Peugeot 307 ecu loked

[P2XA]

this post here:http://www.digital-kaos.co.uk/forums/f175/peugeot-307-1-4hdi-edc16c3-loked-ecu-208570/

[P2XA]

I very need our help.
Please!!!!!!!!!!!!!!!

[grinovsky]

programme flash in boot mode

[P2XA]

We could talk about flashing in bootmode?

[grinovsky]

yes.......

[P2XA]

I have to reflash the old ECU about two times on this machine and no problems.

[P2XA]

I use Galletto 1260 and all was allright.

[P2XA]

Tell me please about flashing in bootmode in this car!

[grinovsky]

so where is the probleme?

[P2XA]

New ecu loked after reflash

[grinovsky]

to verify your ecu you have to read flash and eprom by bdm port to sure that the 2 chips communicate with processore without probleme

[grinovsky]

did you speak french?

[P2XA]

And then what could be the problem?

[P2XA]

No! i don't speak in french.

[P2XA]

I hav't BDM programmer but i have X-prog M 5.0

[grinovsky]

New ecu loked after reflash
this happen many times when flashing with galleto
so to unlock the ecu you have to flash it in boot mode with galleto
check the connections(+12v and gnd) by schematics and by testing in plug ecu in car and connect ecu to galetto on table
and power ecu and flash ecu and it will be unlocked

[P2XA]

I have PPS 2000 and go to injection=>measure parameters=>and all parameter's are:????

[grinovsky]

so you have to recode injectors

[P2XA]

You know the pinout Galletto and EDC16c3

[grinovsky]

what is the car 1.6 or 1.4 hdi and what is engine code

[P2XA]

engine is 8HZ 1.4hdi 8valve 68cv

[P2XA]

injection is edc16c3

[rappttor]

if it is an edc16 and you dont have bdm, you can still use xprog to put the dumps back...
you can find on this forum how shuld be done.
you cannot speak about boot mode with edc16.
for the future, if you are plannig to mess arround with ecus software, just buy the propre tools, clone or not !
although galleto is a good tool, its not enough, and now i think you can see that.

[grinovsky]

p2xa how did you know that the ecu is lockek?

[P2XA]

What is the best tool you can recommend?

[P2XA]

I connected diagnostic PPS entering in BSI=>measure parameters=>immobilizer=> ecu is blocked and keys are synchronized.

[grinovsky]

ok,so use xprogm as rappttor (http://www.digital-kaos.co.uk/forums/members/148360-rappttor/) sayed to flash ecu

[P2XA]

It turns out that EDC16 be reprogrammed in bootmode?

[grinovsky]

yes,by your xprogm

[P2XA]

I understand that I need to reprogram the Flash memory 29BL802CB

[grinovsky]

yeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeessssssssss sssss

[P2XA]

Okkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkk kkkkkkkk kkkkkk
thanks

[P2XA]

I think the ECU don't work because software reference betweem old ecu and new are different.

[P2XA]

I flash the flash in-circuit using the X-Prog, the process went without error but the ECU is still blocked.

[P2XA]

I think that probably need to flash EEPROM MCP555 dump from the block which was taken by flash and then everything should be OK.

[rappttor]

still tormenting this poor ecu?!?

[P2XA]

Yes! will torment to the finish

[P2XA]

Need eeprom MCP555 and flash with work ECU edc16c3

[P2XA]

The essence of the problem is that there is another car Peugeot 307 1.4Hdi 68cm 2003 who had a problem with the ECU - this unit has been replaced by almost the same (on the new number does not match the refernce SW) machine does not develop bolle 3000 RPM burns check enjine (diagnosis reads the following error: An internal error and the wrong ECU codes nozzles). I am sure that it is absolutely the same block, we have not find a Problem for not matching SW version.

[P2XA]

I'm aware of those actions that need to be done. At first I reflash Immo machine but was got issued immediately antipollution fault and error diagnosis deducted the following items: an internal error and the wrong ECU codes nozzles. Then I thought eeprom MPC555 processor and request a new ECU (after the record is written for the test - write was successful). After these actions diagnostics ceased contact with 2 ECU (old and new).

[P2XA]

Wiring diagram X-prog-M to the ECU edc16c3 this:
http://www.digital-kaos.co.uk/forums/attachments/f155/58205d1302535094-edc16c3-xprog-m-x-prog_mpc_info.jpg

[grinovsky]

if you read mpc555 with xprogm the result will be :no communication with ecu
the only way to read write mpc555 with succes is to use bdm100

[P2XA]

I am wondering if he could not die an old ECU after reading eeprom MPC555 programmer X-prog-M 5.0?

[P2XA]

If yes then where to look for a dump MPC555?

[grinovsky]

try to flash mpc by bdm100

[paraver]

if you read mpc555 with xprogm the result will be :no communication with ecu
the only way to read write mpc555 with succes is to use bdm100


After this happen what can be done to restore it?

Regards

[grinovsky]

flash mpc dump by bdm100 will solve the probleme

[TRISIEN]

HOW TO READ AM29BL802CB PEUGEOT AND CITROEN ECU BOSCH X PROG M WITH THANKS

[xtreem]

flash ecu witch Bdm100, witch mpc and flash and eprom software.
use backup witch the same sw and hw...
it will work again