immo off sim32

[mecano_diag]

i need immo off for renault clio siemens sim32
or any solution for start engine because the uch is dead
thanks for your help

[alfabit]

i need immo off for renault clio siemens sim32
or any solution for start engine because the uch is dead
thanks for your help

29F200 desolder, read, virgin dump, rewrite back to prom, use emu ( if necessary , you are lucky no need emu ) cut wire 58.
Simple isn`t it ? 1 hour make emu, 1 hour read-write prom, total 2 hours work ( if you have the necessary skills and tools ).
If you can`t virgin dump put it here and some good guy will virgin for you.

[mecano_diag]

29f200 in sirus 32 not in siemens sim32
this ecu immo in 95160

[alfabit]

29f200 in sirus 32 not in siemens sim32
this ecu immo in 95160

I wish you good luck with that siemens sim32 !:stoned:

[ceyhan]

sim32 64F7055F40 flash read

[mecano_diag]

problem solved,thanks for all

[ceyhan]

how to solve

[alfabit]

sim32 64F7055F40 flash read

Are you sure it must be read that monstrous " centipede " ?
Mecano_diag spoke about a SPI 95160 prom !
It`s awfully reading that MCU or prom or whatever is !

I saw two SOP8 nearby, maybe immo is there .

[elektor72]

use carsofware 5.0 to remove immo

[elektor72]

try this immo

[morfej]

Elektor72: if you havent notiec mecano_diag meant sim 32 not sirius 32, totaly different engine ecu.

Br

[elektor72]

use this immo_off and say thanks please
tested ok on clio3

[elektor72]

immo_off test on clio3
say thanks

[elektor72]

immo off for clio3 say thanks

[leandroks]

If any1 still need the sim32 immo off here is the dump..
It is an 95160.
Dont forget to cut the immo wire.

BR:hello:

[rodinhas50]

What is the numbers of immo wire?

Thanks

[Formator]

What is the numbers of immo wire?

Thanks
Renault on SIM32, there is no specific line immobilizer.
It passes through multiplexing.

Sur les SIM32 Renault, il n'y a pas de ligne sp?cifique antid?marrage.
Cela transite par le multiplexage.

[rodinhas50]

Like i think... Immo by can...

BR

[leandroks]

Works ok if u connect with immo wire on it will code automatically if u want it immo off just cut the CB2 wire.. Cheers

[darwins]

Hi

ESI says:

CB2 = engine speed
CB3 - Anti theft alarm control

Can anyone confirm their experience !
I'm thinking a selflearn is taking place in most cases and it is not immo off..

Can anyone 100% confirm total immo off with a wire cut or not ?

[Formator]

Hi,

D4F772 and 774 on the Renault Twingo II, there is no line encoded.
Track B3 of the black connector 32-channel is not used.

Darwins, that is what as a vehicle that you're referring to about the estate in line CB3 ?
Dacia perhaps ?

Salut,

Sur les D4F772 et 774 des Renault Twingo II, il n'y pas de ligne cod?e.
La voie B3 du connecteur noir 32 voies, n'est pas utilis?e.

C'est sur quoi comme v?hicule Darwins, que tu fais r?f?rence pour parler de la ligne immo en CB3 ?
Dacia peut-?tre ?

[darwins]

Clio 11

All other are obviously CAN

Thanks for taking the time to post.....:tee:

[Becoacamba]

immo_off test on clio3
say thanks

hi thanks for de file, but not work. have to do something more?

[darwins]

I think this will only work with Clio 2 where immo line can be cut.

If Im wrong I stand to be corrected :)

[ninja123]

I tried to immo off sim32 a few months ago, i came to the conclusion - NO IMMO OFF!

Get your multimeter out and find broken wires and repair, only solution.

ninja

[iwen31000]

the solution is simple, you must find a ecu and uch , you copy the eeprom 95160 and flash of mcu , you also copy the eeprom of uch and after its done you a copy of the key

[rockauto]

I have been doing some tests here and with the immo file out of the possible in tests outside the vehicle the following is occurring ... When I record the immo file off at 95160 observing what is connected to the ignition or the relay of the bomb normally arms by 4 and then no longer works until it completely cuts out there, the system will run again for 4 more times. italy in cutting the +30 and joining with +15 so that when you turn off a system ignition always re-start any tips? I'm going to test in the car and see what happens.
I have been doing some tests here and with the immo file out of the possible in tests outside the vehicle the following is occurring ... When I record the immo file off at 95160 observing what is connected to the ignition or the relay of the bomb normally arms by 4 and then no longer works until it completely cuts out there, the system will run again for 4 more times. italy in cutting the +30 and joining with +15 so that when you turn off a system ignition always re-start any tips? I'm going to test in the car and see what happens.I have been doing some tests here and with the immo file out of the possible in tests outside the vehicle the following is occurring ... When I record the immo file off at 95160 observing what is connected to the ignition or the relay of the bomb normally arms by 4 and then no longer works until it completely cuts out there, the system will run again for 4 more times. italy in cutting the +30 and joining with +15 so that when you turn off a system ignition always re-start any tips? I'm going to test in the car and see what happens.

[ricketts0121]

Will this work with my Clio mines a sim32 Siemens Clio 1.2 2008