Experience with Autocom

[bibkare]

I oredered two chips M6636B from ut source, waiting to come, let you know what happened

[dimitar22]

I need pinout from the man 37 pin cable please help me i need to know on which pin from the obd cable goes to which pin on the 37 pin cable so i can use it with original man interface.

[bibkare]

I oredered two chips M6636B from ut source, waiting to come, let you know what happened

Chips came, tomorrow test on car

[damiantucha]

I need pinout from the man 37 pin cable please help me i need to know on which pin from the obd cable goes to which pin on the 37 pin cable so i can use it with original man interface.


please check it
In autocom k line should be on 3 pin
Please raport

[bibkare]

Chips came, tomorrow test on car

Mondeo 2001 and KA 1999 not working, i didn't test it on newer CAN based, something else has to be done besides soldering OKI chip on board

Update:

i got tip to change 39 ohm resistors to 390 ohm which i forgot, so another test is coming


Update:

After changing resistors i was able to diagnose everything except engine. Car was mondeo 2001 2.0 diesel, other modules AC, airbag, ABS,instument, immo all went fine. Any suggestion welcome

[alfy]

Better tell us how to activate or get an keygen to do that.
:D


Can help, contact me in PM...

Regards.

[proel]

OKI IC is "made in" from thai or japan ? if you can access immo, there should not be problems with the engine ...


Mondeo 2001 and KA 1999 not working, i didn't test it on newer CAN based, something else has to be done besides soldering OKI chip on board

Update:

i got tip to change 39 ohm resistors to 390 ohm which i forgot, so another test is coming


Update:

After changing resistors i was able to diagnose everything except engine. Car was mondeo 2001 2.0 diesel, other modules AC, airbag, ABS,instument, immo all went fine. Any suggestion welcome

[jjrp255630]

hi, anyone knows where is the problem to autocom trucks dont work in volvo and in iveco? i already fix the cables but the problem is on board

regards

[alfy]

hi, anyone knows where is the problem to autocom trucks dont work in volvo and in iveco? i already fix the cables but the problem is on board

regards


What protocol uses this trucks to comunicate?

[xdamdamx]

Is there any solution for those not-working with BMW's around 2004-2007 year? Yesterday I had an E90 , it didn't communicate at all. Only generic OBD.
I have OKI inside, resistors 390R.

[jjrp255630]

What protocol uses this trucks to comunicate?

obd protocol

[worldiagnostic]

Guys, any source to buy a set of CDP TRUCK cable adapters with CORRECT PINOUTS? Without exceptions! :)

[tk500]

Guys, any source to buy a set of CDP TRUCK cable adapters with CORRECT PINOUTS? Without exceptions! :)

Home - Autocom (http://www.autocom.se)

[chrismoore02]

Hello guys im looking at getting a clone Autocom CDP cars with OKI M6636B chip, can the same unit do trucks? is it just the software different or is the hardware different?

[paro44]

Hello guys im looking at getting a clone Autocom CDP cars with OKI M6636B chip, can the same unit do trucks? is it just the software different or is the hardware different?

Trucks have 24 volt (or some more), some interfaces have capacitors rated for 25 volt, that could be not enough and interface can be damaged.

[chrismoore02]

thanks for your help i have orderd one now with 25 and 35v capacitors so will see what its like when it turns up (has the truck software been posted on here)

chris

[didi_du_93000]

My one full working.... If you would like picture of pcb i can do it.


Sent from my BlackBerry 9900 using Tapatalk

[chrismoore02]

if you could post a pic i will compare it to the one i have ordered fingers crossed it will be ok

[jorge]

Hello DK?s

How to update your Autocom CDP....

To update your Autocom CDP interface to Realise 3, 2010
- Hardware ID and key to install on PC
- Hardware ID and key to install on Pocket PC
- dump to ATtiny
- dump to 29F800

Pass in PM ):


Please can you send me the password? Your pm is full.
Thank you

[rabihfiras]

Kindly Need The Password.. Tks. 4 Sharing.

[mariane51]

Can anyone give me some pfd or docs on how to use autocom? Thanks in advance.

[Joe019]

Any way for use the autocom trucks interface clone with cars software?

[michalez]

Any way for use the autocom trucks interface clone with cars software?

Just change sn and it will works . Type in search autocom 2 in 1


For this who is searching dump for attiny look my posts

[ECUdza]

Hello DK?s

How to update your Autocom CDP....

To update your Autocom CDP interface to Realise 3, 2010
- Hardware ID and key to install on PC
- Hardware ID and key to install on Pocket PC
- dump to ATtiny
- dump to 29F800

Pass in PM ):

Hello, I need pass for dumps. Thx

[obd.tech]

didi_du_93000 can you post the pictures and info of the supplier/when purchased etc

thanks obd

[fluorescent]

I will buy this one, seems to be a good quality:
Buy Autocom for Cars, AUTOCOM pro, AUTOCOM pro cdp, [2012 Good Quality] Autocom for Cars (M6636B OKI Chip) can do almost ford model at Aliexpress.com (http://www.aliexpress.com/fm-store/208026/211226224-524288463/-2012-Good-Quality-Autocom-for-Cars-M6636B-OKI-Chip-can-do-almost-ford-model.html)
If somebody have a good supplier, with good quality products please post here or PM.
First what im doing, when i buy clone tools, i open it and remake all the pcb solder point, reforce all, here is one of the diference between original and clones.

[michalez]

Auto Diagnostic Tools & Auto Key Programmer shop | Nandtools (http://nandtools.com) here you have good version with software 2011-3 in good price. I recommend this seller . Br

[zogo]

Hello everyone!I have a problem with autocom CDP cars.I think that a problem is in one protocol.I can't connect to some cars(ford mondeo endura,astra G...) .I changed 9241 but it still isn't working.I have programator for 29f800 and dump but I dont know what else needs to be replaced. Do somebody know how to fix this problem???THANKS

[autocargo]

Hello everyone!I have a problem with autocom CDP cars.I think that a problem is in one protocol.I can't connect to some cars(ford mondeo endura,astra G...) .I changed 9241 but it still isn't working.I have programator for 29f800 and dump but I dont know what else needs to be replaced. Do somebody know how to fix this problem???THANKS


If you look around this forum you'll find many post's about autocom and problems/faults arisen to users and fixes that worked for some members. There are many reasons your interface would not work. Do some reading m8... everything is here... Check carefully your boards for soldering, missing components (OKI chip) wrong value resistors, faulty relay's... etc.

[mattydr67]

In one word the Autocom clone it is a great sh...t
Good luck

[autocargo]

Always is best to buy original...if you can afford it. And you get good quality interface,free updates and technical support. And will support the producer to develop further... On the other hand some members here got lucky and received good clones and they are happy with it.

[zogo]

hello need pass for dumps thanks

[fluorescent]

somebody have pics of original board to compare with some clone?
If you have please post good pics high quality if you dont mind.
I think the diference is in the components and i want to change some important of them.I promise pictures and info.Cheers.Thanks everybody to this wonderful forum.

[fluorescent]

The problem with the clones is the provider make 60% of the work and we make the 40% by fiding the errors and posting here,they test his crap with us.
I wonder how many chinese are in this forum?
If i post that i want to buy 1000 pieces of autocom clones i am sure that i receive more than 2000 private message.
But the worst thing is, there are good providers get stolen by others and finaly you dont now where to buy.

[fluorescent]

In one word the Autocom clone it is a great sh...t
Good luck

Yes you have right but the original is a s..it with class.

