VAG-COM procedures

[marius_uet]

Taillights:

[Select]
[09 - Centr. Elect.]
[07 - Coding]
[Long Coding Helper]

Byte 9: Uncheck all the boxes or change the DEC box in the figure 0 (zero)

[Transfer Coding!]
[Do It!]

[marius_uet]

Activate Leaving Home & Coming Home


NOTE: It is not necessary to have your car lights or light sensor for automatic turn on these features!


[Select]
[09 - Cent. Elect.]
[07 - Coding]
[Long Coding Helper]

Byte 0:
- Check Bit - 5 (Light Driving Assistance - Leaving Home Active)
- Check Bit - 7 (Coming Home-active)

[Transfer Coding!]
[Do It!]

[marius_uet]

CD Radio screen display speed.


If set to show speed, we will see the title song or radio station.


[Select]
[56 - Radio]
[10 - Adaptation]

Channel 02: 0 = off / 1 = activate (display speed in km / h on the radio display)

[Test]
[Save]
[Done, Go Back]

[marius_uet]

Closing project when you flash or beam

[Select]
[09 - Centr. Elect.]
[07 - Coding]
[Long Coding Helper]

Byte 17: Check Bit - 5 (Front Fog Lights deactivated with High Beam)

[Transfer Coding!]
[Do It!]

[marius_uet]

Change time for Coming Home & Leaving Home



[Select]
[09 - Cent. Elect.]
[10 - Adaptation]

Channel 01: number of seconds you want to be actively coming home - from 0 to 120
Channel 02: number of seconds you want to be actively leaving home - from 0 to 120

[Test]
[Save]
[Done, Go Back]

[marius_uet]

Regeneration particulate filter (DPF).


NOTE: This procedure is performed only if the procedure described in the user manual of the car does not work!

Tested on 140 hp 2.0 TDI engine.

Put the ignition, engine running water over 50 degrees (see Temperature Measuring Blocks channel 002, field no. 4)

DPF values to follow in Measuring Blocks channel 075, box no. 3. If the load value is above specs (from box No. 2), the filter must be replaced, otherwise it can crack during regeneration.

Consumers attach electrical and mechanical engine can be started (incalizre seats, climate, lighting, etc etc)

EGT's (exhaust gas turbine AHEAD) to be above 700 ? C before starting the test.


[Select]
[01 - Engine]
[Coding-II - 11]

Enable regeneration by introducing code 21295.

[Do It!]
[MEAS. Blocks - 08]

Groups-select channels 070 and 075.

[Go!]

Meanings:
Box No. 070 Canal. 1: Regeneration status (active Regeneration xxxxxxx1 = Normal, Forced Regeneration xxxxxx1x = active)
Box No. 070 Canal. 3: Regeneration Counter / Timer Duration
Box No. 075 Canal. 1: EGT before turbo
Box No. 075 Canal. 2: EGT before Particle Filter
075 Canal box 3: Charge Particle Filter - Particle Filter Load
075 Canal box 4: EGT by Particle Filter

Turn and follow the above mentioned values.

The car runs 30-60 km / h - at 1500-2500 rpm, duration approx. 15 to 20 minutes. Particle Filter Load driving until it becomes closer to 0% (but in the mentioned period).

If the values do not decrease when driving conditions are not appropriate with the data here or your engine has mechanical or electronic problem (valves, cam, overhead cam, injectors, compression - or flow meter, water sensors, actuators turbo / EGR)

[marius_uet]

Cancellation diagnosis error "bulb burned signaling



[Select]
[09 - Centr. Elect.]
[07 - Coding]
[Long Coding Helper]

Byte 18:
- uncheck bit 5 (Cold Diagnosis Turn Signals active)
- uncheck bit 7 (Cold Side Turn Signals active Diagnosis)

[Transfer Coding!]
[Do It!]

[marius_uet]

Change screen display language


[Select]
[17 - Instruments]
[10 - Adaptation]

Channel 04:

00001 - German
00 002 - English
00003 - French
00 004 - Italian
00 005 - Spanish
00 006 - Portuguese
00,007 - no text
00,008 - Czech

[Test]
[Save]
[Done, Go Back]

[marius_uet]

Automatic shutdown after the car speed 15km / h


[Select]
[46 - Cent. Conv.]
[10 - Adaptation]

Channel 03: Auto Lock after 15km / h (1 = ON / 2 = Deactivate)

[Test]
[Save]
[Done, Go Back]

Automatic opening of the car after removing the key from the ignition


[Select]
[46 - Cent. Conv.]
[10 - Adaptation]

Channel 04: Auto Unlock after removing the key (1 = ON / 2 = Deactivate)

[Test]
[Save]
[Done, Go Back]

