Corolla 89170-02240 crash clear needed

[KACZANUK]

i need help clearing this crash data plz help

[credoline]

erase 00 00 28 E5

[ChipGods]

put FF's in lines 0100h and 01D0h

[KACZANUK]

erase 00 00 28 E5


put FF's in lines 0100h and 01D0h

Thanks friends.
But I'm confused! :hmmmm:
Should I just erase 00 00 28 E5 or up to 100 lines 1D0?
Or both?
Thanks

[ChipGods]

Thanks friends.
But I'm confused! :hmmmm:
Should I just erase 00 00 28 E5 or up to 100 lines 1D0?
Or both?
Thanks

first try one of the variant, then second.
if not work - both :)

[HONDA C]

i need help clearing this crash data plz help


try this and report

[KACZANUK]

i need help clearing this crash data plz help


try this and report


friend, I think he cheated.
This is the same file I posted ...

[AMLGAR]

try.good luck:bebored:

[HONDA C]

friend, I think he cheated.
This is the same file I posted ...


hi i am sorry i made a mistake when upload it

the right is this i am sorry again friend

[KACZANUK]

try.good luck:bebored:

It worked perfectly !!! :top:

Thank you all for your help!

[churry]

erase 00 00 28 E5

hello. credoline and chipgoods. I'm with airbag units and motor unit ecu-immobilizers etc. Although I already few and well. what really interests me is knowing how to program for in-line programming function that changes to leave the unit clean and functioning. Now I do it with programs like tachosoft, airbag crash data or requesting files in this forum but did not control the code change and it signifies. already know pogramacion involved but can you tell me where to start changing channels hex editors and translators of code. informatico-mail and I want to start. I scheduled something, etc. and I think I can learn gradually. if you need anything with it.



I also ask a problem with the upa-usb programmer and airbag unit.

the case with other developers as willen g4x or x-prog without problems but the upa-usb can not get good reports I read and write NOR.

DO the steps are:

1-identify the chip to reset according to the reference unit
2-look at the controller chip that supports

3 - start reading the EPROM, EEPROM, flash etc.

all I know right.

although there are sometimes that is difficult to locate the memory to reset the unit, because it comes with other reference and it's hard, but good locations with the chip or pin number etc.

4-I read the chip clip unwelding programmer or reading the file

5-write the new file, and test the chip salary. well


QUESTION:
How to find the ID of the chip as a function of the reference unit and brand of car, where do you get that information?. I bag a few listings that are online, but the problem is that chip reference does not match the number of chip airbag unit. How do you know what specifically?

and the problem with the programmer is HAVE upa-usb clone (Chinese).

For example, with the airbag unit:
opel tigra TEMIC reference 93162255.
according to the lists that tells me is a memory type mc68hc08AZ32.

Well then go to the help document upa-usb programmer says that chip has 25 pins per side, look at the airbag unit and the chip is not the same reference.
Chip also brings 16-pin unit and it is clear that does not match and therefore you stay and say now that ... ... you can not go?


Another case
airbag unit
Reference alfa romeo 156 60665492
The chip according to the listed reset the HC08AS20.
look in the airbag unit and do not appear with these references, and good the only thing left is to check the pins match the pdf of upa-usb programmer say OK.
you connect and bridges as the documentation says the programmer, but fails to read the memory or is done reading but can not verify.

some help with this programmer.

thank you very much

I feel the extension of the message.

[credoline]

Motorola MCU-s have in third line maskset, that maskset tell you which chip exactly is it.
But that kind of support by mine opinion you have to get from hardware producer.

[autotechbr]

try.good luck:bebored:

Please send me password

Thanks

[datapage]

file .zip please clear

[Gintas]

hi,

cleared file
pass in pm

br
gintas

[credoline]

file .zip please clear

Cleared, pass in PM

[datapage]

Gintas : error modulo controle
credoline: I will test today, outside car workshop
corolla air bag trw 89170-02240 210902012 soic 8 25040

I tested some modiica?oes even probable error dump original bad,

[Gintas]

check wires on front or side impact sensors, if swap wires have internal fault dtc
erase dtc

[datapage]

modulo bad.
Ecu used again resolved.

[busnardo]

Please password ... Thank you!

[Diogo Mello]

[QUOTE = AMLGAR; 1115553] try.good luck :bebored:[/ QUOTE]
? poss?vel passar a senha?

[cleiwil]

Pass Please for test in my file! Very very thank's.

[trevormaharaj]

hi can anyone please clear crash
89170-02240
95040 eeprom
thanks in advance