2008 tahoe 15892530 clear dumps

[seed212]

please help me to clear my airbag dumpe for
chevrolet TAHOE 2008
SDM-C ( 15892530 )
EEPROM 95160
THANKS

[Highvolt]

try and report

[AMLGAR]

good luck.:top:.POST Removed did not work.

[seed212]

i will be test and i report by resuit

[seed212]

thanks for all
it is not work
please anther help .

[lwood]

What DTC's did you get?

[jjrp255630]

please help me to clear my airbag dumpe for
chevrolet TAHOE 2008
SDM-C ( 15892530 )
EEPROM 95160
THANKS

try it and report...

[Highvolt]

thanks for all
it is not work
please anther help .
What the DTC you have?
Did you clear DTC b TECH II?
then try this

[seed212]

What DTC's did you get?

i am not check DTC . ONLY THE SRS LIGHT IT IS NOT OFF AND MASSAGE NOT GO .

[seed212]

What the DTC you have?
Did you clear DTC b TECH II?
then try this

OK I WILL BE TRY CLEAR DTC .

[seed212]

try it and report...

THIS DUMP NOT CLEAR

[lawdog1]

THIS DUMP NOT CLEAR


This is 100% clear. But you must initialize it. If you say it is not clear, you are doing something wrong or are not using a proper scan tool.

[AMLGAR]

THIS DUMP NOT CLEAR. STOP THINKING THE LIGHT goes off itself when is clear of crash, some times you HAVE TO clear DTC.:top: NOT ALL . BUT MOST OF THEM. what about if you have a fault code like a short a plug open something like that. you dont know.

[seed212]

after i use scan tool to i check the dtc there is no communication with sdm .

[Highvolt]

after i use scan tool to i check the dtc there is no communication with sdm .
there is something wrong.
make sure for EEPROM soldering , programing, or from SDM it self?

[seed212]

i do solder and desolder for eeprom more than 10 time . i think the bord ~~~~ i will be try repair

[AMLGAR]

why you removed chip try to use a programmer the one support eeprom on board

[seed212]

why you removed chip try to use a programmer the one support eeprom on board


i try read BY UPA but the eeprom lock .
after i read all data 00 00 00 00 00 . etc .

[seed212]

This is 100% clear. But you must initialize it. If you say it is not clear, you are doing something wrong or are not using a proper scan tool.

it is not work with these dtc B0015/16/22/23/33/40 and i make initlize with clear dtc but not work

[lawdog1]

Dear friend,

You may have a problem with the module circuit, sensors, or may still have components that need to be changed.

I am attaching the codes for that vehicle. It is showing both driver and passenger seat belts and head impact airbag faults. These are not crash faults. That means you can go buy a new module, put it in, and you will get the same codes unless the problem is with the circuit in your module.

Did you change the seat belts? Did you change the head impact modules?

Hope this helps you out.

[lawdog1]

Here they are. All of your codes are soft codes, not crash codes. They indicate faults in the airbag system. Make sure you have repaired all of the components.

Seems like your problems are the seat belts, and roof airbags.

[seed212]

Here they are. All of your codes are soft codes, not crash codes. They indicate faults in the airbag system. Make sure you have repaired all of the components.

Seems like your problems are the seat belts, and roof airbags.

my dear
there is method to clear crash date on the memory of AIRBAR ECU and no need to replace any components .

[lawdog1]

my dear
there is method to clear crash date on the memory of AIRBAR ECU and no need to replace any components .


Wow. I think you completely misunderstood the purpose of this forum. We clear and reset the memory so there is no need to replace the AIRBAG ECU, NOT so that it works without replacing any components.

If you do not replace the components, your light will never turn off with any of the files uploaded in this forum. I hope you don't live in the United States, because tricking the car so the light turns off without changing the components is very illegal.

You should not post any more requests in this forum for clearing the memory unless you plan to change the components, because you will be wasting everyone's time.

[greenthumb]

not knowing how the system works. wouldnt it be easier to replace the computer you are trying to reprogram?

[AMLGAR]

HE WANTS TO DECODE THE MODULE ELIMINATING, COMPONENTS, JAJA THIS IS CRAZY. SOME BODY TOLL ME THAT, I DONT KNOW IF IS POSSIBLE, :stupid:

[seed212]

Wow. I think you completely misunderstood the purpose of this forum. We clear and reset the memory so there is no need to replace the AIRBAG ECU, NOT so that it works without replacing any components.

If you do not replace the components, your light will never turn off with any of the files uploaded in this forum. I hope you don't live in the United States, because tricking the car so the light turns off without changing the components is very illegal.

You should not post any more requests in this forum for clearing the memory unless you plan to change the components, because you will be wasting everyone's time.


now i know , what is mean by ' clear crask data '
thanks for your help .
:stoned:

[AMLGAR]

Wow. I think you completely misunderstood the purpose of this forum. We clear and reset the memory so there is no need to replace the AIRBAG ECU, NOT so that it works without replacing any components.

If you do not replace the components, your light will never turn off with any of the files uploaded in this forum. I hope you don't live in the United States, because tricking the car so the light turns off without changing the components is very illegal.

You should not post any more requests in this forum for clearing the memory unless you plan to change the components, because you will be wasting everyone's time.

:goodpost: