VW Polo 14 from 1998 To add another ecu and key

[jfiljak]

I have a question whether it is possible to pair, ECU Bosch MP9 VW POLO 1998g and immo box TMS370 pin 0248, and the key IC PCF79935
All the other cars.
I have VCDs 10.6 Vag Commander, and UPA USB.ALL-11

I have danp (immo of) for the ECU but my programmer - ALL 11 can not wraite 87c510 an error



Thanks

[jfiljak]

http://www.speedyshare.com/files/28238823/POLO-14-BOSCH-844-EPROM-87C510-T.dec (http://www.speedyshare.com/files/28238823/POLO-14-BOSCH-844-EPROM-87C510-T.dec)

SORRY

[Autofix]

Not sure wht you want to do bit i think you want to swap an ECU. this is easy, no coding needed, just reset adaptions.

Here - Immobilizer II ECU Swapping - Ross-Tech Wiki (http://wiki.ross-tech.com/wiki/index.php/Immobilizer_II_ECU_Swapping)

[jfiljak]

That are installed new ecu and immo box but the other car
Bosch number is the same and the Ecu and the IMMO
Vag com accept login Immo code in 25 channel and re-type 0 keys
But the engine 01 accepts the login at 11 463 and does not allow adaptation

[Autofix]

There is no login needed in this engine ecu.

I had this same problem with vag com a few years ago. Older versions of vag com would work without login, i did loads this way, so I used another scan tool (carman scan) and worked first time.

I just checked my records and mine was also MP9.

to be clear, older versions of vag com did not need a login to allow adaption channel 00 be reset but later versions did.

Use another tool or a very old version of vag com. Simply reset adaptions channel 00 to 00. Switch off ign, switch back on but do not start for a few minutes. Try it and see.

[jfiljak]

To reset the ECU 00 allows channel 00, something was making a mistake because immo persists errors 2
We go to 00 246 immo login is accepted, Channel 1 entry of 01 keys

Why error occurs Pickup Coil D2

Immo box and the keys are not paired
Vag Commander says that China is paired but the error remains
http://www.speedyshare.com/files/28250202/ECU.bmp (http://www.speedyshare.com/files/28250202/ECU.bmp)
http://www.speedyshare.com/files/28250213/IMMO_1.bmp (http://www.speedyshare.com/files/28250213/IMMO_1.bmp)

[Autofix]

Ok, first you must code the keys into the immo box. Read this carefully - http://wiki.ross-tech.com/wiki/index.php/Immobilizer_I_Key_Matching_(Separate)
remember to check immo block 001 to check if the key is ok. If you have a faulty key, or a wrong key, or a faulty pickup then you will not be able to code the key.

Then, when keys coded ok, not before, you must reset adaptions in engine ecu (save 00 to 00).

[jfiljak]

It is true that I have a key 2 pieces from other cars and 2 Immo box,
I replaced the pickup but not the key pairs and Immo box
Is it possible to pair the key from another car and Immo box from the third car Thanks for the help so far

[jfiljak]

Is it possible to repeatedly pair Pcf79935 chip Golf 3 Polo, with immo boxing from other car I am trying but can not
hello

[jfiljak]

Everything was opened with paired immo box and key from another car
and vag-com ecu channel 0 00
Thank Autofix