Optionally you can set when closing / opening the car to catch fire damage or to hear a short clacson
For these changes and:


Optional channels - blinkers flash or sound horn said:

Channel 05 Unlock, horn sounds (1 = ON / 2 = Deactivate)
Channel 06: Lock, horn sounds (1 = ON / 2 = Deactivate)
Channel 07 Unlock, turn signals flash (1 = ON / 2 = Deactivate)
Channel 08 Unlock, turn signals flash (1 = ON / 2 = Deactivate)

[marius_uet]

SEAT BELT CHIME:

Control Module Coding
Select 17 (Instrument Cluster)
Coding -> Function 07
00??x0x: Extra-Options

+01 - Brake Pad Warning active
+02 - Seatbelt Warning active
+04 - Washer Fluid Warning active
+16 - Sedan (Jetta)

So if you wanted everything active....
0023x0x where x is the value of the original coding, let's say it was set there from the factory.

To remove seat belt warning, just subtract the 02.... so it would now be:
0021x0x
My stock coding:
0023203
With no seat belt chime:
0021203

[marius_uet]

Enable automatic closing of windows by holding down the button just 2 seconds

[Select]
[46 - Central Conv]
[07 - Coding]
[Long Coding Helper]

Byte 6:
- Check Bit 6 (Comfort function autom. closing)

[Transfer Coding!]
[Do It!]

[marius_uet]

Enable DRL (s) per project to 50% in intensity


[Select]
[09 - Central Electric]
[07 - Coding]
[Long Coding Helper]

Byte 00: - Check Bit 4 (Daytime Running Lights (North America))
Byte 17: - Check Bit 4 (via Daylight Running Light Front Fog Lights)
Byte 20:
- DEC changed the value in the box (in percentage) in 50

[Transfer Coding!]
[Do It!]

[marius_uet]

Opening pistons to replace rear brake pads


[Select]
[53 - Parking Brake]
[04 - Basig Settings]
Group: 006
[Start!]
Activating Basic Settings
[CON / DEC / Next]
(This will open the caliper.)
[Done, Go Back!]
Now you can replace the brake pads

After closing piston rear brake pad replacement


[Select]
[53 - Parking Brake]
[04 - Basig Settings]
Group: 007
[Start!]
Activating Basic Settings
[CON / DEC / Next]
(This will close the caliper.)
[Done, Go Back!]

Note: the 010 Group's "basic settings" has the character test, the first phase opens 1x caliper, then raise 3x.

[marius_uet]

The "cornering" on projectors!

NOTE: This function works only activated car produced after July 2007!


[Select]
[09 - Cent. Elect.]
[10 - Coding]
[Long Coding Helper]

Byte 23:
- check Bit2 (Internal Control Tower Light Algorithm s)
- selection to the bit 3-4: 08 Fog Lights Tower Lights Zoom

[Transfer Coding!]
[Do It!]

[marius_uet]

how to change the alarm sound.


[Select]
[46 - Cent. Conv.]
[10 - Adaptation]

Channel 10: Alarm Horn

Here you choose between 0,1,2,3 bits that you like.

[Save]
[Done, Go Back]
I played myself in the summer than the alarm and they consider two types of tones are grouped in bits 0 and 2 (more or less resembles the alarm) and bits 1 and 3 (cheep) and if I remember correctly, the two groups of sounds on bits 1 and 3 is heard louder.

[cosmind]

good working, dont stop

[labusas]

how about key learning for jetta 06,CAN chip?

[neriuks007]

i have audi a8 2001year,how to do off tire presure sensors off? thanks.

[neriuks007]

how to coding without tire sensors?

[fakirgsm]

good working, dont stop

[flint77]

Specific Modules:
01-Engine: -- KWP-2000
VAG-COM works well with all engines available in the U.S. and most engines that users have tested in overseas markets.
02-Auto Trans: -- KWP-2000
VAG-COM works fine.

03-ABS Brakes: -- KWP-2000
VAG-COM works fine.

05-Acc/Start Authorization: -- KWP-2000
VAG-COM works fine.

06-Seat Memory - Pass Side: -- KWP-2000 (If equipped)
VAG-COM works fine.

08-HVAC: -- KWP-2000
VAG-COM works fine.

