audi a4 2002 abs recoding problem

[markovojvodic]

hello i have audi a4 2002 year with avf engine and i have a problem with abs unit , batery was disconnected
and ecu was decoded , car is audi a4 front drive with manual shift , login is 9555 and xode is 4255 and after i do coding and it was accepted next time i connect to ecu code is again 00000

any idea would be apreciated

[haroutioun]

Hello,
in your rear of trunk it must have Sticker near the Spare Tire,so plz read the engine ecu & transmition 3 digit codes and send it to us .to check whitch corect login & coding you have...
good luck..

[markovojvodic]

im sending you label picture in a minute, i used this sticker to calc the login and code from wiki ross tech .....

login i calculated right or wrong i dont know is 9555 and code is 4255

[haroutioun]

Hi, your photo show me your system is (1LB) SO PLZ TRY
1) LOGIN 09579
2) CODING 04279
3) FOR BASIC SETTING. LOGIN 40168...
let me know if any new....

[markovojvodic]

thank you i will try in the afternoon ....

[markovojvodic]

this is after a aucesfull coding and my restarting xommunication with abs

[markovojvodic]

same thing hapends any other idea

[maucontacto]

Hi!!

I was with the same problem on hands with 2 VW passat... VCDS, Texa, VAS... Nothing!!
After all i use KTS from Bosch and all goes fine!! After coding you have to calibrate G85!!

BR

[haroutioun]

hi dear friend ,tomorow i was at my garage and i well send to you another login and coding .....but plz do autoscan & send to me your autoscan file.
good luck...

[markovojvodic]

autoscan is with no errors ..... anywhere expet dash where is fault : comm with abs controller

[madjohn]

try this

engine running MBV 005 check the steering angle it need to be 0 d ish
try to login in 09555 > code module to 04255 > back to login 40168 > basic setting 001 (save this / or perform basic settings) > turn the steering right hand untill the stop for 3 second then left hand the same then back to the center

then quit the ABS untill your on the main home screen > switch of the car remove the key then a quick drive down the road.. the DTC should be now clear and abs light out.

all after login and coding the G85 must be adapted before the coding is accepted to the module..

[haroutioun]

Dear, you must try many times because some times he cant accept from first time .so wath you need to do you can go to www.ross-tech.com (http://www.ross-tech.com) in this site you get every thing you need to slove about ABS.so in the vcds to have help to how use choose the login number and coding ....
in the end if you dont slove your problam plz send to me autoscan file ,i no you dont have fault in your system but this can help me the found the exectly the numbers of opration.
so i wish to you good luck...

[markovojvodic]

i solved it but onl after i replaced abs control module with another one ...... then it was done immediatly

[diga1]

maybe abs was from automatic gear box,i cant be coded to manual gear box

[markovojvodic]

it was an original abs controller the mechanic just disconnected battery ....and problem appeared after

[sherl645]

I also have had a lot of trouble with these with VCDS. My Bosch KTS codes them fine though.
Ronan

[markovojvodic]

i tried with VAS 5052 , brainbee , vcds and bosch, the new controller i coded from first try with vcds

[Furax]

Ive had this problem in the past but it was due to having the login code wrong. It seemed to work ok but reverted back to 0000's after.

Anybody having this problem in the future I would advise to triple check the codes right!