[mattydr67]

Yes you have right but the original is a s..it with class.

Well it hasen't a very good coverage but the hardwear it is good.
The price it is very good for a genuine multibrand tool
Take alook here
.: ALEXON :. [ AUTOCOM - Testere si echipamente diagnoza (turisme/camioane) ] (http://www.alexon.info/automotive/produse/autocom/)
It is 655 Euro + VAT
And a OP-COM genuine it is 540Euro + VAT
Here it is
diag.ro - Diagnostica la nivel profesional (http://www.diag.ro/products/opcom.aspx)
Now you see the difference.
Delphi it is the same but if you have a genuine one it is good.
I worked 1 year with Delphi DS100 and my frined Tapiru had now one and use it with new softwear version and it is good enough.
I said that the Autocom it is a sh..t becasue a lot of hardwear issues.
Who has a good clon is happy now.
Good luck

[fluorescent]

There is a difrence between clone and original one?, i meen the hardware and component location?
I want to buy a clone and change some critical components by good brand ones and see how much time he works.
I work like electrician here in Spain and i have a lot of genuine components, good quality.
Before testing i want to change this components until is to late to see how is working and how long.
We can make a good post here with the results and what is have to be change to have a good clone.

[fluorescent]

I want to advise i am nothing against the original tools but i think this prices for a newbie is to high.
I always recomend to buy original but the political of original brand is wrong, is like a printer they give us almost for free the printer and they make good money with the ink"s.
You buy the tool and in one year you find your tool obsolete, out of buisness.
You spend a lot of time to learn how is it works and all the triks and before one year another tool is coming and another software.The diagnostic protocol of the cars is the same from a few years why you change the software and the tool?
Very simply...to make money and eliminate clones.
Take a example with the AUTOCOM for trucks they change some capacitors and you have another good tool to buy.

[alfy]

The problem with the clones is the provider make 60% of the work and we make the 40% by fiding the errors and posting here,they test his crap with us.
I wonder how many chinese are in this forum?
If i post that i want to buy 1000 pieces of autocom clones i am sure that i receive more than 2000 private message.
But the worst thing is, there are good providers get stolen by others and finaly you dont now where to buy.


Too may are here, yes!
And to mouch help is given to "users" with few posts and all of theme is "need help" or "need solution"!

Thats why I won't post solution for OPEL (pre 2004) and BMW (2004-2007) here!

Sorry M8s, but to many stolen knowledge is going on here... :(

[chrismoore02]

Ive got my Autocom now tried on Audi S3 - OK VW Golf 3 - OK Mercedes W202 - OK Ford KA - cant talk to ECU the unit has the Thiland OKI chip but resistor values on R74 and 75 are 390 so therefore 39ohm going to replace these and try again

is there anything else i need to check on my unit?

thanks
chris

[flavyus1987]

I have Autocom cars with soft version 2011.1 about 6weeks ago.Using it with Asus EeePC 900HA, 1.6ghz,2gbRAM,160HDD, 2 batteries. I'll tell you a little story.
Works perfectly on(after i learned to use it and playing with the years and model cars):
- mercedes w168,w203 = all modules
- renault Espace III 2.2dci 2002 = all modules=engine and brake on software (CAN)
-WV polo 1.0 '96, golf3 1.6 ''97 =all modules
-ford focus 2005 = all modules
- Dacia Solenza,Logan = all modules
-opel astra G&H =all modules
-alfa romeo 156 1.9jtd 2001 = all modules
-bmw 318d 2005 DDE5 = all modules
-fiat stylo 1.9jtd =all modules

Problems was on:
-chevrolet aveo 1.4&1.2 - have only generic OBDoption on software PC = use engine ecotec from opel =works (but another option is ELM or VAG in OBD/EOBD- i use vag 7.04= it is very stable, show more live data like autocom)

When i received the Autocom i installed it on my mercedes A140 '98, and after instalation i setup the bluetooth adaptop (a very cheap model = 3euro, small like a nail).
The password of wifi conection is not "0" - one zero (like in manual), THE CORECT PASSWORD IS 4 ZERO - "0000".
After this i made tests to the cars of my neighbors.That was the time when i learn to use it (using it only with BT conection, more confortable)
Problem was on ford focus 1.8tdci 2001, won't work on engine ( "Not suported..." ) ; when i see this i don't try others module because i thought if not work on engine, it will not work on other module.
I say OK, no problem, for one car...
I test on ford tranzit 2002, the some problems, but i tryed the BRAKE, and the airbag(had error)...the same problems....OK...
Anyway, i hate Ford cars.
But after i tested on Focus from 2005 and i received a massage like "restoration conection with control unity" after playing on the menu, i thought the problem was from my BT usb adaptor=to slow, in that moment i put the cable/wired conection , and wow...very fast respons,very stable(on wifi have a lag time)
I go quickly on tranzit and it works to conect on wired conection and erase airbag error.
I bought another BT adaptor, more faster end more expensive, and all it's fine now, but I waiting now to test again on focus from~2000 to see if it works with new BT adaptor or cable.

I don't open the case because it have a seal on a screw.And my interface is looking like in the first day, without a scratch, because I use it on a little bag.


I have a friend which have the same interface from the same seller, but of him not logged in a BMW from 2006 2.5diesel with DDE5(I don't remember if was 3 or 5 series), the same system like 318d 2005 DDE5.

Same problem on Deawoo Matiz with ALDL conector 12pins.Me too, i have this problems, not logged in with ALDL adaptor.And Deawoo Cielo is not on the list of software.
We don't try on a native OBD2 Deawoo.

In conclusion i belive we need luck to have a 100% functional interface.It is a general interface, and it's normal to appear some errors.This interface working on many models of cars and trucks, on many years and systems; have to much component.It;s very hard to make something perfectly in this conditions, to be cheap and ....CLONE ....and ..... :)
For example KTS from a service Bosch can;t synchronize a new key with Audi A6 from '98
For performance you need dedicated interface on the mark.

Sorry for my expression, I hope you can understand what I wrote.

[dmkom]

Hello DK?s

How to update your Autocom CDP....

To update your Autocom CDP interface to Realise 3, 2010
- Hardware ID and key to install on PC
- Hardware ID and key to install on Pocket PC
- dump to ATtiny
- dump to 29F800

Pass in PM ):

Please for the password file
Thanks in advance

[josecalmgomes]

And now...
AutoCom CDP Cars 01-2011(link)

pass by pm


Thank you for share, send pass, please

[MOBILTRONIC]

Hello DK?s

How to update your Autocom CDP....

To update your Autocom CDP interface to Realise 3, 2010
- Hardware ID and key to install on PC
- Hardware ID and key to install on Pocket PC
- dump to ATtiny
- dump to 29F800

Pass in PM ):Please,pass,...thanks in advance.

[bonux]

Hi, for those who cannot connect bluetooth with passwords 0 or 0000 try 1234, this was my issue.

[flavyus1987]

Have anyone a solution to use Delphi software and Autocom software, both on the same hardware autocom?
I was looking on the forum but i don't find nothing about this.
The first and a hard step is because i don't have a source to download Delphi 2011.1.
If i wrote on the bad place please move my post on the corect thread.

[ishell]

Have anyone a solution to use Delphi software and Autocom software, both on the same hardware autocom?
I was looking on the forum but i don't find nothing about this.
The first and a hard step is because i don't have a source to download Delphi 2011.1.
If i wrote on the bad place please move my post on the corect thread.
I have installed and working delphi truck sw 3/2011
It is more stable than autocom for me.