09-Central Electronics: -- KWP-2000
VAG-COM works fine.
To put the DRL into the MFI menu as an option:
[Select]
[09-Cent. Elect.]
[Recode - 07]
Write down the existing coding for future reference.
Enter the new code from below
[Do It!]
Look at the existing 7-digit Soft. Coding. If you do not have DRL in the MFI menu, your coding should be an odd number. To put the DRL into the MFI menu as an option, subtract 1 from the coding.
Example: So, if you do not DRL in the MFI menu and your existing coding is 0105695, subtract one to make it 0105694 To put the DRL into the MFI menu as an option.
State
Hex Bit
Decimal
Function

ON
0
1
DRL Control Blocked in MFI

ON
1
2
Halogen High Beams
(Xenon Low Beams off when High Beams on)

ON
2
4
Interior Lighting Enabled

ON
3
8
Rain & Light Sensors Enabled

ON
4
16
Coming Home Lights Enabled

OFF
5
32
Rear Fog Enabled

ON
6
64
Front Fogs Enabled

ON
7
128
Xenon Lighting Enabled

OFF
8
256
Marker Lights Enabled

OFF
9
512
Unknown Function

ON
10
1024
Headlight Washers Enabled

ON
11
2048
Electric Fuel Pump Relay Block
(Gasoline Engines Only)

ON
12
4096
Wake-up function Enabled

OFF
13
8192
Second Battery Enabled

OFF
14
16384
Auxilliary Battery Enabled

ON
15
32768
Low Seatheating Enabled
(Memory Seats Only)

ON
16
65536
Electronic Load Management Enabled

OFF
17
131072
Rear Fog Disabled when in
Off-Road Suspension Setting

On our 2004 Touareg V8, we had the following options enabled from the factory:
65536 + 32768 + 4096 + 2048 + 1024 + 128 + 64 + 16 + 8 + 4 + 2 + 1 = 0105695
To add or remove a function, add or subtract the Decimal value for that option.
11-Engine 2: -- KWP-2000
VAG-COM works fine. This is only applicable to V10 TDI engines.
15-Airbags: -- KWP-2000
VAG-COM works fine.
Important Note: Please do NOT run Output Tests (function 03) on your Airbag Controller!
No, it won't deploy your airbags. But it MAY render the vehicle undrivable. Running Output Tests is supposed to make the airbag controller generate a simulated crash signal to the rest of the systems in the vehicle so that unlocks itself and shuts various things OFF. Unfortunately, one of the things it shuts off in the Touareg is the power supply to the Engine Control Module. Two things are needed (confirmed by a dealer tech who was brave enough to run Output Tests on an Airbag Module):
1. Clear "Crash Data" code from the DTC Screen in 25 - Immobilizer.

2. Reset the yellow Circuit breaker under driver's seat. The circuit breaker should be yellow and should be visible/accessible if you remove the carpeted "step" trim panel at the front of the seat (an operation requiring some dexterity, but no tools).
Beginning with Beta 310.0, VAG-COM will pop up a warning if you try to run Output Tests on the Airbag Controller.
16-Steering Wheel: -- KWP-2000
VAG-COM works fine.

17-Instruments: -- KWP-2000
VAG-COM works fine.
Recoding for chime and warning lamp preferences:
[Select]
[17-Instruments]
[Recode - 07]
Write down the existing 7-digit Soft. Coding for future reference.
Enter the new code from below
[Do It!]
Look at the existing 7-digit Soft. Coding. Look at the fourth digit in the coding. Add the values for the options together to get the correct coding.
0 - No available equipment
+1 - Brakepad wear sensor warning active
+2 - Seatbelt warning active
+4 - Washer fluid level warning active.
Look at the fifth digit in the coding (Market version):
1 - "Europe" (No Navigation system acceptance screen, also see 56-Radio for other changes)
2 - "USA" 12 hour clock (Navigation system acceptance screen)
3 - "Canada"
4 - "UK"
Example: If you have all of the above warnings active and your car is set to USA (and your factory Soft. Coding is 0007231), if you would like to remove the seatbelt warning, subtract 2 from the fourth digit to make the coding 0005231. If you would like to keep the seatbelt warning, but remove the Navigation acceptance screen, then change the fifth digit from 2 to 1 to make the coding 0007131. If you'd like to remove both the seatbelt warning and the Navigation acceptance screen subtract 2 from the fourth digit and change the fifth digit from 2 to 1 to make the coding 0005131.
19-CAN Gateway: -- KWP-2000
VAG-COM works fine.

1C-Level Sensing: -- KWP-2000 (If equipped)
VAG-COM works fine.

22-All Wheel Drive: -- KWP-2000
VAG-COM works fine.
25-Immobilizer: -- KWP-2000
VAG-COM works fine.
29-Left Light: -- KWP-2000
VAG-COM works fine.

34-Level Control: -- KWP-2000 (If equipped)
VAG-COM works fine.
See our page on Touareg Suspension Level Control Calibration

36-Driver's Seat: -- KWP-2000 (If equipped)
VAG-COM works fine.

37-Navigation: -- KWP-2000 (If equipped)
VAG-COM works fine.

39-Right Light: -- KWP-2000 (If equipped)
VAG-COM works fine.

