swap touareg ecu

[aeroyas]

hi freind's please in need help to swap an ecu from a VW touareg V6 year 2008 i have buy a virgin ecu from volkswagen but when a try to adapt it with Kessy (i have kessy access code) the ecu refuse this code, please is there any special procedure to adapt this ecu? thank's a lot in advance

[toniz]

Dont try to log in to ECU, it is virgin, so it doesnt have a pin yet.
Try this:
[Select]
[01 - Engine]
[Adaptation - 10]
Enter 050 in "Channel Number".
[Read]
For the following procedure, use the PIN of the CAR.
There are 2 possibilities how to enter a PIN, choose the one that applies for you.
4/5-digit PIN
The PIN needs to be entered as 5-digit number. For example, if your PIN is 1234, enter 01234.
7-digit PIN
[Use 7-digit PIN/SKC]
Enter the 7-digit PIN, Date on which the PIN was generated by the dealer, along with the Workshop Code (WSC) and the Importer number of the dealer that generated the code.
[OK]
VAG-COM will validate the data you have entered and return you to the Login screen, where the Login Code will show as "XXXXX".
[Test]
Check the 1st measuring value.
[Save]
[Done, Go Back]
[Close Controller, Go Back - 06]

Switch OFF the ignition and let the car sit for ~1 minute, then switch ON the ignition again.
Verify that the NEW ECU now shows the VIN and if supported IMMO-ID of the vehicle now.

[aeroyas]

thank's a lot freind for your answer but i have try this procedure with no success, when i enter my 5 numbers code, the vag com show me 'not in order', is there ant other procedure please?

[milkatrek]

in this case only online procedure :(
or try make used ecu by bdm and then adaptation by 50 from kessy module.
Please send me this dump from this ecu

[starprog]

hi freind's please in need help to swap an ecu from a VW touareg V6 year 2008 i have buy a virgin ecu from volkswagen but when a try to adapt it with Kessy (i have kessy access code) the ecu refuse this code, please is there any special procedure to adapt this ecu? thank's a lot in advance
hi
send us the dump of this new ecu please
whitch reference of this ecu, use bdm to make copy of ecu.
give us the report too ;)

[snatchme]

please mail eeprom file (95...) of EDC16 or MED9.
can have a look if i can make your ECU virgin.
you can do only the VAG-COM way if ECU is virgin.

Grtz..

[aeroyas]

hi freind's, thank's a lot for your answers, i have try to read eeprom with vag dash but i only have FFFF in all lines, i don't want to open this ecu because it caust 2500 USD, is there any other solution please? any access for virgin ecu's? thank's a lot in advance

[aeroyas]

any help please?

[snatchme]

Sorry only way is opening ECU..
vagdash doesn't read/write compleet eep file,just a part of it.

opened these load of times, is no problem..
if you send me file make it virgin for you..

Grtz..

[chriskross]

you can read eeprom in ecu with vag k+ can commander

you also can clone it.

[aeroyas]

i have try with vag commander too, no way, i think there is protection on this eeprom it's 2009 one

[chriskross]

i have try with vag commander too, no way, i think there is protection on this eeprom it's 2009 one


Hello which version do you have of VAG commander?

[Maartinj]

Dont try to log in to ECU, it is virgin, so it doesnt have a pin yet.
Try this:
[Select]
[01 - Engine]
[Adaptation - 10]
Enter 050 in "Channel Number".
[Read]
For the following procedure, use the PIN of the CAR.
There are 2 possibilities how to enter a PIN, choose the one that applies for you.
4/5-digit PIN
The PIN needs to be entered as 5-digit number. For example, if your PIN is 1234, enter 01234.
7-digit PIN
[Use 7-digit PIN/SKC]
Enter the 7-digit PIN, Date on which the PIN was generated by the dealer, along with the Workshop Code (WSC) and the Importer number of the dealer that generated the code.
[OK]
VAG-COM will validate the data you have entered and return you to the Login screen, where the Login Code will show as "XXXXX".
[Test]
Check the 1st measuring value.
[Save]
[Done, Go Back]
[Close Controller, Go Back - 06]

Switch OFF the ignition and let the car sit for ~1 minute, then switch ON the ignition again.
Verify that the NEW ECU now shows the VIN and if supported IMMO-ID of the vehicle now.

How to do in V10 engine when you have 2 ECU-s and both was exchanged ?

[klonone]

Hello, i have same problem ,not posible swap ecu touareg bks edc16cp34
please help