etl clone issue and help

[tellfaia]

Hi to all, i?ve recently bought etl clone hc908, and now i have a 0j66d to read, i?ve soldered it and i get no echo from mcu error, and i i select 1L52H it stalls and it doesnt read at all
i have version 2.6 am i doing anything wrong should i do anything else?

Thanxs in advance

[RMCtech]

No idea my friend, I have a clone etl 908 that i bought 3 years ago and work fine, but I know that many late clones don't work, did you tested programmer with other CPU ?

[Brat]

clone hc908 is sh*t,buy original from etl.

[Zmann]

Hi to all, i?ve recently bought etl clone hc908, and now i have a 0j66d to read, i?ve soldered it and i get no echo from mcu error, and i i select 1L52H it stalls and it doesnt read at all
i have version 2.6 am i doing anything wrong should i do anything else?

Thanxs in advance

Did you mean SW version 2.6, sorry never try. Try again with v2.8

[obdmaster]

I have clone etl908 had problems with it, re solder full board then try again.

Mine works great now

[adam28]

I also have clone and works fine.

Also make sure you have pin 1 of mcu correctly aligned with pin 1 of board. I had friend who soldered mcu wrong way round.

Regards

P.S OBD did you sh!t the bed this morning early bird lol

[tellfaia]

LOL, it seems we are all early birds here lol, i?ve checked pin 1 but ill try to resolder board as obd sugested:) and will give feedback later, also about the firmware version is it possible to update it?

[tellfaia]

and its done:) lol, thanxs OBDMASTER

[tellfaia]

although i only get FFFFFFFFFFFFFFFF :(

[RMCtech]

What soft and firmware version you use ?

My clone work very nice with Soft v2.8 and Firmware v2.6 and its a rock solid programmer, it read everything I put on it, even it was able to read eeprom and flash of some real dead and not working 2J74Y cpu
Time ago I tested almost all mask supported and I was able of read every 908 CPU

[tellfaia]

all sorted now, its working like a charm, i?ve tested also a few others i have and it reads all:)
just perfect:) o i supose clones are not that s***ty at all:)

[nckryder]

I have also an issue with a hc908 Etl clone. It updates firware fine and all appears fine LED's work as they should as lited in help. But go to read it says programmer not found any one had this issue? I have resoldered the whole board but no read?. I would buy lots Etl programmers if they were easier to deal with

[tellfaia]

have you tryed to change speed in por options?

[obdmaster]

I have also an issue with a hc908 Etl clone. It updates firware fine and all appears fine LED's work as they should as lited in help. But go to read it says programmer not found any one had this issue? I have resoldered the whole board but no read?. I would buy lots Etl programmers if they were easier to deal with


To be honest m8, the original arent that expensive
http://www.etlweb.com/

email them for prices, you will have pleasant suprise.

[tas_daz]

from where you buy the programmer and from where company works and from where they didn t work?told that to save people to buy from not good company.i order from carsung and the seller told me that is 50% work ok but i order it and a xprog m.waiting to come in few days and see it .thanks

[Joe019]

I have buy ETL Original, and price is really good. Around 150***8364; HC908 programmer. Its original, it has support, and has a good quality.

BR!