[flavyus1987]

I have installed and working delphi truck sw 3/2011
It is more stable than autocom for me.

Please give me more detalis.
1st = where can ai activate 2011.3?
2nd = delphi 2011.3 working on autocom hardware only with firmware update from the software?
3rd =if i found delphi 2011.1 i can use directly on my autocom without make change to serial and firmware?just intalling it?

[ishell]

Please give me more detalis.
1st = where can ai activate 2011.3?

2nd = delphi 2011.3 working on autocom hardware only with firmware update from the software?

3rd =if i found delphi 2011.1 i can use directly on my autocom without make change to serial and firmware?just intalling it?
I can't test it.


1 offline with members helps
2 Sure need firmware update but it's no troubles teated some time
on my device .
3 I can't test it.

[flavyus1987]

If someone wants to help me with activation for delphi or autocom 2011.3 i will try if it works.I understood that delphi and autocom working with the same activating file.
I found delphi and autocom 2011.3, but i don't find delphi 2011.1.
I know i am not a veteran here, and i don't so much number of posts, but maybe in the future i'll be helpful with something.

[mdanilo]

What protocol uses this trucks to comunicate?

J1708

Rgds.,
Danilo

[flavyus1987]

Today i had read about version 2012.1.From where can we take it?

[vevepatronu]

share with us where you read that, till now i didn't had that information about a new release, i don't think it is alredy posted, we should wait a little more...

[flavyus1987]

Just asq our best friend GOOGLE and it answer you.
Maybe samebody will share for us and we will offer another service for it and activation.

[mattydr67]

No new version till now
The 2011.3 was the last
The new one will be realese in July-August this year (I suppose so )
For Delphi softwear you can try here
Delphi Europe Service Operations (http://europe.delphi-dso.com/)
Good luck


@flavyus1987 - do you know how to activate it?
I'm not intresting in this but I ask just for curiosity, Thanks

[michalez]

Here is information about newest update to autocom. So we must wait, coz they want to add new security for program.:beer:

[flavyus1987]

Yeah, 1xmounth more waiting.
Last night i readed this message from autocom.se.
Sorry, was my bad.

[kisslorand]

Anyone knows what is the role of the XC68HC58 MCU inside the Autocom interface?

[andy99]

Hello DK?s

How to update your Autocom CDP....

To update your Autocom CDP interface to Realise 3, 2010
- Hardware ID and key to install on PC
- Hardware ID and key to install on Pocket PC
- dump to ATtiny
- dump to 29F800

Pass in PM ):

hello need pass for dumps thanks

[Amine13]

HI,
Any idea about what Bluetooth module can be fitted inside PCB of Autocom, I have one which the bluetooth module seems to be damaged.
BR.

[flavyus1987]

Get out PCB from the case, and try after.I think you have not antenna conected to main-board(without conector)
If working like this, solder an antena to the BT module.

[Amine13]

Get out PCB from the case, and try after.I think you have not antenna conected to main-board(without conector)
If working like this, solder an antena to the BT module.
Thanks for your reply.
I have antenna and it was connected; the unit is recognized and even connected; but when the communication starts, then the unit is self disconnected, tested with other unit, and works fine..

[chrismoore02]

Thought i would give you an update, i have replaced the resistors R74 and R75 for 390ohm and now the unit can scan 2001 ford ka ok. :)

[meteor80]

Hello.
I have problem with autocom.
It communicate with Ford and other brands, but it don't communicate with Opel Astra H with airbags and central electronics.
It is SW CAN. Does someone know how to repair that?

[andy99]

Hello DK?s

How to update your Autocom CDP....

To update your Autocom CDP interface to Realise 3, 2010
- Hardware ID and key to install on PC
- Hardware ID and key to install on Pocket PC
- dump to ATtiny
- dump to 29F800

Pass in PM ):
Pass please

[DiagService]

HI guys I have problem with MB C-Class W202 1996 year 2.0 benzina I can not connect with AutoCom ECU, Airbag, SRS, ABS...
Have you any Idea fot this solution ???

[angelx431]

How to remove AUTOCOM 2011.1?

[djcristi]

uninstall and clean registry if you want to install 2011.3

[angelx431]

uninstall and clean registry if you want to install 2011.3 in detail
clean registry?

[djcristi]

clean autocom entrys from reg

[obd.tech]

more detail please?.......idiots guide for someone never done this before.
thanks

[Amine13]

Download ccleaner and run it, it will clean lot of unneeded registery keys.

[solar]

hello,
I have some problems with autocom:
was everything okey,but after i fail to connect to ford mondeo 2004,i see no LED lights on at all,device dead.
I have oki chip inside,was able to do everything on fords before,but now,not work on all cars...try to reinstall software no look,then i try to plug inn cable to usb i can see table(windows.xp)..unknown device...maybe someone have this problem with autocom?thanks.

[djcristi]

i think your hardware is dead, check the voltage regulator near the capacitors

[Amine13]

I got one time same fault, and guess what; Pin 4 or 5 (ground pins, don't remember which one ) was inclined inside OBD2 female blue connector of autocom, so no communication because simply no ground. made it straight, then all went fine;, just take plug, and see if all pins are straight.
Good luck!

[djcristi]

yes, you can also measure inside the autocom , if it get's power from obd

[solar]

I have power from car,but no power from pc usb.Normally then connect autocom to usb,pc recognize device and show Vci device conected,and autocom LED on(red,then not connected to car)....but my autocom complettle dead then i try connect to pc(no LED on)....ant pc shows Unknown device connected,so nothing working even then i try to connect to car,.....looks like no drivers for autocom,but when i try another autocom(good one) everything works,so for sure not software problem,something wrong with pcb board(top one with LEDs).

[Amine13]

Looks like the hw of your autocom is dead, for the price it costs, don't bother yourself to fix it, better get a new one !
Regards.

[djcristi]

I have power from car,but no power from pc usb.Normally then connect autocom to usb,pc recognize device and show Vci device conected,and autocom LED on(red,then not connected to car)....but my autocom complettle dead then i try connect to pc(no LED on)....ant pc shows Unknown device connected,so nothing working even then i try to connect to car,.....looks like no drivers for autocom,but when i try another autocom(good one) everything works,so for sure not software problem,something wrong with pcb board(top one with LEDs).

check the ft232 ic

[del635]

I'm impressed so far with mine, hasnt let me down on anything in the list from older voyager abs to newer ford airbag.....

[angelx431]

more detail please?.......idiots guide for someone never done this before.
thanks
idiots-???????

[BENDIMIA BOUSMAHA]

j'ai instalaler autocom 2011/3 ala fin de l'instalation il me demande l'activation du soft j'ai fait par usb j'ai u un fichier d'activation je ne s'est pas coment fait votre aide merci

[chrismoore02]

English ?

Sent from my Galaxy Nexus using Tapatalk 2

[mattydr67]

j'ai instalaler autocom 2011/3 ala fin de l'instalation il me demande l'activation du soft j'ai fait par usb j'ai u un fichier d'activation je ne s'est pas coment fait votre aide merci

Maybe someone will help you but try to speack English in this forum sir. This is the rule.
You can simply use the Google translator if you really need it.
Good luck

[obd.tech]

Anyone found a fix for BMW's not working yet?(E60/65/39/90)

Thanks OBD

[ovidiu1967]

also anyone know to reprog bluetooth from autocom or new one like bluetooth from autocom.
i try but unsuccesfuly , maybe pin for enter in AT mode isn't 34 or my schematic for UART is wrong.
somebody have experience with this or with bmw solution?
thanx!

