Mazda 3 ('10) - BCP8 57K30 - reset needed

[angelo44]

Need help resetting the airbag module for a 2010 Mazda 3. Dump attached.

Many thanks guys!
A

[angelo44]

Anybody? Can this be done?

Thx
A

[sawatdee0999]

Here is your clear data. Report back after you tested.

Pass in PM =)

[angelo44]

Thanks sawatdee0999 !!!!

I will get back with result by end of week.

A

[sawatdee0999]

Okay, I will wait for your result. If that first one dont go off 100% try this one.


Pass is the same as first.

[bender]

Could I have the password, please.
I think my module is no good.
I cleared myself. everything workok except
3 sensors got no respond whether I connect a
resistor or open circult(show 0Ohm instead of 9.99)

[credoline]

i do not think that sensors you can imitate with resistors

[sawatdee0999]

Could I have the password, please.
I think my module is no good.
I cleared myself. everything workok except
3 sensors got no respond whether I connect a
resistor or open circult(show 0Ohm instead of 9.99)

you cant use resistors for sensor since they are built with mercury inside. Get a new sensor. If that don't work. Send you crash file. Mazda Airbag module carry vin. it would be tricky just giving you a clear file of a other module. If you don't have a crash file. Send that clear file i will rewrite it.

[bender]

you cant use resistors for sensor since they are built with mercury inside.
YES, you can use resister to simulate the sensor but
I only use it on the Belt pretentioner or buckle sensors ONLY.
Never on the Airbag Modules which are possible TOO!

Get a new sensor. If that don't work.
Absolutely, if the Airbag modules have been deployed or the impact
sensors are no good sure you must replace it for
reasons I'll not elaborate.

Send you crash file. Mazda Airbag module carry vin. it would be tricky just giving you a clear file of a other module. If you don't have a crash file. Send that clear file i will rewrite it.
Thank you for offering to help me, let me mention, I already cleared my
crashed dump base on the previous crashed & good dumps you'd posted but different module number.
Yes, I did retained the Vin#



I think my Airbag Controller(SAS) hardware is no good. Actually
I got 4 sensors not responding. The rest respond to if I connect
the sensor or disconnect the sensor it will show in my scanner
if I disconnect it will show disconnected & if I connect, It will show
Connected.
Anywhere I attached my crashed dump & I'll hope for the best!

[sawatdee0999]

You can use resistors like for your Belt pretentioner or buckle sensors, airbags in seat, front airbag and side airbag. But not for sensors like impact sensors, Because they read differently. Which sensors are bad? Side Impact sensor right or left or is it Front impact Right or left.

Here your clear file. Try it. Report back

Good luck Bro,

Pass in PM

[bender]

Same problem. I think hardware problem.

[sawatdee0999]

I think it could be as well.

[angelo44]

Same problem. I think hardware problem.


hey bender,

here's the dump that worked on a few modules (irrelevant of the VIN number). however, it sounds that you may have a hardware problem (pinched lines, missing ground, faulty sensors?...)...

good luck and let us know how it turned out.
A

[bender]

hey bender,

here's the dump that worked on a few modules (irrelevant of the VIN number). however, it sounds that you may have a hardware problem (pinched lines, missing ground, faulty sensors?...)...

good luck and let us know how it turned out.
A

No good too. I attached a good dump for yours. If the other 2
not going to work try mine. If mine works, It'll confirm my Hardware faulty.