Rover pektron help

[obdmaster]

Hi can someone help me add these two remotes to dump attached.

Barcodes are as follows.

N5983C060040506238143G

N6A83C060040506237865S



Many thanks

Obd

[PierreTheron]

Hi just need to change hard disk then i am onto it..

Pierre

[skitszo1]

Dump is not correct or corrupt, what did you read it as, should be read as microchip 93LC66A

[PierreTheron]

Hi

Seems file is not correct. Read as 8 bit . Upa Usb...

Cannot even see pincode in it


Pierre

[obdmaster]

Will read as 8 bit in morning .

Thanks guys

[obdmaster]

Re read 93c66 in 8 bit now i can see chassis NO in dump

Please if someone could add barcodes for remotes, that,ll be great.

Barcodes are as follows.

N5983C060040506238143G

N6A83C060040506237865S

Many thanks

Obd

[parapilot]

Here you go mate,

[PierreTheron]

Hi

Parapilot where is your zeros before and after barcodes.


Obd

Pincode 9895

Here correctly added barcodes.

Please note that old remotes are not wiped and can still work.

If you need to remove them you must use T300 to go through programming with both new remotes at the car.

Pierre

[parapilot]

dont need them mate, my dump is 100%, iv written in hundreds like this.

J

[nutloose]

here you go

[obdmaster]

I have parapilots dump on chip, so i will let customer test.

I will post results, thank you parapilot, pierre and nutloose

[nutloose]

OOPS sorry, I just checked my dump and only the one fob had been added.
I have just edited (and checked) so use the edited version for both fobs.

para's dump looks good first time though....and so does Pierre's

[cjawahir]

can you just add this remote with ad 100 , or mvp clone ?

cj

[parapilot]

You can providing the alarm system is dis armed. Ie you have a working remote. If all are lost then they need to be written in. Eka rarley works.

[obdmaster]

Customer says only one fob working with parapilots dump, do you guys think its worth trying pierres or nutlooses dump as they are litle bit different with 00 instead of ff,s around barcodes.

But customer got fobs off ebay but he said they were sealed is it normal for mg rover to put wrong barcodes on packet???

[PierreTheron]

Hi

Eka always worked for me provided the doorlock is in full working condition.

Disconnect hooter while you are doing the eka input procedure.

[PierreTheron]

Customer says only one fob working with parapilots dump, do you guys think its worth trying pierres or nutlooses dump as they are litle bit different with 00 instead of ff,s around barcodes.

But customer got fobs off ebay but he said they were sealed is it normal for mg rover to put wrong barcodes on packet???


Can customer bring vehicle to you now, or does he stay to far away.

Use T300 or MVP to add remotes again..

Ask member ninja123 He has been studying these dumps and might be master on them now.

Like adding foofoo valves ,window washers ,bootlock ,smokelights without testbook..


:D:D:D

[ninja123]

Customer says only one fob working with parapilots dump, do you guys think its worth trying pierres or nutlooses dump as they are litle bit different with 00 instead of ff,s around barcodes.

But customer got fobs off ebay but he said they were sealed is it normal for mg rover to put wrong barcodes on packet???

I ONLY JUST SPOTTED THIS THREAD!!

Barcodes are 100% correct, just add 1 remote to dump, and as pierre stated, you must change ff to 00 where stated, then plug unit to car and remote will dis arm immo, then use t300, mvp to add next remote and also re activate old fobs too!
Adding 2 remotes to dump has never worked, tried about 50 times now and only first remote works, but all good after mvp input!
Also, in dump, you need to change the last entry after code.
ninja

[v8 dave]

Do you always put remote codes in position 1, or do you put them in the other fob positions?

[PierreTheron]

[QUOTE=ninja123;1174326]I ONLY JUST SPOTTED THIS THREAD!!

Adding 2 remotes to dump has never worked, tried about 50 times now and only first remote works, but all good after mvp input!


Thank for info m8.

With the software i got i can add 2 remotes and both works after it was done that way .(just remember the software does not remove the old remotes ,it just lets you add new remotes into the dump and both works without using MVP)

Old,lost remotes can be de- activated with MVP..

