Instructions for OP-Com update

[e.t.]

Hi,
can someone make a small guide that the OP-COM (clone) can upgrade to v1.44 firmware.
If possible with pictures.
Does that make the OP-COM Advance?

Thanks

[Ashraf6119]

Hi

The normal Op-Com and Op-Com Advance are two different things so, there is NO way by updating up your clone Op-Com to become Op-Com Advance.............

And if you are thinking of updating your Clone op-Com than you can update it from this site here which is tested and its working with clone once................

http://opcomforum.yolasite.com/software.php

Hope this helps........


Ash

[mishu_b]

...
just run the last Op-Com software and your tool will automatically update to fw 1.44.

atb

[e.t.]

What is the last software for OP-COM Clone?

[mishu_b]

...
according to the rules (new rules) you will not find here the last software for clones.

atb

[e.t.]

And whats the number?

[mishu_b]

OP-COM CHINA 08-2010 - one of the last Op-Com software cracked - usable with clones.

atb

[Barm76]

Update can be easy, if you will use this loader with FW1.43&1.44 :)

[cristian2011]

Hello! If I install latest version of op com, I will automatically updates the interface to version 1.44? Thanks to all

[RMCtech]

Yes, if you use latest soft it will update your clone to 1.44 but many functions will not work, and you will have an almost useless interface.

My advice is: Forget the v1.44 firmware, it don't work fine on clones.

The latest usable soft in clones is firmware 1.39 of China OP-Com 08-2010

[mishu_b]

...
correct

you do not need to update the interface because the last working software with clone tool is op-com 08-2010 which required fw.1.39

atb

[mattydr67]

Mates yes that's right like Mishu_b said that you don't need to upgrade to 1.44 just because Op-Com china clone 08/2010 need fw 1.39.
But I cannot tell you that Op-COm not works well with fw 1.44
There's not any difference between 1.39 and 1.44 if use all cracked version of Op-Com.
Good luck

[phara0n]

i have original. but cant find any serious website that speak about even official updates ive too much problems getting them who czn help?

[meteor80]

Confirm.
Version 1.44 is a piece of sh*t.
It doesn't work with same modules like Airbag or dash.
1.39 works fine.

[mattydr67]

May you explain or named the controlers that you couldn't connect?
I mean the models on which cars?
Becasue that's something new for me what you said. I have an upgraded 1.44 tool and I haven't no problems to connect on any moduls.
So I'm intrest to check by my self.
Thanks
Good luck

[meteor80]

I had Opel meriva 2006 to log in radio, but I couldn't read secutiry code from dash (older fv OK) and I couldn't reconfigure airbag module in Opel astra H 2008.

[meteor80]

In meriva there was possibility to connect with newest firmware of OP-COM but not possibility to read eeprom.

[mattydr67]

I see I will try by my self too
And you tell me that with 1.39 you could and with 1.44 you coudn't
Good luck

[meteor80]

Yes 1.39 :D fine 1.44 bad :hmmmm2:

[spychu14]

I've heard that op-com can repair airbag sensor.
Is it true ?? I've to fix it in astra H 2010.

[mattydr67]

Do you mean Crash Data?
Good luck

[meteor80]

Only some of modules You can do using opcom.

more You can find here:
http://opcomforum.yolasite.com


Don't forget to press magic button :D

[raymos1501]

There is no way to return the 1.44 firmware to 1.39? with opcomfut29b not working.
regards.

[lupu_sandu]

Only with programmer