46-Central Convenience
VAG-COM works fine.

47-Sound System
VAG-COM works fine.

56-Radio: -- KWP-2000
VAG-COM works fine.
Important Note: If you have recoded 17-Instruments from USA to Europe, this changes the way the Radio operates. Note that Europe uses different specs for their radio compared to North America.
FM:
FM frequencies in Europe are spaced .1MHz apart, compared to .2MHz in North America. This causes no problems in using a Nav Plus in North America, it just means you can tune into some frequencies (such as 92.2) which don't exist here. Since it can tune into all the North American FM frequencies that do exist, it works fine.

AM:
AM frequencies in Europe are spaced 9kHz apart, compared to 10kHz in North America. Europe also does not have AM Stereo, so the Nav Plus does not support it. This DOES cause a problem. It means you can only get "close" to some stations when trying to tune them in. It may sound a bit like an AM tuner when you turn the knob just off station, but if you are an AM audiophile, this may be an issue for you. If there is a particular AM station you like to listen to, you can calculate if the Nav Plus will get close in frequency. Simply start at 531kHz, then add 9 kHz until you get close. For example, if you have a favorite station at 660Khz, the closest you can get is 657kHz. The most a station will be out by is 4kHz.
65-Tire Pressure Monitor: -- KWP-2000 (If equipped)
VAG-COM works fine.

68-Wipers
VAG-COM works fine.

6E-Control Head Roof: -- KWP-2000 (If equipped)
VAG-COM works fine.
To turn console compass on all the time:
[Select]
[6E-Ctrl Head Roof]
[Adaptation - 10]
Channel 01
[Read]
Write down the existing value and enter "00" as a new value.
[Test]
[Save]
69-Trailer Control: -- KWP-2000 (If equipped)
Not yet tested, but VAG-COM should work fine.

[teerak2uk]

i have a friend that has a 2005 A4 which he changed rear lights to original led version but now has error on bulb monitoring is there any way around this via coding either with vag-com or vas


many thanks

[fakirgsm]

more information for fabor

[Code Breaker]

i have a friend that has a 2005 A4 which he changed rear lights to original led version but now has error on bulb monitoring is there any way around this via coding either with vag-com or vas


many thanks

I don't think there is a procedure for that, it's going to be a case of adding resistors to load the circuit so the system then see's a higher resistance.

[teerak2uk]

i did think about that one but surprised that needs to be done as they are genuine audi parts

[Code Breaker]

I could be wrong but, I didn't think the 2005 A4 came with 'original' LED lights, hence your light warning issue.

[teerak2uk]

maybe not 2005 but maybe 06 or 07 as it must be the same shape for them to fit

[Code Breaker]

I have a 2006 A4 B7 and haven't seen any rear Led lights (well decent ones anyway) that don't cause this problem as yet.

[teerak2uk]

i`ll double check what year it is with him tomorrow but i thought there may be a way to code it out of the system

[sawadogo1]

Hello, I'm looking for code for the special function of the Touareg V6 TDI 2005, because I want to adapt the module of the turbo.

13128 control circuit for controller for turbocharger1 ( J 724 )
P3348 No or incorrect basic setting/ adaptation Thank you for your contributions

[dave11674]

hi

i have a mk 4 golf gt tdi
just picked it up
the remote central locking does not work
nor when i put key in lock it does not do the central locking

any ideas ?

thanks

dave

[superc0]

YOUR PROCEDURES WORKS IN ALL CARS?
THANKS.

[Frykas]

Hello i need to do adaptation to a car so i can get speedometer working... its an 2004 audi a4.. we changed the dash cause it was faulty and now need to do adaptation with abs? can anyone tell me where and what value to put in?
Can it be channel 60 in Instruments adaptation? please help me

[cipijoint]

wiki ross tech

[cipijoint]

here is some compressed html procedures for ross vcds. its someting like a website that work offline.

[ovi_dk]

Hi
Can somone explain how can i put off the frog lights on golf 5?:questionmark:Thank u.
B.R

[ghostridersa]

here is some compressed html procedures for ross vcds. its someting like a website that work offline.

Great help thanks

[ghostridersa]

Taillights:

[Select]
[09 - Centr. Elect.]
[07 - Coding]
[Long Coding Helper]

Byte 9: Uncheck all the boxes or change the DEC box in the figure 0 (zero)

[Transfer Coding!]
[Do It!]

Thanks very much for the listed help.

[tiguan]

Hi
Can somone explain how can i put off the frog lights on golf 5?:questionmark:Thank u.
B.R

Select 09 (Central Electronics)
Long Coding -> Function 07

Byte 00 Bit 0 / Fog Lights installed

[sanaxx]

And all the first 14 and more together!