renaulte 1.5 dci immo off

[kitioni]

please help with dumps immo off renault clio2 1.5 dci
ecu Delphi hom8200129063
eeprom 25080nc

[mihai_vyt]

can`t deactivate immo without emu.will start only first time after writting new dump

[kitioni]

i have emu.bat not have dumps

[mihai_vyt]

your dump virgin

[mihai_vyt]

.............

[kitioni]

thanks i try

[djamelEZS]

read your dump files 25080 put first line fffffffffffffffffffff and after starting car you have to reprogram injectors thanks it's easy 100% tested for all delphi dci 1.5

[pittu]

please is possible total immo off in this car? thanks:stoned:

[losing.control]

Hello friends,is there any 100% working solution for this Delphi ecu?i have one clio 1.5 dci from 2002 with delphi ecu and i have immo fault.the ligth on dash is always on and the car not work.if you can help,i appreciate.many thanks in advance.

[auto16]

read your dump files 25080 put first line fffffffffffffffffffff and after starting car you have to reprogram injectors thanks it's easy 100% tested for all delphi dci 1.5

[losing.control]

read your dump files 25080 put first line fffffffffffffffffffff and after starting car you have to reprogram injectors thanks it's easy 100% tested for all delphi dci 1.5

Thank friend now the car runs good,but for sometimes if i let the car stanby(ignition off) and then try to start the car the check engine dont comes on and immo ligth stills on,try second time car works perfect.any clue??big thanks

[bodzio012]

Hi!!!!
I damage 25080 when desolder, can I use other dump from 1.5 dci delphi???
My car is kangoo 2002 year 1.5 dci

HOM8200129109

[miha99]

If you damage 25080 than use new one or from other ecu,put in first line fffffffffffffffffffff after start reprogram injectors with clip.Of course emulator is a must!

[ricampr]

read your dump files 25080 put first line fffffffffffffffffffff and after starting car you have to reprogram injectors thanks it's easy 100% tested for all delphi dci 1.5

hello
I did line 0000 (ffffffffffffffffffffffff) and works in delphi car clio dci. can you help me?
Here is the original file

immo dci 25080 (http://www.mediafire.com/download.php?trkhb1xi71cu7nb)

[gaversa]

I can't go past the key to decompress thanks

[athlonxp]

I have problem with clio 1.5dci 2001 immo. So I need to put ffff in 0000 line in 25080. But how to connect emmulator? There are can line and k-line for diagnostic.

[marouane]

hi use this emlator metode .

[athlonxp]

hi use this emlator metode .
but immo signal comes to ecu by can line not k-line. k-line is for diagnostic, so what is metod to connect emmu? I found metod only with version delphi without can. Mine is with can.

[gadroulll]

As far a i read this post .
you must do first line all ff , and after you program injector and the car starts ?or the car starts and you have not gas pedal and you have to program injector .

you connect emulator to pin 10 of processor ? or you do not need it?

[atenam26]

:barscarf:hi

[damachado]

Hello guys. Mabe some of you can help.

Anyone knows were i can buy this chip in europe fast i tried farnell but no luck.

I will post foto and datasheet.

Any help on this is greatly apriciated.


Regards

[elremont]

If you damage 25080 than use new one or from other ecu,put in first line fffffffffffffffffffff after start reprogram injectors with clip.Of course emulator is a must!

Hi

this work on nissan 1.5 dci delphi ecu? what emulator should I use?

[mrchip]

hello
How can I see difference between K-Line and Can-Bus ECU ( renault 1.5 dci DDCR ecu )?
different eprom ?