[tk500]

I tried to put BT into AT mode - without success.
There seems to be a nonstandard firmware in BT module.

[baner]

I tried to put BT into AT mode - without success.
There seems to be a nonstandard firmware in BT module.

Just to confirm, I also tried put it into AT command mode, but seems that module is with nonstandard pinout.:stupido2:

Also without success.:giveup:

Regards and respect!:jiggin:

[tk500]

pin-out maybe is standard
removed working module, connected on my desk - work OK
just no AT mode

[djcristi]

why do you say bmw not working? do you have hardware with oki chip?

[chris_e36_328]

I have same issue woth BMWs. I have kit with the oki chip in, bit no comms woth new bimmers.. Drives me nuts..

[djcristi]

oh, i will try tonight on an e65 to see...

l.e. doesn't work on e65 2001 735i ....
don't know if it's hardware or software related cause it cannot talk to any module, even on this e65 all modules can talk on k-line, so don't need DCAN...

[titoun]

HY everybody,

Just a little question: Is anyone have an idea of the exact polyswitch reference on the map relays interface and above the holding current?? marking component P200 or F200?

Raychem or TYCO or littlefuse manufacturing.

2A (holding current)and 8V apparently ???? But it'is a low voltage for me ?????


Thanks by advance for your respond.

Regards.

Titoun

[kisslorand]

Anyone found a fix for BMW's not working yet?(E60/65/39/90)

Thanks OBD
There are some folks who found the problem but they won't share. I am trying to fix that for 2 months now but no success. I have a working and a non working interface, the main PCB is my problem. I exchanged components from the good interface to the bad interface (except the main MCU) but still haven't came to any solution.

[bax0904]

Dear colleagues my English is not the best but you will understand me, I have a copy autoc with version 2011.3, with regard to passenger program works perfectly, even there are things that can not be my multidiag, a freight program does what it has obd else because I did not even try no one has the right arrangement of pins, I asked if someone would have origuinalne load cables to make the seeds and sent, thanks in advance

[407ron]

I have tested autocom 2011.3 on alot of makes and models where it works fine..:cool:
But i plugged into a 2002 ford transit with 3 different autocoms (All with the OKI chip fitted) but none of them communicated with it...There is battery voltage on 16 pin obd port.
I have also tested these on a 2005 focus 1.6 tdci which had full coms with all ecu's....look like autocom does not like the older fords...:confused:
Rdgs Ron.

[zefoguete]

How to pair Autocom device over bluetooth, what is the pass key ?

On my autocom the pass for bluetooth is 0000(4 zero )
i think its the same for all

best regards

[djcristi]

no, there are many bluetooth pins for clones 1234 or 0 or 0000

[minchion]

Hi everyone !
I have a problem with bluetooth, already try on 2 pc but can't see it, so couldn't connect . Anyone with a working unit can verify if soldered pin on bluetooth module are correct ? Thanks !

[chrismoore02]

I can look tonight for you on my unit what issue are you having with the Bluetooth?

Sent from my Galaxy Nexus using Tapatalk 2

[minchion]

well it never worked, if you see the picture not all pins are soldered. I need if the soldered pins are the right or I have to solder them all.

[chrismoore02]

Ok I see on your picture now. I will look at my unit tonight

Sent from my Galaxy Nexus using Tapatalk 2

[djcristi]

mine looks like this and works perfect

[michalez]

so guys, there is a new version of deplhi/autocom

[tk500]

All Chinese are blacklisted ...

[michalez]

All Chinese are blacklisted ...
you are wrong, in other forum someone activated 30250

[makadam]

Anyone found a fix for BMW's not working yet?(E60/65/39/90)

Thanks OBD

Autocom work perfect on e39!

Send from Samsung Galaxy S2

[tk500]

you are wrong, in other forum someone activated 30250

yes c??, but solution is new ...

[djcristi]

doesn't matter if 30250 it's banned, you can change serial number in your clone

[michalez]

yes, but need to know hardware key

[minchion]

mine looks like this and works perfect

Thank you ! your pics look a little dark but same I see it's same connection, just another brand of module.

[titoun]

Hi everyone !
I have a problem with bluetooth, already try on 2 pc but can't see it, so couldn't connect . Anyone with a working unit can verify if soldered pin on bluetooth module are correct ? Thanks !

Hello

On the second photo, the transistor Q1 is missing .... to see !

@+

[Amine13]

HI,
After made update to 3 2011, Bluetooth won't to accept linking code, tried all codes possible, 0, 0000, 1234; 123456 ; and nothing works, Any idea?
With usb it works fine.

[minchion]

I can try with putting on the Q1 transistor but have seen other photos with Q1 missing and they say it's still working, don't know what to think :banghead:
made update to 2011_03 but in never works since I got it and was 2011_01.

[obd.tech]

Any ideas/updates on a solution for 2011.3 (with OKI) not working on BMW yet.......EOBD only working......the rest = no comm's

obd.tech

[baner]

I can try with putting on the Q1 transistor but have seen other photos with Q1 missing and they say it's still working, don't know what to think :banghead:
made update to 2011_03 but in never works since I got it and was 2011_01.

You should not even bothering to try it with that Q1 trans in place. That transistor is gate for green bluetooth LED indicator.
With that transistor in place green BT LED will be on just at real transfer via BT.:stupido2:

Otherwise, without that transistor, green BT LED :stupido2:will be always on until you use USB cable for connection, then it is going to red.

That transistor does not have any impact on communication with vehicles.:bike:

Regards and respect!:hello:

[djcristi]

i confirm baner (http://www.digital-kaos.co.uk/forums/members/115777-baner/)'s post about q1

[minchion]

Ok ! thank you baner & djcristi!

[HenrichSGU]

Hi,
can any one confirm if Delphi version 2012.1-2 work with Autocom CDP sn:30250 ?

[djcristi]

maybe, if you can generate proper hardware key & activation ;))

sn doesn't count , you can change it in 5minutes

[jjrp255630]

about work with volvo trucks, anyone have sucess?

[HenrichSGU]

maybe, if you can generate proper hardware key & activation ;))

sn doesn't count , you can change it in 5minutes


... sure, but how to get it (correct hw key + SN)...

[ucianuss]

how to change the series (39 071)
How can AUTOCOM Truck Pro CDP to work with CARS

[minchion]

how to change the series (39 071)
How can AUTOCOM Truck Pro CDP to work with CARS


You have to install Cars CDP Pro. I have installed both Cars & Truck 2011_03 with same serial 30250 and both working.

[fluorescent]

I buy recently a Autocom cdp 2011-3 version and until now all perfect it do it all the cars that i test it:
-renault espace 2004
-mercedez benz w203 2000
-audi a4 2000
-ford focus 2004 and 2000 including softcoding injectors in 2004 model
-peugeot 206
I have to mentioned that when i received my clone, i open it to see the quality and i dont be so happy with what i see, bad solders everywhere specialy in rele?s pins.
When i buy a clone always i do this procedures.
I open the clone ,get a good flux, take care with the flux smoke is not to good to expose your breathing to much in this products, and remake all soldures of the pcb.
Right now the clone works with every car that i test.
Dont use bluethoot is a crap, they put external antena but is only for estetic, is goot to know that when you have a usb stick bluethoot or wifi you have to disconect some condensers or resistence on this, to disconnect internal antena, and use that external antena conector provided.
In Autocom he use the internal antena of bluethoot , and inside of aluminium box, how you dont want to loose the signal?
Conclusion: if you want a good clone you have to resolder all components before test it in the car and use usb port.Cheers.

