Porshe Durametric Software needed for China Clone

[blacktoy]

pls delete

[stonedagain]

Download from here: Porsche Diagnostic Tool Manuals and Drivers (http://www.durametric.com/downloadv5.aspx)
This is version 5, works with my china clone. It gives a non-genuine cable warning when you use it but seems to work OK. Instructions & drivers are there also.

[blacktoy]

pls delete

[blacktoy]

pls delete

[stonedagain]

I've tryed now the v5 but the software is stating thath this is an enthusiastic version -> will it fix my interface to only 1 VIN?

br
Not sure with it being a clone, btw the enthusiast version allows 3 vins.

[lulu2003]

I would not try V5 original Software with clone. They brick it.
the china clone comes with a very old and very little working version.

[eastern]

I do have version 5.0.8.0 which works with the clone cable. If anyone needs it I can upload it on web.

[blacktoy]

pls delete

[mmikee]

Hi,
Do anyone have v.5 of Durametric software which works with the clone cable?

[stonedagain]

Hi,
Do anyone have v.5 of Durametric software which works with the clone cable?
Read the 2nd Post!

[LaiWongBao]

It would be greatly appreciated if someone can upload an older version of durametric that works with the clone cable no problem.

[randomlog]

Anyone knows if version 6 can be compatible with china clone ?.


Version 6 requires a 2nd-generation Durametric cable (sold exclusively since March 2008).

[LaiWongBao]

No it will not.

[LaiWongBao]

I would like to ask once again if anyone has the older version of 5.0 available.

[Turbo997]

I do have version 5.0.8.0 which works with the clone cable. If anyone needs it I can upload it on web.

@eastern, do you still have Durametric version 5.0.8.0? If so, can you please send to me or upload on web where I can download? Thank you.

[PhrogPhlyer]

@eastern, do you still have Durametric version 5.0.8.0? If so, can you please send to me or upload on web where I can download? Thank you.
Turbo - Did you get Ver 5 from Eastern? If so can I get a copy?
Thanks

[peterjohn]

Hi Everyone,
does someone have the 5.0.x version? If so may I have a copy?
Thanks in advance!
Peter

[lemm]

Hi Everyone,

I am having the same issue.

Does anyone have the 5.0.x version? And may I have a copy, please?
Thanks in advance!

lemm :friendly_wink:

[bmartin]

Hi Everyone,

I am having the same issue too.

Does anyone have the 5.0.x version? And may I have a copy, please?
Thanks in advance!

bmatin

[dingers]

Hi,

Hopefully this thread is still alive. The present available version following advice in reply 2 gives 5.14. I am tempted to try this but worried about damaging the management unit "Bricking it". However if V. 5.0 is available does anyone have ideas as to where from? Any assistance or advice would be appreciated. Thank you.

[Superblond]

This is the 3.x version of that P_RSCHE PIWIS / DURAMTIC Kabel Software.
https://mega.nz/#!BcpBRYYT!3ePndTV5qI1Uva6jxS55I_XSeaIjQN1e2AI2Pu5 1uBM

That version woked with my chhina cable version....

Also included drivers and NetDot if needed.
To start that tool you need to have the cable pluged into the usb port and the car ODB port.

If you run into any problems, choose WIn7 compatibility mode, or WinXP SP3.

Plz share an spread.

If the link is down, just PM me...

SB

[maxtor911]

hello guys,
still wondering if v5.0 works on the china clone?
can anybody write a reputation if clone and version 5.x.x is tested successfully?

regards