View Full Version : Need help with Volvo S60 0 285 001 656
rrador
7th June, 2011, 04:09 AM
Hi guys,
Need some helt with this one, 2007 Volvo S60.
Bosch 0 285 001 656
Does it have CR16 inside?
I have Carprog and UPA, need some help to read this one
Thanks,
morfej
7th June, 2011, 06:40 AM
It is CR16MCT9JE7 to be precise.
For UPA use attached shematic.
br
unu
7th June, 2011, 06:56 AM
Hi guys,
Need some helt with this one, 2007 Volvo S60.
Bosch 0 285 001 656 begin_of_the_skype_highlighting 0 285 001 656 end_of_the_skype_highlighting
Does it have CR16 inside?
I have Carprog and UPA, need some help to read this one
Thanks,
CR16 inside ... very simple to read with UPA_USB
rrador
7th June, 2011, 02:33 PM
Thanks guys. But how do I remove this board from the housing to get to the processor? I tried and it doesnt seem to move at all
giannis4x4
7th June, 2011, 03:26 PM
Read it with carprog, it can do it!good luck
rrador
7th June, 2011, 05:19 PM
Read it with carprog, it can do it!good luck
does anyone know which points i need to bridge to read it through k-line with carprog?
also what pins are +/- and k-line
rrador
8th June, 2011, 02:56 AM
thanks everyone for the help, got it done with carprog.
pinouts were the same as in the carpog manual.
I just wasnt sure at first because it was different module number.
mcm44
8th June, 2011, 07:38 AM
Did you safe original dump maybe? Can you post it?
rrador
8th June, 2011, 02:03 PM
Did you safe original dump maybe? Can you post it?
Yes i will post it later when i get home.
Does anyone know resistance for seatbelt on this car maybe?
mcm44
8th June, 2011, 08:12 PM
Ok, thanks, so I'm waiting... :)
Seat belt's resistance should be like in other cars, between 2 - 3 ohms. But keep in mind, that it has capacitor inside plugs, and SRS unit don't check resistance, but capacity...
rrador
8th June, 2011, 11:17 PM
here is the original dump
credoline
9th June, 2011, 12:21 PM
This sholud be cleared.
rrador
10th June, 2011, 02:02 AM
This sholud be cleared.
I didnt have time to try your file today, will try it tomorrow.
I tried the one carprog cleared automaticaly but i get codes 0259 and 0261 which i think are for passenger ocupant sensor?
I think its a bad clear file as the only thing that was changed on this car is driver airbag.
here is carprog cleared file to compare
credoline
10th June, 2011, 08:38 PM
Not sure, carprog very rare make it wrong. Check what errors are exactly and find in car problem
rrador
11th June, 2011, 04:23 PM
Not sure, carprog very rare make it wrong. Check what errors are exactly and find in car problem
Everything looked good in car so i tried clearing again, and for some reason every time i tried with carprog it gave me different solution?
But your file worked thanks a lot. :beer:
credoline
12th June, 2011, 08:10 PM
Always in the mood for good beer. But you are too far away
wzmak123
10th July, 2012, 10:35 AM
Hi can you send me the pass for file 07_S60_0 285 001 656_CR16_clear.rar ?
Thanks
andrey
18th April, 2015, 05:35 PM
thanks everyone for the help, got it done with carprog.
pinouts were the same as in the carpog manual.
I just wasnt sure at first because it was different module number.
how did you read it bro!!!??? i try with orig carprog no luck !
i think i doing someting wrong . did you solder to back pcb? or kline ? or maybe both kline plus to pcb?
please help!!!
Powered by vBulletin® Version 4.2.5 Copyright © 2024 vBulletin Solutions Inc. All rights reserved.