[ucianuss]

For your Cars CDP 2011.3 /Serial Number = 39071/ KEY DieselMax=?

[solar]

i have some problem with autocom 2011.1.
autocom not work anymore,i try to reinstall software,try on different laptops same result:
try to connect to car no communication,so i go to settings to do hardware setup and here then i try to look for com port(automatic or manual search),i see no communication+firmware not loaded and another table with***incorrect firmware version,please update your firmware***i try to do updates(connect to car wait around 5 min.) and all process was OK,but when try again to locate com port again same story...divers looks Ok,computer recognize autocom(vci device found),but something missing...............maybe,anyone have same problems?i check all connections,soldering, maybe problem in 29f800.......here my file of this chip....any ideas?

[HenrichSGU]

Hi,
first half of your file seems be damaged.
Try write this file. (i have this file from some topic in this forum)

[solar]

thanks,i try later,now football time:)

[baner]

they put external antena but is only for estetic, is goot to know that when you have a usb stick bluethoot or wifi you have to disconect some condensers or resistence on this, to disconnect internal antena, and use that external antena conector provided.
In Autocom he use the internal antena of bluethoot , and inside of aluminium box, how you dont want to loose the signal?
Conclusion: if you want a good clone you have to resolder all components before test it in the car and use usb port.Cheers.

If you dont mind, and if you have time, can you please be more specific for which components of bluetooth receiver must be removed to achive proper work of BT on autocom clone?:stupido2:

Regards and respect:hello:

[nany]

Hi mate , i ask question for someone have experience with Autocom How to do a diag for chevrolet optra ,note that it does not exist on the list and how to deactivate the message when opening soft (an update is available)
thx all for your contribution.

[autocargo]

Hi mate , i ask question for someone have experience with Autocom How to do a diag for chevrolet optra ,note that it does not exist on the list and how to deactivate the message when opening soft (an update is available)
thx all for your contribution.


It seems that is a Lacetti after all... Try Lacetti if there's not many modules in Autocom to diagnose, then try some Vauxhall/Opel models, as they share same engines/ equipment. To get rid of update message there is a small program called ''Run as date'' you should be able to find it here on forum. Regards.

[nany]

It seems that is a Lacetti after all... Try Lacetti if there's not many modules in Autocom to diagnose, then try some Vauxhall/Opel models, as they share same engines/ equipment. To get rid of update message there is a small program called ''Run as date'' you should be able to find it here on forum. Regards.

Hi mate , thx for ur reply and please can u share this program. i do the search in the forum but nothing !!! i appreciat if u can share or upload it here

[marro08]

I have autocom 2011.03 pro and i can?t install in my pc.
Anyone who knows?

[marro08]

can you send password?

[titoun]

Hello DK?s

How to update your Autocom CDP....

To update your Autocom CDP interface to Realise 3, 2010
- Hardware ID and key to install on PC
- Hardware ID and key to install on Pocket PC
- dump to ATtiny
- dump to 29F800

Pass in PM ):

Hello, please send me a pass ..... for dumps !

Best regards.

[Harrycz44]

Hello friends
today I got new cdp, I test on BMW car and work well, but Ford Mondeo diesel year 2003 can not find unit engine and immo. I look Inside and OKI chip is there..( OKI JAPAN ).Resistors R1148 (R74) and 1149 (R75) are no 3900 but 39R0....Know anybody solution for my problem pleas??

[djcristi]

it's a problem only with e60/65/90 ! not all bmw ! and oki chip is for ford....

[autocargo]

Hello friends
today I got new cdp, I test on BMW car and work well, but Ford Mondeo diesel year 2003 can not find unit engine and immo. I look Inside and OKI chip is there..( OKI JAPAN ).Resistors R1148 (R74) and 1149 (R75) are no 3900 but 39R0....Know anybody solution for my problem pleas??

You have to replace R74/R75. 39R0 equals 39 ohm. You need 390 ohm there. You can use axial ones,easier to find. SMD ones should be marked 391 or 3900 for the value of 390 ohm you need. Regards.

[Harrycz44]

And really help me when change this resistors? Becouse i testet MB bz k-line and work well, and only engine ford unit no..

[autocargo]

And really help me when change this resistors? Becouse i testet MB bz k-line and work well, and only engine ford unit no..

Yes it should help you. I had the same problem, no communication with older Fords tested on years 1999 up to 2003, and changed those resistors. After replacing resistors all was ok. Good luck. Let us know if worked for you as well.

[7788]

There are some folks who found the problem but they won't share. I am trying to fix that for 2 months now but no success. I have a working and a non working interface, the main PCB is my problem. I exchanged components from the good interface to the bad interface (except the main MCU) but still haven't came to any solution.
Hi!
One guy tell me that, he solve this problem:
"Found two foult on CDP so don't work on BMW E90 and E60 models.
One is poor qualty SI9241 K-line trancievers on main PCB.
The other is on rellay board. When CDP powered and connected to USB, run SW and connect to any car and then go back to main SW window. 3 rellays must be ON when in this window! If only 2 are ON BMW E60 and E90 don't work!"

[Harrycz44]

Yes it should help you. I had the same problem, no communication with older Fords tested on years 1999 up to 2003, and changed those resistors. After replacing resistors all was ok. Good luck. Let us know if worked for you as well.

Hello today I tried it and WORK! Thank you

[autocargo]

Hello today I tried it and WORK! Thank you


I'm glad it worked for you as well m8. :hello:

[ioanrokos]

Hi DK members.
I have a clone of AUTOCOM with software 2011.3
Since now i have check it in a lot of cars Audi, BMW, Mercedes
Ford, Fiat.
Yesterday when i plug in a BMW530d 2005 mod, is shown (vechile is not responding). at the ISS mode the same in all ECU of the car.
Only in generic OBD can access the primary ECU.
Please any advice.
Thank you.
My resistors are 3900 (390 ohm) .

[ioanrokos]

it's a problem only with e60/65/90 ! not all bmw ! and oki chip is for ford....

Hi! I have the same problems with BMW'S.
Any solution yet?
Thank you

[ALEXEI]

all users whish to know this

[ioanrokos]

if anybody know a solution pls sent me a pm
I am not a seller or provider.
I am a car mechanik in Greece and i want to do my work
Regards John.

[daewo97]

and I, have the same problems the BMW E60, E90, not connecting with this car .. but apparently not found, one solution

[ioanrokos]

and I, have the same problems the BMW E60, E90, not connecting with this car .. but apparently not found, one solution
Yes m8, somebody know the solution, but they wont share it
Clever boys...

[dreambike]

Hello, The forum You Seen That put him UNOS Components Fail to Autocom, I have ONE IS 2011.3 Relear and gives me this failure VCI Times Found, Has To Do With Components That given hay That Change? Components ESOs They themselves no different than what has or hay to put another type? Let me know what I have to DO. Thank you very much.

[solar]

Hello,Enyone try new version hardware autocom(from China,red one),maybe works better with bmw,ford???

[AUTOLITERO]

I to function by changing the resistance of 390 to 470
and luxury will

[ioanrokos]

I to function by changing the resistance of 390 to 470
and luxury will
Have you change resistors 390 ohm to 470ohm?

