need immo location

[grinovsky]

hi all mumbers
i have this ford delphi ecu to change with other second hand
but i don't find immo location to bypass
where is it?

[dickymint]

soic8 ST device next to corner of mpc, it is 95160..

[firestator]

hi all mumbers
i have this ford delphi ecu to change with other second hand
but i don't find immo location to bypass
where is it?

it is 95640..

[grinovsky]

thank you very much gays
i have an other question :
the out voltage from ecu to injectors is 6v and not 12v:banghead:
some one have repaired this ?:hmmmm2:

[ammarben]

if it is diesel it should be about 80V to 110V
you can test it with oscilloscope

[grinovsky]

if it is diesel it should be about 80V to 110V
you can test it with oscilloscope

this is right in HDI engine (siemens injection)
in delphi injection the injectors must be powered with 12v and 25A
i tryend to remove 1st condensator but same think!

[ammarben]

is it ford tdci?
what problem have engine?

[grinovsky]

yes,it's ford focus 1.8 tdci break
the probleme is after repared the injectors by delphi center
they bloqued open one after the ather and engine want start by he can't
so i checked impulse injector by oscilo and i find that not go more then 6volt,i cheked too voltage at connector injector at ignition and same think 6v
the ecu out to injector is 6v and not 12v!!!

[ammarben]

as i know if one injector is faulty the ecu block the injection
try to find wich injector est gripp? comme on dit en fran?ais
and replace it

[grinovsky]

c'est moi qui est gripp? et non pas les injecteurs

[grinovsky]

it's impossible that injectors continus to work normaly with 6v power,they will be blocked

[ammarben]

Ne te fache pas l'ami ?a va s'arranger in the end A toute peine fin

[ominimicu]

I think you have a Mosfet going bad.

[grinovsky]

I think you have a Mosfet going bad.
hi omnimicu
i checked the two BUK9219 55A and they are good
is there other think to check?

[odyseus7]

I think with 95640 swap only not work .This car have often problem with crank sensor.

[grinovsky]

I think with 95640 swap only not work .This car have often problem with crank sensor.
do you speak about this?

[grinovsky]

is it possible to make immo off for this ecu2M5A-12A650-PF?

[grinovsky]

HELP PLEASE

[ecutuners]

hello you need to flash in the processor content aswell, the 8pin soic alone is not enough

[grinovsky]

ok i will try to read mpc555

[grinovsky]

so i read the processor and this is the result:
configuration A
configuration B
few bits and all others FF
so one have a dump for this processor?

[grinovsky]

AND THIS IS THE FLASH, is there any solution?
help please

[grinovsky]

help please gays it's an angland car

[rapkopat]

hi guys need immo location for this ecu. not 95640( 12237906-16a) immo.

[kugglefischer]

hi omnimicu
i checked the two BUK9219 55A and they are good
is there other think to check?

hi
what are the oem marking on the 2 X mosfets for the injectors?

thanks!

K

[baltazar3]

it's impossible that injectors continus to work normaly with 6v power,they will be blocked
Have once that the bad starter run down voltage when cranking.Check that !