read the 29F400 too?

[busaman]

did you cut immo wires f3 and f4 on the ecu.

[i_shot_the_sheriff]

Mate i will try that but.......
But...
I've tried 3 ecus, and all of them didn't work! The mysterious thing is that... Check Engine Light won't light on the 3 ecus! :O Did i burn them?

There is something really wrong with that car!
I take a used ecu (locked) and try it on the car! Check Engine light is ok but the immobilizer is ON! I read the 95080 and do the immo off you suggested, do the immo off from Ottockeck.... i solder the 95080.... try it on car.. and... The Check Engine light is OFF and the IMMO light is ON and the car won't start! i say ok... wrong file!.. I reset the 95080 to the previous file and the CHECK ENGINE LIGHT is OFF!!!!!!!!!!!!!!!!!!!!!!! WHAT IS GOING ON?

[maglaras]

hello
greece here
take out the immo box and the car start ok
if you need somthing to help you telm me to give you me nuber ok

[ggpanos]

Is you tel no +3025******76 ? I can tell you your IP too... :D

[i_shot_the_sheriff]

Ggpanos that was pretty easy ;)
hmmm, my IP too!
You want a difficult one? Fix saxo!! ;)

[JIMMYQ]

hi ive got same ecu just a little confuses on which pins to cut as there are f3 on either side ? and f4

[leandroks]

hi ive got same ecu just a little confuses on which pins to cut as there are f3 on either side ? and f4
If peugeot or citroen no ned to cut pins;;;; Cheers

[JIMMYQ]

mines a citroen saxo? and is it just the eeprom i need to do ?the ecu i have is a M7 4.4

[jairpg21]

Try this files, worked for me once

[leandroks]

both eeprom and flash as well...
95xxx and 29fxxx

[gadroulll]

use flash of ecu m744 that ends in 246 .peugeut 106.

use now files from otocheck or other tools and it will work.

only flash from ecu peugeut is open for memory 95080