[eprommazza]

hello
my cdp work ok when connected also with bluetoot connected ok but after connected ..disconnected and receive error advise..(VCI NOT FOUND)

someone tell me why my cdp after connected I always get error vci not found ...
??
this with all car and with usb and bluetoot same problem!
my resistor are 390 ohm


thanks in advance

[AUTOLITERO]

the resistance is 390 a470 when not connected to ford

[eprommazza]

the resistance is 390 a470 when not connected to ford

yes this i have understand ....my problem no this is other..

[ioanrokos]

yes this i have understand ....my problem no this is other..

1. Disconnect from internet
2. Delete folder with all files in it: "c:\Documents and Settings\USER\Application Data\Autocom
3.Delete folder with all files in it: "c:\Documents and Settings\All Users\Application Data\Autocom
4. Start Main.exe, reactivate software and you're done!
5. Most important, stay off line from the internet.

[eprommazza]

1. Disconnect from internet
2. Delete folder with all files in it: "c:\Documents and Settings\USER\Application Data\Autocom
3.Delete folder with all files in it: "c:\Documents and Settings\All Users\Application Data\Autocom
4. Start Main.exe, reactivate software and you're done!
5. Most important, stay off line from the internet.

work perfect now thanks
you think need work forever without internet connection? or only this cases?
i check need use forever without internet connection ..
otherwise the problem returns!!!

[willobd]

hello
do you have 1.2011 software?
best regards
i have both 2011.01 and 2011.03 version software.
what's your hardware version??
( no addys :rulez: )

[willobd]

work perfect now thanks
you think need work forever without internet connection? or only this cases?
i check need use forever without internet connection ..
otherwise the problem returns!!!

The solution is (delete the software then install and active again):

1- Uninstall the software
2- Delete the license (search folder name autocom in windows. and delete all folders)
3- Setup software. And make activation


The steps for not detect VCI:

1. Disconnect from internet
2. Delete folder with all files in it: "c:\Documents and Settings\USER\Application Data\Autocom
3. Delete folder with all files in it: "c:\Documents and Settings\All Users\Application Data\Autocom
4. Start Main.exe, reactivate software and you're done!
5. Most important, stay off line from the internet.

[ioanrokos]

work perfect now thanks
you think need work forever without internet connection? or only this cases?
i check need use forever without internet connection ..
otherwise the problem returns!!!
yoy need block Main.exe access internet.
yoy may modify registry or use an antivirus to block main.exe

[ral.t]

Can someone tell me this is worth buying? Thanks...
Best Quality Autocom CDP+ Quality A for Cars / Trucks and OBD2 | eBay (http://www.ebay.com/itm/Best-Quality-Autocom-CDP-Quality-A-for-Cars-Trucks-and-OBD2-/110912850577?pt=Motors_Automotive_Tools&hash=item19d2ebca91&vxp=mtr)

[ioanrokos]

Can someone tell me this is worth buying? Thanks...
Best Quality Autocom CDP+ Quality A for Cars / Trucks and OBD2 | eBay (http://www.ebay.com/itm/Best-Quality-Autocom-CDP-Quality-A-for-Cars-Trucks-and-OBD2-/110912850577?pt=Motors_Automotive_Tools&hash=item19d2ebca91&vxp=mtr)

As it seems has not bluetooth.

[Meat-Head]

so which bmw problems with?

[ral.t]

I wanted to buy it but I do not know Is ok..

[ioanrokos]

Ask seller first if he test it.
And then you need luck.

[mattydr67]

Ask seller first if he test it.
And then you need luck.

Mate Chinese seller don't have European cars or American to test.
Second they are seller, most of them are students which do this for extra money.
They have maybe two offices on square metters.
It is simply to sell tools if you are in China, you don't need to invest anything.
Look how it works:
They share some pics on their webshops, then when you decide to buy you'll send the money by paypal or whatever, then with your money they buy the tool from factory, n no no, from other resellers, and after the courier deliver the package they change the adress with yours and contact another courier and send you the package.
Do you any TEST in this "tree"
Come on you must to have luck or to spend time waiting other fullish guys to buy one product or other and show their experience with the tool you want to buy.
And from this thread to you think that Autocom clones are a very good tool?
Think about
Good luck

[Harrycz44]

1. Disconnect from internet
2. Delete folder with all files in it: "c:\Documents and Settings\USER\Application Data\Autocom
3.Delete folder with all files in it: "c:\Documents and Settings\All Users\Application Data\Autocom
4. Start Main.exe, reactivate software and you're done!
5. Most important, stay off line from the internet.

Hello friends of DK
?
I have same problem but only with s/n 30250, s/n 30847 work without problem.. Know anybody how change serial number??

[ioanrokos]

look here
http://www.digital-kaos.co.uk/forums/f155/autocom-cdp-177633/

[mick711]

You can find in digital kaos a lot of tools for that .

Like RealTerm ;)

[Harrycz44]

You can find in digital kaos a lot of tools for that .

Like RealTerm ;)

I find it.. thanks
Now I tested bmw 530 Diesel E39 530D DDE 4.0 and can not find Ecu engine.. all another ecu yes.

[mick711]

You probably have a bad relay who are always on and KKL don't work . But you can verify resistor R74 R75 390 Ohm

[Artilect]

Hello friends of DK
?
I have same problem but only with s/n 30250, s/n 30847 work without problem.. Know anybody how change serial number??


Look hire: http://www.digital-kaos.co.uk/forums/f155/help-change-serial-autocom-please-279643/#post1620218

No need to solder and flash, the tool doit by USB. ;)

BR

[Harrycz44]

You probably have a bad relay who are always on and KKL don't work . But you can verify resistor R74 R75 390 Ohm

Maybe is problem in car, becouse another bmw with DDE 4.0 work

[Meat-Head]

I find it.. thanks
Now I tested bmw 530 Diesel E39 530D DDE 4.0 and can not find Ecu engine.. all another ecu yes

Maybe is problem in car, becouse another bmw with DDE 4.0 work

Eye we had a chap in the other week, bmw 3 serioes 1.9 petrol, looking like 3 dud ecu's 4th worked.

[flavyus1987]

BMW with DDE5 workted on mine.Problem on old ford.But it's not a problem, i don't like fords :D

[ioanrokos]

BMW with DDE5 workted on mine.Problem on old ford.But it's not a problem, i don't like fords :D

Did you try to change resistors?

[flavyus1987]

No, i don't change anything.The rezistor on mine PCB is 30 ohm.
I tested on manycars and worked ok: opel like corsa.astra from 2000-2007,fords 2006,alta 156,golf3, polo '97,MB c220 2002, mb A class,toyota FJ = hummer , renault espace/megane,bmw 320 from 2005 with dde5, etc...
Only problems on old ford.I waiting to test on bmw series 5 and 7.
A friend of mine have autocom with 390 ohm rezistors, but his working on ford and not working on BMW DDE5, mercedes C220 from 1998 and others.

[ioanrokos]

have you test it on BMW E60?

[flavyus1987]

No, i waiting to catch one to test it.If working, i'll never change the rezistors, if not i'll change that rezistors.

[viki300]

Hello all after succesfully install of 2011.3 software i try to flash firmware i just hook it up to obd adapter and plug 12volts to it and start flash and far beyond half way it stop and start complaint that voltage wrong or com port wrong or usb cable not connect and if i try again it start flash and stops right away with same story voltage wrong ... should i try to connect to car and try again or is going to gone autocom

[mick711]

You plug 12 Volt with Battery ?
With a clone i think Autocom don't send to you new for free :D
Buy a new clone or find all files needed and unplug some chip and flash with programmer .

