IMMO opel simtec 56.1

[CHARLE]

Hello
I need immo of 93c56 for opel calibra simtec 56.1.
I read the eeprom but why I can do now ?
Thanks

[tomaszcz]

Hello
I need immo of 93c56 for opel calibra simtec 56.1.
I read the eeprom but why I can do now ?
Thanks

Read eprom 93c56.

[CHARLE]

Hello Tomaszcz

I read the EEPROM 93c56 with ponyprog2000 and I got this file:

What data should I change for remove immo ?
Thanks

[tomaszcz]

Hello Tomaszcz

I read the EEPROM 93c56 with ponyprog2000 and I got this file:

What data should I change for remove immo ?
Thanks

Try this end send report.

[CHARLE]

Thanks tomaszcz for your quick reply !!!
I will test this W.E. and I reply you.
Best regards

[CHARLE]

Hello Tomaszcz

I tested the EEPROM with the new file.
I got a serie of flash light engine, then a pause, then a long flash, then a pause, a long flash, a pause and then the light engine flashes continuously. Is this normal?
I tested the unit on a workbench. See photos
Should I strap the immobilizer 5WK4596 and make a jumper between pin 6 and pin 7 ?
Thanks you very much
Eric

[tomaszcz]

Hello Tomaszcz

I tested the EEPROM with the new file.
I got a serie of flash light engine, then a pause, then a long flash, then a pause, a long flash, a pause and then the light engine flashes continuously. Is this normal?
I tested the unit on a workbench. See photos
Should I strap the immobilizer 5WK4596 and make a jumper between pin 6 and pin 7 ?
Thanks you very much
Eric

Try this file.
Engine start but light check on this file.
Remove immo box.

[tomaszcz]

Hello Tomaszcz

I tested the EEPROM with the new file.
I got a serie of flash light engine, then a pause, then a long flash, then a pause, a long flash, a pause and then the light engine flashes continuously. Is this normal?
I tested the unit on a workbench. See photos
Should I strap the immobilizer 5WK4596 and make a jumper between pin 6 and pin 7 ?
Thanks you very much
Eric

I have a dump immo off with eprom 27c256

[CHARLE]

Hy ! You are super fast in your answers !
It is a pleasure to conver with you.
I will test tonight the file for the 93c56, but for
the 27c256 memmory I must find a programmer
in my office.
I'll let you know.
Thanks very very much !
Eric

[CHARLE]

Hello Tomaszcz

I don't find a programmer for 27C256. I buy it on internet
a Willem PCB50B. I wait after the package..... I think wait about two weeks the programmer comes from china !
Good W.E.
Best regards

[CHARLE]

Hello Tomaszcz


I finally got the programmer Willem PCB5.0 this W.E..
It works and I have programmed the EPROM 27C256 with the file that you sent to me. His name: OPEL_OMEGA_SIMTEC_off.rar
The ecu operates fine on the table!! I can also do the test of "paper clip"to read the faults codes stored in the ecu. For the 93C56 eeprom I can put the original th ECU works also !!!
I must test the ECU on the car. I think it's good because the engine light stays on orange and not blinking when I test on the workbench.
I leave the immobox and the ECU run with the new Eprom 27256.
A big thank you for your kindness and your skill!

[tomaszcz]

I share file without pass

[sogaro]

I could not write on this eprom with my tool, kept failing or is it an OTP? It has no glass on it though?

[Shmortz]

it must be OTP, what type is it?

[sogaro]

Sure its OTP, AM27C256 and i dont have a replacement neither can i get one easily.

[chong5195]

Pls share Opel 56 immo off file password pls