Pierre

[PierreTheron]

can you just add this remote with ad 100 , or mvp clone ?

cj

You can just add a new remote with MVP provided that you have working remote.
All remotes that needs to be activated must be with the car when adding them with MVP. Just follow instructions and go through the whole procedure( Do not unplug or disconnect)

If all remotes are lost you need to input EKA code or add barcode to dump before the SCU will unlock....

Hope this helps:questionmark::tee:

[ninja123]

Do you always put remote codes in position 1, or do you put them in the other fob positions?

Always add into next position, this method never failed me, but adding to original postion fails lots of times.

ALSO, when reading out the old barcodes, they never work when programmed into another unit, so poss that the code gets changed????

If write complete eeprom content, then the old remotes will work!!

BUT, after programming in a new remote with known barcode, this code remains the same in the dump?:hmmmm:

ninja

[parapilot]

you do not need to change the FF to 00! it works either way as blank data. To disactivate remotes in the dump, change the 01 at the end of the barcode string to 02.

[gtmech]

Hi can someone help me add these two remotes to dump attached.

Barcodes are as follows.

N5983C060040506238143G

N6A83C060040506237865S



Many thanks

Obd

hi mate, where did you get the barcodes from and the dump you have read is from which control box? this isnt from a Rover 75 im guessing yeh?

[ninja123]

hi mate, where did you get the barcodes from and the dump you have read is from which control box? this isnt from a Rover 75 im guessing yeh?

Sorry M8, this is pektron (rover 25 45 mg zr zs)
75 using bmw EWS

I could do with knowing where codes are stored too!!

ninja

[Meat-Head]

Adding 2 remotes to dump has never worked, tried about 50 times now and only first remote works, but all good after mvp input!
Also, in dump, you need to change the last entry after code.
ninja

Original poster, hope your taking notes :roflmao::roflmao::roflmao::roflmao::roflmao:
You will shortly be able to, prove or disprove this therory for yourself.

Just need winzip and to upload them

[pianoman58]

Rover75 barcodes are held in Bcu, its behind glove box, similar to bmw GM unit

[ninja123]

Rover75 barcodes are held in Bcu, its behind glove box, similar to bmw GM unit

What eeprom is inside bcu??

ninja

[Meat-Head]

What eeprom is inside bcu??

ninja

* IF * remember and can find it, there is a new one at M-H-M.

It was ?160+VAT ish - don't ask questions, all you need to know is we got away with it.

*THINK* it's was a arse stonking proceseer

[Meat-Head]

You can just add a new remote with MVP provided that you have working remote.
All remotes that needs to be activated must be with the car when adding them with MVP. Just follow instructions and go through the whole procedure( Do not unplug or disconnect)
s:questionmark::tee:

FETISH * BUMP * SPAM ETC * ETC.

Can you tell us, how to do this with MVP, please, what version is yours please?

what was that website the pektron software is on?

Meat.

[PierreTheron]

FETISH * BUMP * SPAM ETC * ETC.

Can you tell us, how to do this with MVP, please, what version is yours please?(Do not know):devil:

what was that website the pektron software is on?--keyprogrammers.com

Meat.

Hope this answers itt..:ciao:

[Waynew]

can anyone help to paste this barcode into scu dump please?
the barcode is N423F24690410321435049
thanks

[PierreTheron]

can anyone help to paste this barcode into scu dump please?
the barcode is N423F24690410321435049
thanks

Here mate..

EKA is 2561

[Waynew]

thanks
:proud:

[InfoPerformance]

The original remote has stopped working, due to lack of battery, how can I do to work again? Thank you.

[Meat-Head]

Tried reading handbook? Or ignition on press buttons like a retard?

[PierreTheron]

Pectron soft for adding barcodes you get from the guy that does wonders to renaults back in the days .
Keyprogrammers.com .
with there software certain barcodes while adding adds ff to it ... But you can add two and write to dump and both will work 100 %

[PierreTheron]

hi used keyprogrammers soft and now after few laptop replacements i am asking a hacker to unl0ck this software .. he can PM me to get original soft that is not working . i am in South africa and made just about double my money back on these vehicles as i ask cheap on old vehicles

[Meat-Head]

Go stalk DK member. Blackpirate He was part of the team that cracked the program we are not allowed to talk about

*THINK* go stalk member drpeter (spelling vip member in mileages section )
*THINK* he had thread. “Opel gold” that programme that makes demo programs unlocked by running it first