[autocargo]

Hello all after succesfully install of 2011.3 software i try to flash firmware i just hook it up to obd adapter and plug 12volts to it and start flash and far beyond half way it stop and start complaint that voltage wrong or com port wrong or usb cable not connect and if i try again it start flash and stops right away with same story voltage wrong ... should i try to connect to car and try again or is going to gone autocom

Install old version 2011.1 and flash back old firmware... it should work. Maybe your autocom version can't be upgraded to 2011.3...not all of them can...

[viki300]

ok i can try that thanks a lot

[flavyus1987]

Try to start engine to have stable 12V.

[autocargo]

ok i can try that thanks a lot

...and tell us if worked alright :bounce:

[viki300]

Hi and ok i connect autocom to car and flashed 2011.3 firmware and everything works now ok i didnt try that old firmware cos new worked ok

[mick711]

Hi and ok i connect autocom to car and flashed 2011.3 firmware and everything works now ok i didnt try that old firmware cos new worked ok

So you don't have 12 volt when you try first time .

[meteor80]

Does someone have solution for repair unit that doesn't connect with airbags in Opel Astra H?
All brands works fine but not astra H.

[viki300]

So you don't have 12 volt when you try first time .
Yes infact i did have 14.00 V but i think problem was that not in correct pin i did use adapter for bench flashing i quess it need other pins 12v than the normal ones:stupid:

[aliedvin]

Hello i have a problem "VCI not found". What is this?. What can i do?

[olmar]

Hello i have a problem "VCI not found". What is this?. What can i do?

Uninstall and delete folder.
Reinstall without internet connection.
Program run without Internet connection.
Block a program in Windows 7 Firewall (http://www.trishtech.com/win7/block_a_program_in_windows_firewall.php)

[aliedvin]

how i can delele the program complete? When I delete the program and install again it keeps something from the program, because the I don't need the key anymore and remembers the last type of car, model, engine.....

[paro44]

how i can delele the program complete? When I delete the program and install again it keeps something from the program, because the I don't need the key anymore and remembers the last type of car, model, engine.....

Delete the folder and clean the registry from autocom-entries.

[admiralx]

Delete the folder and clean the registry from autocom-entries.:beerglass::beerglass::beerglass:

[tiguan]

Uninstall and delete folder.
Reinstall without internet connection.
Program run without Internet connection.
Block a program in Windows 7 Firewall (http://www.trishtech.com/win7/block_a_program_in_windows_firewall.php)


I have the same problem "VCI not found".
I deleted these files

?c:\Documents and Settings\USER\Application Data\Autocom ?
?c:\Documents and Settings\All Users\Application Data\Autocom?

where can I find the folder for Windows Autocom license for delete ... please help

[olmar]

I have the same problem "VCI not found".
I deleted these files

?c:\Documents and Settings\USER\Application Data\Autocom ?
?c:\Documents and Settings\All Users\Application Data\Autocom?

where can I find the folder for Windows Autocom license for delete ... please help

Go to license and click dezactivate license or upgrade license
"VCI not found" appears if the Internet is active when the installation.Not run the program with active internet.

[tiguan]

Go to license and click dezactivate license or upgrade license
"VCI not found" appears if the Internet is active when the installation.Not run the program with active internet.


I always activate installed without Internet
but still keeps giving that error "VCI not found"

tomorrow new install and see if it goes well ...I hope

Thank you
Tiguan

[vwpd130]

I have the same issue. Have deleted the folders, uninstalled it, no internet connection and still get the error??

makes a good program a pain in the ass to use.....

how can i clear the registry of all autocom files etc.....ive uninstalled the program but the licence is still in there somewhere

can somebody post a "how to" regarding complete de-installation of program and clean up the registry?

win7 & xp

[m_toy]

Try to use Smarty uninstaller pro.

[Artilect]

If you have " VCI not found" error. You have after you have make the internet connection during the Autocom software is active you will have to change the serial number from VCI. You can make it via USB vith this Tool:

http://www.digital-kaos.co.uk/forums/f155/help-change-serial-autocom-please-279643/#post1620218

Then you will have to make the fresh instalation of the software while you are offline and make new activation vith new serial number.

BR

[Artilect]

First of all you have to check if FTDI is instaled properly.

Check this under Device Manager, and check if your VCI is recognized. If is not you have to reprogram FTDI vith MProg. But it should alvays work via Bluethooth.

[m_toy]

If you have " VCI not found" error. You have after you have make the internet connection during the Autocom software is active you will have to change the serial number from VCI. You can make it via USB vith this Tool:

http://www.digital-kaos.co.uk/forums/f155/help-change-serial-autocom-please-279643/#post1620218

Then you will have to make the fresh instalation of the software while you are offline and make new activation vith new serial number.

BR

Not necessary.

Just remove software using Smarty Uninstaller Pro, then manualy find and remove in register ( regedit ) all records contains "Autocom" ( some of them cannot be removed - it's OK ), then delete directories contain Autocom in Doc. and Set. and then install again without internet connection.

This help me, i had the same problem with VCI not found during comunication with controllers.

Regards

[Artilect]

Thanks, good to know.
I will try this next time.

BR

[vwpd130]

Try to use Smarty uninstaller pro.


many thanks, i totally uninstalled using smarty, then deleted the registry

re-installed and now its perfect

thank you

[mishu_b]

...
Please, I need security and configuration bytes !!!

KR

[ral.t]

I bought autocom CDP-pro 2011.03 Chinese clone. I tested it on the Opel Corsa C 2009 didn't communicate with any module. Ford Mondeo 1.8 TDI does not have ABS, airbags, ECU is poor. The Opel Vectra 1.6 1999 no abs. It is a waste of money..

[m_toy]

Fiat Brava '98, 1,8 16V, Hitachi MFi doesn't communicate, also ABS doesn't communicate. Only ABG can be connected, but in Marea directory. Brava doesn't contain "allied signal" ABG ecu.

[Meat-Head]

1998 brava thars 3 pin plug, you got power on it the autocom!

rumor has it orginal is instant talking

try fiat ecu scan

[m_toy]

1998 brava thars 3 pin plug, you got power on it the autocom!

rumor has it orginal is instant talking

try fiat ecu scan


That's clear for me ! It's been powered. All ECU's accessed by FiatEcuScan after.

[mishu_b]

...
open the case - find the "famous" 2 = 39 Ohm resistors and change with other 2 =390 ohms

than you will see that the tool will work also on opel!

KR

[ral.t]

But my interface looks different

Looks like this inside Good Quality Autocom CDP+ quality B for Cars / Trucks and OBD2 (http://www.ecutool.com/Good-Quality-Autocom-CDP-Quality-B-for-Cars--Trucks-and-OBD2_9921.html)

[mick711]

I bought autocom CDP-pro 2011.03 Chinese clone. I tested it on the Opel Corsa C 2009 didn't communicate with any module. Ford Mondeo 1.8 TDI does not have ABS, airbags, ECU is poor. The Opel Vectra 1.6 1999 no abs. It is a waste of money..

Waste of money , you joke ^^ you buy your CDP 2800? ?

With life time waranty ?

Or clone no garanty but need some modification sometime to work ?

But i'm agree for old car before 2000 lot is not suported .

[ral.t]

This is a clone which cost 180$ from eBay.I hoped that my clone would work without modification, but do not. Can it be modified to work? I am looking for 39 Ohm resistors but I did not find.Inside looks different..

[mishu_b]

...
upload here high quality pictures than I will guide you to find them.

kr

[ral.t]

http://www.digital-kaos.co.uk/forums/attachment.php?attachmentid=135555&stc=1&d=1312491594

http://www.digital-kaos.co.uk/forums/attachment.php?attachmentid=135556&stc=1&d=1312491594

Sory can not take photos better.

[Amine13]

This is new HW one, NEW for clones, means lot of problems, bugs; problems, bad surprises; so the classic one is working fine so far, except some known problems with BMW and Ford, so Don't see the reason why to buy such risky things, But I believe estethecally is better than the old one :D !!!!
Best Regards.

[ral.t]

Nicely... :s: Can someone give me help to make it work? Or is it really threw money

[chrismoore02]

I'm sure more people will be buying this version soon and then we will work out fixes for the bugs by testing and helping each other.

[mishu_b]

Sory can not take photos better.

hints for taking photos with high quality.

- first - avoid flash - it means take pictures in natural light
- use camera with high quality of the "sensitivity" - of possible DSLR.

than we can have a look on the pictures!

kr

[angelx431]

Help schematics adapter renault trucks 12 pin!

[m_toy]

...
open the case - find the "famous" 2 = 39 Ohm resistors and change with other 2 =390 ohms

than you will see that the tool will work also on opel!

KR


Checked them today, booth are ok.

[ral.t]

Here they are hope to be ok now..

http://www.digital-kaos.co.uk/forums/attachment.php?attachmentid=135874&stc=1&d=1312654718

[/IMG]http://www.digital-kaos.co.uk/forums/attachment.php?attachmentid=135875&stc=1&d=1312654718[/IMG]

[apv]

Hello, I have one like yours bought on ebay and I noticed that the pcb is not exactly equal to that of the gray interface. You can check the link you have posted comparing both, you'll notice that in ours we have a speaker and gray if any. Two white components are missing from the red interface and most importantly I think, is that which holds the card missing resistors and I think therefore there is no continuity in the tracks of the PCB and therefore the option does not work recorded in real time while driving. Perhaps an expert in the art to help in this regard. Greetings.

[ioanrokos]

Hi all.
I have made firmware upgrade to the interface from 1250 to 1130, i shouldnt have done this?

[mick711]

Hi all.
I have made firmware upgrade to the interface from 1250 to 1130, i shouldnt have done this?

You can install any firmware because when you change software version it say if it's the good or not firmware and if it's not the good the software install the required firmware .

You can jump i dont know but 1030 1170 1001 1389 no problem the firmware can be downgraded or upgraded .

[ral.t]

Does anyone have any advice for my interface?

[Amine13]

Does anyone have any advice for my interface?
Send back to your seller; and ask him either Refund, or send you classic Interface for Autocom.

[ioanrokos]

Hi, i try to connect to Ford Focus 1.6 98-04.
Only ABS & Multifunction responsed, the others ECU not responded.
I noticed resistors R75 R74 are marked as 390. what ohm are they?

Focus 06 connect OK.

[paro44]

Hi, i try to connect to Ford Focus 1.6 98-04.
Only ABS & Multifunction responsed, the others ECU not responded.
I noticed resistors R75 R74 are marked as 390. what ohm are they?

Focus 06 connect OK.

390 could be only 39 ohm. Use multimeter to verify and replace with 390 ohm resistors..

[ioanrokos]

OK i repace both and post results here.
Thanks.
I as saw in goodle they are 39 ohm.

[autocargo]

OK i repace both and post results here.
Thanks.
I as saw in goodle they are 39 ohm.

You need to replace those m8... I had the same problem and that was the solution.
Regards.

[ioanrokos]

You need to replace those m8... I had the same problem and that was the solution.
Regards.
I found only 270 & 470 ohm resistors, which of them can i use?

Have anybody tried this version?
http://autocom.se/en/products (2011.3 update_5)

[autocargo]

I found only 270 & 470 ohm resistors, which of them can i use?

Have anybody tried this version?
Products - Autocom (http://autocom.se/en/products) (2011.3 update_5)
Note sure m8.... Just solder axial ones (390 ohm) instead smd, there are easier to find.

[minchion]

Have anybody tried this version?
Products - Autocom (http://autocom.se/en/products) (2011.3 update_5)

I have made update and all ok after ( no need activation again )

[ioanrokos]

I have made update and all ok after ( no need activation again )
Do you know what extra models suport m8?

[minchion]

Well I thought maybe it resolves communication problem on iveco daily as I need at work( can't connect to Immo and Airbag ) but it doesnt, really don't know if new models were added, anyway tested on MB 220 Cdi, Kia Rio 1.5 dci, Fiat Scudo 2.0 Mjet etc. and all ok !

[ioanrokos]

Well I thought maybe it resolves communication problem on iveco daily as I need at work( can't connect to Immo and Airbag ) but it doesnt, really don't know if new models were added, anyway tested on MB 220 Cdi, Kia Rio 1.5 dci, Fiat Scudo 2.0 Mjet etc. and all ok !

Check reisistors R58, R74 & R75.
Should be 9R1, 391 & 391 (3900 & 3900) marked.

[minchion]

Check reisistors R58, R74 & R75.
Should be 9R1, 391 & 391 (3900 & 3900) marked.

I have the 2011.01 version VCI but cant find R58, R74 & R 75 should be these on the photo

[ioanrokos]

R74 & R75 is R1148 & R1149, should be 391 or 3900
R58 is at the other side otherwise R1008 should be 9R1

[minchion]

Yes I find it, it's a bit hard to see but is marked 9R1 so it's OK

[athlonxp]

R74 & R75 is R1148 & R1149, should be 391 or 3900
R58 is at the other side otherwise R1008 should be 9R1
My autocom has R74 R75 390ohm and R58 9R1 but do not work with e60

[ioanrokos]

Check this
http://www.digital-kaos.co.uk/forums/attachments/f166/135647d1344168101-autocom-can-not-connect-bmw-e60-61-e90-series-repair-autocom-cdp-vci.pdf

[ioanrokos]

Yes I find it, it's a bit hard to see but is marked 9R1 so it's OK
Chek the other 2 resistors, is 390 ohm?

[minchion]

yes the also seems good , both are marked 3900

[ioanrokos]

Well, we should not exept too much. is just a clone.
Too good for the money we spend to buy it.
Don't you think? Good night m8s

[Chokito5]

I use an Autocom trucks, and cars, but when I installed the 2011.03.5 version on my Lenovo S10 netbook, i can't use it. When I try to setup the COM port, or I try to connect to the cars or trucks, I get the attached error.
I tried the tools on other computer with same software, they work perfect.
I tried to use my Lenovo S10 with the old (2011.01) software, they work perfect.
What is this notice? How can I repair my computer?
I tried to uninstall, and clear the registry, but I can't delete some entry.

[ioanrokos]

I use an Autocom trucks, and cars, but when I installed the 2011.03.5 version on my Lenovo S10 netbook, i can't use it. When I try to setup the COM port, or I try to connect to the cars or trucks, I get the attached error.
I tried the tools on other computer with same software, they work perfect.
I tried to use my Lenovo S10 with the old (2011.01) software, they work perfect.
What is this notice? How can I repair my computer?
I tried to uninstall, and clear the registry, but I can't delete some entry.
Unistall and run ccleaner.

[mick711]

Failed to load FT_Reload.

Problem with FTDI driver you can try to uninstall drivers . Or like say ioanrokos .